Pyle PPDM3 PPDM3 Manual 1
Pyle PPDM3 Manual
 |
View all Pyle PPDM3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PPDM3 manual content summary:
- Pyle PPDM3 | PPDM3 Manual 1 - Page 1
Ihe display when you use the speed master watch for the first time and press Ihe A, C or o button (scund signal), until all display segments appear for a short time. You automatically reach setting Ihe units of measurement (metric or imperial). ALTIMETER WITH Me-me • Choose between Ihe METRIC and - Pyle PPDM3 | PPDM3 Manual 1 - Page 2
FEATURES SPEED MASTER • Digital motion sensor for speed detection • Current speed • Target speed zone • mbar or inHg un~ selectable CHRONOGRAPH • Count-down timer • 11100 second 99 laps multi-split stopwatch WATCH • Dual time clock • Aulo Calendar • CIocl< alarm • HOIJ'Iy chime Signal • Dig~1 clock - Pyle PPDM3 | PPDM3 Manual 1 - Page 3
and date in the lower segment. Main Function Mode The Speed Master watch has five main funcUon modes, which are described further in the next chapters: - Time Mode - Stopwatch Mode - Altimeter Mode - Barometer Mode - Pedometer Mode The first mode displayed is the time mode. Press the D button - Pyle PPDM3 | PPDM3 Manual 1 - Page 4
, all settings is saved. """-~ 2DDB ( TU 912" ~-~ WEIGHT 13KG ( GiJ-~ HEIGHT ISDCM Second Time Keep the C button pressed for about 3 seconds, the Speed Master Watch changes to the second time (T2 appears on the bottom right of the display). The setting of the second time works as described in - Pyle PPDM3 | PPDM3 Manual 1 - Page 5
alarm on Alarm symbol not displayed = alarm off Countdown Timer Press the C button in time mode until TIMER is displayed. The Speed Master Watch possesses a countdown timer and a count up timer. Basic setting 00:01 :00 (1 minute) t!!!!)-~ TInER Keep the A button pressed to set the countdown timer - Pyle PPDM3 | PPDM3 Manual 1 - Page 6
STOPWATCH MODE Press the 0 button until you reach the stopwatch mode, shown by "CHRONO". In stopwatch mode you can choose between the sub functions • CHRONO (stopwatch) and • DATA RECALL (view data) - Pyle PPDM3 | PPDM3 Manual 1 - Page 7
For your reference. you can following methods to take different measurement: STANDARD MEASUREMENT: A-A-A START Press A .. STOP Press A RESET HoldA LAP TIME MEASUREMENT: A-C-C-A-A Lap 2 .. START Press A Press C ~ Press C ..RESET I Hold A - 12- Lap3 lP D) " STOP ""'-~ D11l31Jl Press A , ~ - Pyle PPDM3 | PPDM3 Manual 1 - Page 8
ls (HILL) • Record --~ RLTI Setting the Altitude Press the C button in the altimeter mode until CLOCK or ALTI Is dlspalyed. Keep the A button pressed for about 3 seconds, "SETTING" appears on the display, the altimeter digits will start to flicker. Press the C button to select and then press the - Pyle PPDM3 | PPDM3 Manual 1 - Page 9
of the display. Press A Keep the A button pressed - the display RESET appears reset the total altitude loss. Total Altitude Gain Press the C button In the altimeter mode until UP Is displayed . The total altitude gain is shown in the lower segment of the display, in the midd le the current altitude - Pyle PPDM3 | PPDM3 Manual 1 - Page 10
Memory of Minimum Barometer (LOW) Record Press the C button in the altimeter mode until RECORD Is disp layed . The record is shown in the lower the A button to confirm. Right after the weather state settlng, the barometer digits will start to flicker. Press the C button to select and then press the - Pyle PPDM3 | PPDM3 Manual 1 - Page 11
There are four different states: Sunny, Sunny-doudy, Cloudy and Rainy I I,',._.,'" ,',,---,,', Sunny - - t....-:-~I Sunny-cloudy Time Press the C button in the barometer mode until BARO is d isplayed . The dock is shown in the lower segment of the display, in the middle the current - Pyle PPDM3 | PPDM3 Manual 1 - Page 12
Memory of Maximum Barometer Press the C button in the barometer mode until HIGH is d isp layed . The memory of maximum barometer is shown in the lower segment of the display, in the middle the current pressure. Press the A button, the weather forcast, temperature and time is shown in the middle - Pyle PPDM3 | PPDM3 Manual 1 - Page 13
body icon (~) will animate. Press the A button again to stop the pedometer. The current speed is shown in the middle segment of the display. Note: If in the pedometer mode the watch is keep idle for about 5 minutes, the watch automatically changes Into the time mode. Speed Cal/bratlon and Speed - Pyle PPDM3 | PPDM3 Manual 1 - Page 14
the A button when finished walking. • Display CALI. OKI and SAVE appears The calibration was correct and was saved. • Finally press the 0 button, the watch changes to the Initial position (display of current speed and lower and upper limits for the speed). Callbratlon not Successful. In case the - Pyle PPDM3 | PPDM3 Manual 1 - Page 15
want to stop the calibration. The display CALI CANCEL appears. The watch automatically changes to the initial position (display of current speed and alarm sounds (if activated!). Number of Steps Press the C button In the pedometer mode until STEP Is displayed . The number of steps is shown in the - Pyle PPDM3 | PPDM3 Manual 1 - Page 16
by dividing the body weight In kg by the body size in metres squared. The heart rate monitor watch automatically calculates the BMI from the entered data. Timer Press the C button in the pedometer mode until TIMER Is displayed. The timer is shown in the lower segment of the display, in the - Pyle PPDM3 | PPDM3 Manual 1 - Page 17
average speed are reset to zero. Maximum Speed Press the C button In the pedometer mode until MAX SPEED is displayed. The maximum speed is shown in the lower button, so you cen read the display of Ihe speed master . watch in darkness. A permanent illumination of the display IS not possible. Please - Pyle PPDM3 | PPDM3 Manual 1 - Page 18
TROUBLESHOOTING " not oounted • Have all settings been made? • Have the pedometer turned on? Malfunctions occur The display backlight not work • Are the :",1 r~Pl4IP'ooldwk'cI~)C' (E! Art No :PYLE_SPORTS -PPDM3 - 34- Iholtt'" NY 1110t 1 800-4«
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
SPEED
MASJE7i
ALTIMETER
WITH
Me-me
o
1
Activation·
Before starting
Speed Master Watch
Please remove Ihe protective foil from Ihe display when you use
the speed master watch for the first time and press Ihe
A,
C or
o
button (scund signal), unt
il
all displ
ay
segments appear for a
short time.
You
automatically reach setting Ihe units
of
measurement (metric
or
imperial).
• Choose between Ihe METRIC and IMPERIAL
wilh
the C button.
Confirm your selection
wiIh
the A button, Ihe
24H
blink.
• Choose between Ihe
12H
and
24H
display
wilh
the C button.
Con
fi
rm
your selection
wtlh
the A button, Ihe seconds blink.
Note:
By
preasing and holding tho C
button
you can usa
tho fast forward function In tho settings.
• Press Ihe C button to reset Ihe seconds to zero. Confirm
wilh
Ihe A button, the minutes blink.
• Set the minutes with Ihe C button. Confirm with Ihe A button,
Ihe hour blink.
• Set the hours, year, month, day, weight and height as
described above.
Now
press Ihe
0
button, all settings is
saved.
The speed master watch can be worn like a wristwatch.
-
1 -