Pyle PIRT30 PIRT30 Manual 1

Pyle PIRT30 Manual

Get Pyle PIRT30 PDF manuals and user guides View all Pyle PIRT30 manuals
Add to My Manuals
Save this manual to your list of manuals

Pyle PIRT30 manual content summary:

  • Pyle PIRT30 | PIRT30 Manual 1 - Page 1
    pyleaudio.com User Manual Wide Range InfraRed (IR) Thermometer with Type K input and Laser Pointer PIRT30
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 2
    feature allows the IR thermometer to measure the temperature of virtually any surface. This meter is shipped fully tested and calibrated and, with proper use, will provide years of reliable service. * The supplied thermocouple is rated for 482oF (250oC). Safety • Use extreme caution when the
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 3
    Meter Description 1. Laser pointer 2. IR Sensor 3. Measurement Trigger 4. Battery and Switch compartment 5. LCD Display 6. Function Buttons 7. Type-K thermocouple 8. Temperature units (oC or oF) switch Note that switches are located in the battery compartment behind the battery. 1 2 5 6 3 4 7 3 8
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 4
    Operating Instructions IR (non-contact) Measurements 1. Hold the meter by its handle and point it toward the surface to be measured. 2. Pull and hold the trigger to turn the meter on and begin testing. The temperature reading, the flashing 'SCAN' icon, the emissivity, and the unit of measure will
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 5
    % of all applications. Emissivity is discussed in a dedicated section of this manual. MAX (Maximum function) In the MAX mode, only the highest reading k' icon display. If the sensor is not correctly inserted to the meter the display will show all dashes '-----'. The supplied thermocouple is rated
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 6
    has an alarm feature whereas a High Alarm setting and a Low Alarm setting can be programmed by the user. When either Alarm point is reached the meter will alert the user via an audible beep and LCD display icon. Follow the steps below: 1. Press the MODE button until the HAL (High Alarm
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 7
    under test should be larger than the spot (target) size calculated by the field of view diagram (printed on the side of the meter and in this guide). 2. Before measuring, be sure to clean surfaces that are covered with frost, oil, grime, etc. 3. If an object's surface is highly reflective, apply
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 8
    Theory IR Thermometers measure the surface temperature of an object. The thermometer's optics sense emitted, reflected, and transmitted energy. The thermometer's electronics translate the information into a temperature reading which is then displayed on the LCD. The amount of IR energy emitted by an
  • Pyle PIRT30 | PIRT30 Manual 1 - Page 9
    Automatic Power Off Weight Dimensions Backlit LCD display with function indicators 1 second approx. 32oF to 122oF (0oC to 50oC) 80% Relative Humidity max. 9V battery Meter shuts off automatically after 7 seconds 165g 178.5X42X90.5 9
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
User Manual
Wide Range InfraRed (IR) Thermometer
with Type K input and Laser Pointer