Poulan PLN1514 User Manual

Poulan PLN1514 Manual

Get Poulan PLN1514 PDF manuals and user guides View all Poulan PLN1514 manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan PLN1514 manual content summary:

  • Poulan PLN1514 | User Manual - Page 1
    ne pas retourner I'outil au detaillant, 1-800-554-6723 www.poulan.com Instruction Manual Manual de Instrucciones Manuel d'Instructions PLN1514 ItToI 245157 r- c Us A WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in
  • Poulan PLN1514 | User Manual - Page 2
    is running, 10 ELECTRIC MOTOR is double insulated for added safety. 14 CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails during operation. The catcher is designed to intercept a whipping chain. SPECIFICATION Input Peak Horsepower Bar Length Chain Oil Capacity Net
  • Poulan PLN1514 | User Manual - Page 3
    PRECAUTIONS FOR CHAIN SAW USERS WARNING PINCHING the saw chain along the 2-1. DANGER! BEWARE OF KICKBACK! TOP of the guide bar may PUSH the guide bar rapidly back toward the operator. Kickback can lead to dangerous loss of Any of these reactions may cause you to control of the chain saw and
  • Poulan PLN1514 | User Manual - Page 4
    should be properly repaired or replaced by an authorized service center,unless otherwise indicated in this instruction manual. 18. CARRYING THE SAW: Carry the saw by the front handle with the saw stopped.Keep your finger off the switch, and make sure that the guide bar and saw chain are to the rear
  • Poulan PLN1514 | User Manual - Page 5
    . 38. All chain saw service, other than the items listed in the user manual safety and maintenance instructions, should be performed by competent chain saw personnel. Do not attempt to repair It yourself; there are no user serviceable parts inside. NOTE:Low-kickback saw chain is chain that has met
  • Poulan PLN1514 | User Manual - Page 6
    oil before the unit is ready for operation.Do not start the saw motor until the unit is properly prepared. Read all instructions carefully.Do not install any other size bar and chain than what is recommended by the manufacturer for your model PLN1514. 3-4.GUIDE BAR / SAW CHAIN REPLACEMENT
  • Poulan PLN1514 | User Manual - Page 7
    OILING CHAIN To oil chain, press oil cap.Oil will feed onto guide bar and chain.Press oil cap at least once before each cut.Always check oil level before using pole saw.Do not attempt to operate the oiler while cutting with the pole saw. 3-7.FILLING OIL TANK Using a funnel, fill oil tank with Poulan
  • Poulan PLN1514 | User Manual - Page 8
    the trigger squeezed to restart the motor. 4-3. CHAIN AND BAR LUBRICATION Always check oil level before using saw. To oil chain, press oil cap.Do not attempt to operate the oiler while cutting with the saw. Oil will feed onto guide bar and chain. Press oil cap at least once before each cut. Check
  • Poulan PLN1514 | User Manual - Page 9
    Your double insulated appliance has no serviceable parts inside. Do not attempt to repair it yourself.For service information, contact the Poulan Product Service Department toll-free number listed on the back cover of this manual. 5 - GENERAL CUTTING INSTRUCTIONS 5-7. FELLING Felling is the term
  • Poulan PLN1514 | User Manual - Page 10
    3/4 1/4 c _1_ -F 5-1B Never saw completely through the trunk.Always leave a hinge.The hinge guides the tree.lf the trunk is completely cut supported at both ends and you must cut in the middle, make the undercut. This will prevent the log from pinching the bar and chain. Be careful that the chain
  • Poulan PLN1514 | User Manual - Page 11
    depth gauge settings cause most guide bar problems, primarily resulting in uneven bar wear.As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in making straight cuts. Insufficient guide bar lubrication and operating the saw with a chain that is TOO TIGHT will
  • Poulan PLN1514 | User Manual - Page 12
    professional chain saw operator. WHAT IS A LOW-KICKBACK SAW CHAIN? A low-kickback saw chain is a chain which has met the kick-back performance requirements of ANSI B175.1.Do not use other replacement chain unless it has met these requirements for your specific model. By keeping the saw chain in
  • Poulan PLN1514 | User Manual - Page 13
    not operate, contact the Poulan Product Service Department, through the toll-free number listed on the back cover of this manual, for service information.Do not attempt to repair it yourself. No serviceable parts are inside. 7-2. CHAIN REPLACEMENT INFORMATION Drive Links 49 DL Bar P/N Length
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Poulan®
9
Please
do
not
return
unit
to
retailer,
Por
favor,
no
devuelva
el
aparato
al
lugar
de
compra.
Veuillez
ne
pas
retourner
I'outil
au
detaillant,
•
1-800-554-6723
www.poulan.com
A
Instruction
Manual
Manual
de
Instrucciones
Manuel
d'Instructions
PLN1514
245157
WARNING:
c
Us
Read
and
follow
all
Safety
Rules
and
Operating
Instructions
before
using
this
product.
Failure
to
do
so
can
result
in
serious
injury.
ADVERTENCIA:
Lea
el
manual
de
instrucciones
y
siga
todas
las
advertencias
e
instrucciones
de
seguridad.
El
no
hacerlo
puede
resultar
en
lesiones
graves.
AVERTISSEMENT:
Lire
le
manuel
d'instructions
et
bien
respecter
tous
les
avertisse-
ments
et
toutes
les
instructions
de
securite.
Tout
defaut
de
le
faire
pourrait
entrainer
des
blessures
graves.
Poulan
1030
Stevens
Creek
Road
Augusta,
GA
30907
Poulan
850
Matheson
Blvd,
West
Mississauga,
Ontario
L5V
0B4
9096-210916(2)
ITI
to
r-