Pyle PPDM1 PPDM1 Manual 1

Pyle PPDM1 Manual

Get Pyle PPDM1 PDF manuals and user guides View all Pyle PPDM1 manuals
Add to My Manuals
Save this manual to your list of manuals

Pyle PPDM1 manual content summary:

  • Pyle PPDM1 | PPDM1 Manual 1 - Page 1
    remove the protective foil from the display when you use the speed master watch for the first time and press the A , C or 0 button D button, all settings are saved. The heart rate monitor watch can be wom like a wristwatCh. Note: By pressing and hOlding the A and C buttons in any time wililum
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 2
    INTRODUCTION WARNING: Always consult your physician before starting a fitness programme. A pulse computer is not a medical device. It is a training tool designed to measure and display your heart rate. USE A PRECISE TRAINING METHOD All the experts agree: the heart is the most important muSCle in
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 3
    alarm • Hour1y chime signal OTHER SPECIFICATIONS • El baCklight • Water resislanl housing BATTERY INSTALLATION ComputorWatch Remove the baCk cover of the watch with a screwdriver, install the 3.0V.battery with the positive(+) pole facing up and replace the cover. Remove the battery and reinsert
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 4
    WEARING THE TRANSMITIER BELT Adjust the elastic belt so that it fits tightly around your chest just below the pectoral muscles. Moisten the transmitter's conductive pads with saliva or ECG-gel (available at your local chemist's) in order to ensure a good contact wi th the skin at all times.
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 5
    year is displayed in the upper segment of the display and the weekday and date in the lOwer segment. Main Function Mode The Speed Master watch has four main function modes, which are described further in the next chapters: • Time Mode - Stopwatch Mode - Heart Rate Mode - Pedometer Mode The first
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 6
    , all settings are saved. .-... 2DDB .-.. TH 508" ~'---_/~ ...-HEIGHT 118C~1 Second Time Keep the C button pressed for about 3 seconds, the heart rate monitor watch changes to the second time (T2 appears on the bottom right of the display). The setting of the second time works as described
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 7
    it off by pressing the A, C or D button. Countdown Timer Press the C button in lime mode until T IMER is d isplayed. The heart rale monitor watch possesses a countdown timer a nd a count up timer. ... T"""IMER Basic setting 00:01 :00 (1 minute) Keep the A button pressed to set the countdown timer
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 8
    STOPWATCH MODE Press the 0 bullon until you reach the stopwatch mode, shown by "C HRONO". In stopwatch mode you can choose between the sub functions • CHRONO (stopwatch) and • DATA RECALL (view data) CHROHO • Press A button to stan J stop the stopwatCh. • Press C button to record the lap memory
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 9
    For your reference. you can following methods to take different measurement STANDARD MEASUREMENT : A-A-A '5 lP 00\ !'5 lP 01\ • DD'DDoo • D1'3568,_ START Press A STOP ~ CODCDC / Press A ~CI3S68 / RECALL LAP MEMORY : C-A-A-......A-C-A STOPWATCH MODE RECALL BEST LAP RECALL FIRST LAP / '5 lP
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 10
    received. The training time shows Ihe lotal time you have wom the chest bell and the heart rate was received by the heart rate monitor watch, even if you switch to another mode from the heart rate mode. If you press the A button shortly, you can choose between the fOllowing displays
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 11
    Memory Press the C button in the heart rate mode until MEMORY is displayed. The saved heart rate data is shown in the lower segment of the display, the current heart rate in the middle, as long as the chest belt is worn. You can look at the following dala by pressing the A button: HI = highest heart
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 12
    Training Zono Alarm Keep the C button pressed with the display of the upper and lower limits. Alarm symbol -I} appears = Training zone alarm activated Alarm symbol disappears = Training zone alarm deactivated If the heart rate drops below the lower limit or it rises above the upper limit, the alarm
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 13
    rough guidance level. The BMI is calculated by dividing the body weight in kg by the body size in metres squared. The heart rate monitor watch automatically calculates the 8MI from the entered data. Speed Atl ention: You first have to calibrate in the pedometer mode, see section speed calibt"ation
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 14
    same speed and rhythm as during calib(ation when you are running and walking, to get a meaningful result. If you wore the heart rate monitor watch on the left (right) hand during calibration, wear it also on your left (right) hand during training. • Keep the A pressed· the display SETIING appears
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 15
    press the A button afterwards. • Display CAli. OK! and SAVE appears The calibration was correct and was saved. • Finally press the 0 button, the watch changes to the initial position (display of current speed and lower and upper limits for the speed). 1: PRESS ST:O ECND Calibration not Successful
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 16
    Stop Calibration Press the 0 button during calibration in case you want to stop the calibration. The display CALI CANCEL appears. The watch automatically changes to the initial position (display of OJrrent speed and lower and upper limits for the speed). You can now start a new calibration. Speed
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 17
    BMI (Body Mass Index) T-"I"2D&:;{ 8: 2001 • 8M I Age (years) 8MI normal value (kglm2 ) 19-24 25-34 35-44 45-54 55-64 >64 19 - 24 20 - 25 21 - 26 22- 27 23- 28 24 - 29 approximate values of the 8 MI The BM I (Body Mass Index) is a measured value for the evaluation of the body weight of humans.
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 18
    can read the display of the heart ra te monitor watch in darkness. A permanent illumination of the display is not possible. Please note that the illum ination consumes more power, which reduces the lifespan of the battery, TROUBLESHOOTING Why is the displayed covered distance incorrect? Have you
  • Pyle PPDM1 | PPDM1 Manual 1 - Page 19
    ot'Iq _ . :u>d IN"'...,..... "".m... ,.,.. NO"'P"kw> SI'." l.my'....", 10 1rl>l wtor. ~;.f' ~,i'
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
.----------------'
I
Activation·
Before starting
Spe
ed
Master
Wat
ch
Please remove the protecti
ve
foil from the display when you use
the speed
master
watch
for the first time and press the A, C
or
0
button (
sound
signat),
unti
l
all
di
splay
segments
appear
for
a
short
li
me
.
You
automatically
reach
setting
the
lfl~S
of
measurement.
• Choose
between
the
metric
and
imperia
l
with
lhe C button.
Confirm y
our
selection wi
th
the A button, the
24h
blink.
Setting the lime in the time
mode
(also see TIME
MO
DE)
•
Choose
between the
12h
and 24h display w
ith
the C button.
Confirm your selection wi
th
the A button, the seconds blink.
Note
:
By
pressing
and
hOlding the C button
you
can
use
the
fast
forward
function
in
the settings.
•
Press
the
C
button
to
reset
the
seconds
to
zero
.
Confirm with the A button, the
minutes
blink.
• Set the minutes with the C button.
Confirm with the A button, the
minutes
blink.
• Set the hours, year,
month
, day,
year
, month
and
day
of
birth. weight and size as
des
cribed above. Now press the D
button, all settings
are
saved.
The
heart
rate
monitor
watch can
be
wom
like a wristwatCh.
Note
: By pressing
and
hOlding the A
and
C buttons in any time
wililum
the watCh
back
to setting
mode
Accessories
o
Transminer
BanelY
(3V
I
CR2032)
T
ra
nsmi
ner Belt
o
Computer
SanelY
(3V
I
CR2032
)
Elastic
Be
lt