Philips RFX600099 User manual

Philips RFX600099 Manual

Get Philips RFX600099 PDF manuals and user guides View all Philips RFX600099 manuals
Add to My Manuals
Save this manual to your list of manuals

Philips RFX600099 manual content summary:

  • Philips RFX600099 | User manual - Page 1
    Introduction Introduction Note: In this user guide Pronto is used for both ProntoPro and Pronto remote controls. RFX6000 is compatible with TSU3000 and TSU6000. About the RFX6000 Most remote control systems have to be operated by pointing the remote control directly towards a device. Any obstacle
  • Philips RFX600099 | User manual - Page 2
    RF Extender can be used in several situations: • Your devices can be remotely controlled while the RF Extender is placed in line of sight (situation A). all RF Extenders with the same Pronto Remote Control. See Multiple RF Extenders on p. 6 to apply the necessary settings. Situation B Situation
  • Philips RFX600099 | User manual - Page 3
    apply to your needs. It is recommended to read through the entire User Guide. Working Angle and Range of the IR blaster Warning The IR signals sent 4 inches (10 cm) Maximum distance: Approx. 16 feet (5 m) User Guide Figure 1: IR blaster facing down Figure 2: IR blaster facing up Figure 1
  • Philips RFX600099 | User manual - Page 4
    . Warning It is adviced not to place the RF Extender inside or near a metal closet as RF signals can be disturbed by metal objects. User Guide 1 Remove the mounting plate from the bottom of the RF Extender. 2 Screw the plate to a rack, closet or another piece of furniture. Provide sufficient space
  • Philips RFX600099 | User manual - Page 5
    LED on the RF Extender. Note To avoid interference, the adapter cable should be kept away from the RF Extender as far as possible. User Guide 5
  • Philips RFX600099 | User manual - Page 6
    one RF Extender, you can accept the default setting for the Extender ID (ID=0). Make sure your Pronto Remote Control is set to the same default setting (see the Pronto User Guide for more details). Multiple RF Extenders If you want to operate several of your devices independently, e.g. grouped on
  • Philips RFX600099 | User manual - Page 7
    Troubleshooting Troubleshooting Devices do not respond properly • Check if the power adapter is connected and the red LED is on. • Check if the ID and channel numbers on the RF Extender match with the ID and channel numbers on the Pronto Remote Control (see p. 6). Refer to the Pronto User Guide
  • Philips RFX600099 | User manual - Page 8
    to 50°C) Operating distance: up to 16 feet (5 meters) IR frequency range: DC/flash codes, 36kHz-550kHz Operating distance: up to 100 feet (30 meters) depending on the surrounding conditions Frequency . Philips Consumer Electronics Company, Knoxville, Tennessee 37914 - 1810 U.S.A. User Guide 8
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
User Guide
1
Introduction
Note:
In this user guide Pronto is used for both ProntoPro and Pronto remote controls.
RFX6000 is compatible with TSU3000 and TSU6000.
About the RFX6000
Most remote control systems have to be operated by pointing the remote control
directly towards a device. Any obstacle between the remote control and the device
disturbs the operating signal. But what if you like to place your devices inside a
closed cabinet, a closet or even in another room?
The RFX6000 provides the solution to overcome obstacles like furniture or walls.
Your devices no longer have to be placed in line of sight but can be operated from
virtually any location. The RFX6000 is a RF Extender that is used in combination
with the Pronto Remote Control. The RF Extender receives
radio frequency
(RF)
signals sent out by the Pronto and converts them into
infrared
(IR) signals. These
IR signals are then sent out to your TV, DVD, preamplifier and so on.
Introduction
Pronto
RF Extender
RF signals
IR signals