Pyle PLTA580 PLTA580 Manual 1
Pyle PLTA580 Manual
 |
View all Pyle PLTA580 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PLTA580 manual content summary:
- Pyle PLTA580 | PLTA580 Manual 1 - Page 1
- Pyle PLTA580 | PLTA580 Manual 1 - Page 2
TRBL.E OF C:ONTENTS TRBL.E OF C:ONTENTS INTRODUCTION & FEATURES 1 FEATU RES & CONTROLS 3 SPECIFICATION 4 CONTROLS & FUNCTIONS 5 SYSTEM WIRING 6-8 TROUBLESHOOTING 9 WI RI NG...10 -1- - Pyle PLTA580 | PLTA580 Manual 1 - Page 3
engineered to give you many years of un compromised musical service. PYLE amplifiers are designed with the latest technology available, incorporating a • Variable high and low pass crossover controls • Thermal and speaker short protection circuitry • Power and Protection LED indicators • Bass - Pyle PLTA580 | PLTA580 Manual 1 - Page 4
Mode, this control limits the frequencies which will be distributed to the speakers to those above the value to which this is set within the range 20 Hz fIXed Provide instant information on status of amplifier, including short-circuit and thermal overload alerts. INPUT LEVEL CONTROL Enables the - Pyle PLTA580 | PLTA580 Manual 1 - Page 5
Ohms MAXat4 Ohms At 4 Ohms Bridged RMSat2 Ohms Min. Speaker Impedance T.H.D Frequency Response Input Sensitivity SIN Ratio Channel Separation Low Pass Filter High Pass Filter Sub Sonic Filter Bass Boost Control Dimensions(inches} Fuse(s) PLTA180 200Wx2 400Wx2 800Wx I 350Wx2 20hm 0.04% 10Hz -35kHz - Pyle PLTA580 | PLTA580 Manual 1 - Page 6
electrical wiring .. 2. Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent unit or other equipment is turned off while connecting the input jacks and speaker terminals. 5. If you need to replace the power fuse, only replace - Pyle PLTA580 | PLTA580 Manual 1 - Page 7
STEM WIRING PLTA180/580 2 channel stereo configuration FRONT REAR .1lI g SubSonic C ~~- r_~.~ I>: • • • @-!;~"l. LWIII I......t U.. aut = = = = = = TO OUTPUT FROM HEAT UNIT = = = = = = TO BATTER~+}--------~ SELECT REMOTE SWITCH LEFT SPEAKER SPEAKER IMPEDANCE 2-40HM RIGHT SPEAKER Fuse - Pyle PLTA580 | PLTA580 Manual 1 - Page 8
PLTA180/580 2 channel bridged mode configuration FRONT =- I>: SubSonic C-r ~~ g 011 011 • • • L ...-' I Lc- • @-!;~"l. LWIII I......t U.. aut = = = = = = REAR TO OUTPUT FROM HEAT UNIT Ii+ REM GND o = = = = = = = = = TO BATTER~+}--------~ SELECT REMOTE SWITCH SPEAKER IMPEDANCE - Pyle PLTA580 | PLTA580 Manual 1 - Page 9
STEM WIRING PLTA180/580 2 channel tri-mode configuration FRONT REAR =- I>: SubSonic C-r ~~ g 011 011 • • • L ...-' I Lc- • @-!;~"l. LWIII I......t U.. aut = = = = = = TO OUTPUT FROM HEAT UNIT = = = = = = TO BATTER~+}--------~ SELECT REMOTE SWITCH LEFT SPEAKER RIGHT SPEAKER Fuse - Pyle PLTA580 | PLTA580 Manual 1 - Page 10
briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. • Disconnect all RCA inputs to the amplifier(s)-if hiss/noise disappears, then plug in the component driving the amplifier and unplug it's inputs. If hissl noisedisappears, go on until the faulty/noisy component - Pyle PLTA580 | PLTA580 Manual 1 - Page 11
configuration. r 2-chennel Amplifier (Operetlng In Bridged Mono) NO! L@J Two 4-ohm speakers, wired in parallel to a bridged two-channel amplifier, will present a 2-ohm mono load to the amplifier. MOST TWO-CHANNEL AMPLIFIERS DO NOT SUPPORT 2·0HM MONO OPERATION I AMPLIFIER DAMAGE COULD RESULTI - Pyle PLTA580 | PLTA580 Manual 1 - Page 12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
