Home » Poulan Manuals » Lawn & Garden » Poulan PPB1634 » Manual Viewer

Poulan PPB1634 User Manual

Poulan PPB1634 Manual

Get Poulan PPB1634 PDF manuals and user guides

View all Poulan PPB1634 manuals

Add to My Manuals
Save this manual to your list of manuals

Poulan PPB1634 manual content summary:

Poulan PPB1634 | User Manual - Page 1
ENGLISH R Instruction Manual Manual de Instrucciones Manuel d'Instructions PPB1634 PPB1838 ESPAÑOL For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea el manual de
Poulan PPB1634 | User Manual - Page 2
understand and can follow safety rules, precautions, and operating instructions found in this manual. S Wear protective gear. Always use steeltoed safety footwear Safety Hat Eye Protection Heavy Duty Gloves Safety Chaps S Keep all parts of your body away from the chain when the engine is running
Poulan PPB1634 | User Manual - Page 3
service performed by a qualified service dealer with the exception of the items listed in the maintenance section of this manual tightened. S Use only Poulan PROR accessories and replacement parts as recommended. HANDLE FUEL object at the upper tip of the guide bar. This contact can cause the chain
Poulan PPB1634 | User Manual - Page 4
do not rely only on safety devices. You must follow all safety precautions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury. S Reduced--Kickback Guide Bar, designed with a small radius tip which reduces the size of the kickback
Poulan PPB1634 | User Manual - Page 5
allows wood to gradually ride into cutter Can Obstruct servicing dealer, or to the nearest authorized master service dealer. S Tip contact in some cases may cause a lightning fast reverse REACTION, kicking guide on saws listed in this manual. Use of bar and SERIES MODEL PPB1634 PPB1838 BAR P/N
Poulan PPB1634 | User Manual - Page 6
guarantee the avoidance of these problems. Users who operate power parts. Failure to do so is a violation of the law. Refer to the SERVICE manual, use care and good judgement. If you need assistance, contact your authorized service . 5. Slide guide bar behind clutch drum until guide bar stops against
Poulan PPB1634 | User Manual - Page 7
Bar Adjusting Screw -- 1/4 Turn ENGAGED Chain Brake 11. Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned. 12. Install chain brake nuts and finger tighten only. Once
Poulan PPB1634 | User Manual - Page 8
INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual / Trigger Fast Idle Lever Chain Brake Guide Bar Chain Brake Chain Nuts Catcher Bar
Poulan PPB1634 | User Manual - Page 9
When mixing fuel follow the instructions printed on the container. refer to CARBURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. . Poulan or Poulan PROR oil resists high temperature thinning. If Poulan or Poulan PROR in storage. To avoid engine problems, the fuel system should be
Poulan PPB1634 | User Manual - Page 10
TROUBLESHOOTING service dealer if any part is worn to less service dealer. S This saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs. S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually the guide
Poulan PPB1634 | User Manual - Page 11
S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, unnecessary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for longer than 30 seconds at full
Poulan PPB1634 | User Manual - Page 12
your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn't fall completely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor. CUTTING A FALLEN TREE (BUCKING) Bucking is the term used for cutting a fallen tree
Poulan PPB1634 | User Manual - Page 13
not listed in this manual be performed by an authorized or Master Service Dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level . . . . Before each use Bar lubrication Before each use Chain tension Before each use Chain sharpness . . . . Before each use For damaged parts . . Before each use For
Poulan PPB1634 | User Manual - Page 14
Cover 2. Remove the bolt cover. 3. Loosen and remove the 2 muffler bolts. Remove the muffler, muffler gasket, outlet guide and backplate. Notice the orientation of these parts for reassembling. 4. Locate the 2 outlet cover screws on the muffler. Loosen and remove both screws. 5. Remove the outlet
Poulan PPB1634 | User Manual - Page 15
been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain
Poulan PPB1634 | User Manual - Page 16
, bars, chains, and other parts which wear and require replacement with reasonable use during the warranty period. This warran- ty does not cover predelivery set--up, installation of guide bar and chain, and normal adjustments explained in the instruction manual such as carburetor adjustments and
Poulan PPB1634 | User Manual - Page 17
such an emission related part, the part will be repaired or replaced by ELECTROLUX HOME PRODUCTS, INC. OWNER'S WARRANTY RESPONSIBILITIES: As the small off--road engine engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. ELECTROLUX HOME
Poulan PPB1634 | User Manual - Page 18
The information on the product label indicates which standard your engine is certified. Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA. This engine is certified to be emissions compliant for the following use: Moderate (50 hours) Intermediate (125 hours) Extended (300 hours) 18