Pyle PHMD55 Instruction Manual
Pyle PHMD55 Manual
 |
View all Pyle PHMD55 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PHMD55 manual content summary:
- Pyle PHMD55 | Instruction Manual - Page 1
- Pyle PHMD55 | Instruction Manual - Page 2
TERMINOLOGY The following terms are the common terminologies among the metal detector. Motion Mode Continuously moving the search coil is one of the circuit operation modes within the metal detector's built-in detection technologies. You have to move the search coil during detecting -- preferably in - Pyle PHMD55 | Instruction Manual - Page 3
Iron Iron is a common metal, it's usually not the dedicated detection target. Undesirable iron objects include iron nails, bolts, old cans, caps, etc. Valuable relics and sought after materials can also be composed of iron, such as old armaments, old armature, etc . So, it may be best to pay - Pyle PHMD55 | Instruction Manual - Page 4
Assembly Wind the cable around the aluminum tube arm, keep the elastic moderately tight/loose, so that the cable won't sway or interfere with operation and clothing. Tighten appropriately the two ends nuts, and adjust the search coil location to let the search coil be parallel with the ground. Be - Pyle PHMD55 | Instruction Manual - Page 5
LCD Digital Display Screen During detecting, the metal targets are divided into three categories by the target identification cursor. SILVER - Higher conductivity metals, such as silver, aluminum and copper (Such as coins: .25cents, 50cents and 1 U.S. dollar coin can be illumined at this point) MID - Pyle PHMD55 | Instruction Manual - Page 6
(4) Level Discrimination Modes (4) Modes Initial state Press "MODE" Until Set Press "MODE" Until Set Press "MODE" Until Set Press "MODE" Until Set Indication Sound TARGET ID Indication The Eliminated Metals High tone Not illumined Can't eliminate any metals Low tone Iron is illumined NOTCH - Pyle PHMD55 | Instruction Manual - Page 7
Powering On Press the POWER ON button, the detector will sound three frequencies of low, medium and high tones, the liquid crystal dsplay shows the discrimination mode and the sensitivity. *When the TARGET ID is not illuminated, that indicates the metal detector is in the 'ALL METAL' mode. * - Pyle PHMD55 | Instruction Manual - Page 8
Eliminate Iron - Elimination: Operation Indication LCD TARGET ID LCD DEPTH-SENS LCD Chart Note Press MODE button Three low tones IRON is lighted SENS-3 is illuminated Sweep iron nail No tone IRON flickers once SENS-3 flicker once Sweep 5¢ or pull-tabsmtonedeium MID RANGE DEPTH-2 is - Pyle PHMD55 | Instruction Manual - Page 9
the oxidation degree of the underground metals, and soil, will all affect the detection, discrimination and pinpoint targeting results. This manual and user instruction only describe the general and typical steps / practices of the field detection. The operator should familiarize himself with tested - Pyle PHMD55 | Instruction Manual - Page 10
Motion detection When detecting using the moving 'Motion Mode', you should sweep the search coil at a constant (fairly slow and steady) speed, and let the search coil remain parallel with the ground floor surface. Preferred height distance of the coil from the ground floor surface is about 1/2 - Pyle PHMD55 | Instruction Manual - Page 11
continue moving forward. Take the time to practice and experiment the ideal sweeping speed and style. Learning, experimenting and discovering is all a part of the experience and you will gradually develop metal detecting skills and sought-after habits over time. Pinpoint your finding When there is a - Pyle PHMD55 | Instruction Manual - Page 12
Troubleshooting SYMPTOM No power, there is no indication on the LCD display, there is no sound when powering on Sound heard is an irregular tone, or - Pyle PHMD55 | Instruction Manual - Page 13
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
