Pioneer DEH-P4700MP Other Manual

Note:

•

This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

•

To avoid shorts in the electrical system, be sure to

disconnect the

≠

battery cable before beginning

installation.

•

Refer to the owner’s manual for details on con-

necting the power amp and other units, then make

connections correctly.

•

Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

•

Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

•

Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

•

Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

•

Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

•

When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

•

Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right

≠

speaker leads are common.

•

The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the ground

becomes detached, there is a risk of damage to the

products or fire.

•

Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

ance of 4 to 8 ohms. Connecting speakers with out-

put and/or impedance values other than those

noted here may result in the speakers catching fire,

emitting smoke, or becoming damaged.

•

When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.

Connect to an external power amp’s system remote

control or the car’s Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

•

When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do not

connect the blue/white lead to the power terminal

of the auto-antenna. Such connection could cause

excessive current drain and malfunction.

•

To avoid a short-circuit, cover the disconnected

lead with insulating tape. Insulate the unused

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

•

To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connections of the same col-

ors correctly.

•

If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be connected

to a terminal coupled with ignition switch ON/OFF

operations. If this is not done, the vehicle battery

may be drained when you are away from the vehi-

cle for several hours. (Fig. 1)

Fig. 1

•

Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied manuals of

both products and connect cords that have the

same function.

No ACC position

ACC position

O

N

S

T

A

R

T

O

F

F

A

C

C

O

N

S

T

A

R

T

O

F

F

<KNNZX> <04J00000>

Printed in Thailand

Imprimé en Thaïlande

<CRD3948-A/N> UC

+

≠

+

≠

+

≠

+

≠

IP-BUS input (Blue)

This product

Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Connecting cords

with RCA pin plugs

(sold separately)

System remote control

Rear speaker

Rear speaker

Right

Front speaker

Rear speaker

White

Gray

White/black

Green

Green/black

Gray/black

Violet

Violet/black

Front speaker

Rear speaker

Left

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Black (ground)

To vehicle (metal) body.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Antenna jack

Rear output

(REAR OUTPUT)

Perform these connections when using

the optional amplifier.

Front output

(FRONT OUTPUT)

Power amp

(sold separately)

Front speaker

Front speaker

Right

Left

Fuse

+

≠

+

≠

+

≠

+

≠

Power amp

(sold separately)

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

IP-BUS cable

Multi-CD player

(sold separately)

Fig. 2

<ENGLISH>

Connecting the Units

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

INSTALLATION MANUAL

MANUEL D’INSTALLATION

DEH-P4700MP

Pioneer DEH-P4700MP Other Manual

Pioneer DEH-P4700MP Manual

Pioneer DEH-P4700MP manual content summary: