Pyle UPLMRA410BT Instruction Manual

Pyle UPLMRA410BT Manual

Get Pyle UPLMRA410BT PDF manuals and user guides View all Pyle UPLMRA410BT manuals
Add to My Manuals
Save this manual to your list of manuals

Pyle UPLMRA410BT manual content summary:

  • Pyle UPLMRA410BT | Instruction Manual - Page 1
  • Pyle UPLMRA410BT | Instruction Manual - Page 2
    cups or washers before tightening mounting bolts. Service may be obtained from an authorized Pyle Audio service center. Contact Pyle Audio and make sure you have a receipt as proof of purchase along with the defective unit. You will be then instructed to send or deliver the malfunctioning unit to
  • Pyle UPLMRA410BT | Instruction Manual - Page 3
    Testing & Connections After all the connections have been made. turn on your stereo and listen for the amplifier to turn on. If there are any unusual noises from the speakers then turn the system off and recheck all the wiring. After you have connected your radio or equalizer to the amplifier, you
  • Pyle UPLMRA410BT | Instruction Manual - Page 4
    PLMRA210BT - System Layout PLMRA210BT 1 RCA (Low Level Input) This unit Is provided with RCA Input jacks. Couple the RCA Input with the car stereo or equalizer outputs using RCA type connector cables. 2 Input Gain Control These are NOT Your amplifiers volume controls. They are a sophisticated
  • Pyle UPLMRA410BT | Instruction Manual - Page 5
    Insulation off your speaker wires that will fit under the screw 9 Speaker Terminals plate to help ensure against speaker wire short circuits. The amp can support an impedance load as low as 2 ohms per channel or 4 ohms in the bridged mode, though a 4 ohm stereo load and 8 ohms bridge load will
  • Pyle UPLMRA410BT | Instruction Manual - Page 6
    Stereo Input Connection RCA Type Terminals High Impedance Low Level Inputs Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability. Stereo Input Connection - RCA Type The Elite Series Amps feature plated RCA terminals for low level input connections to
  • Pyle UPLMRA410BT | Instruction Manual - Page 7
    Mono Input Connection - RCA Type Select Elite Series Amps may easily be bridged for mono operation by feeding the same signal to both LEF T and RIGHT Input terminals. The simplest way to achieve this is by using a Y-adaptor to connecting your car stereo output. Speaker Connection - Stereo Amp System
  • Pyle UPLMRA410BT | Instruction Manual - Page 8
    the instructions found in this manual to help match the signals correctly. Your system can also become extremely sensitive to noise conditions when you have a high signal level coming Into the amplifier, from your connected source, which should be adjusted accordingly. Avoid problems
  • Pyle UPLMRA410BT | Instruction Manual - Page 9
    PLMRA210BT - Wiring Stereo Amp Connection Mono Amp Connection Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 10
    PLMRA410BT - Wiring Stereo Input Connection RCA Input High Level - Speaker Level (BTL or Common Ground) Four Speaker Output Mode Floating Ground Type Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 11
    PLMRA410BT - Wiring Common Ground Type Two Speaker Output Mode Floating Ground Type *High and Low impedance inputs cannot be used at the same time. Note: Elite Series Ampshave built-in short circuit protection. If you mistakingly connect any speaker wires to ground, or positive power ( +) and (-)
  • Pyle UPLMRA410BT | Instruction Manual - Page 12
    power supply directly to the (-) negative ground battery terminal or vehicle chassis. 3. To make a good grounding and prevent motor boating noise problem connect another 12 gauge minimum wire from the (-) negative battery terminal to chassis of stereo unit. 4. Connect the 'Remote' pole to external
  • Pyle UPLMRA410BT | Instruction Manual - Page 13
    PLMRA430BT - Wiring Power Connection Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 14
    PLMRA430BT - Wiring 4 Channel Input Connection Low Level Inputs 2 Channel Input Connection Low Level Inputs High Level Wiring 4 Channel Connection Floating Ground Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability. Elite Series Waterproof
  • Pyle UPLMRA410BT | Instruction Manual - Page 15
    PLMRA430BT - Wiring 4 Channel Mono Connection Low Level Inputs 2 Channel Connection Low Level Inputs 4 Channel Mono Connection Floating Ground Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 16
    PLMRA430BT - Wiring 4 Channel Output Mode Bridged Dual Mono Output 2-8 Ohm 4 Channel Stereo Output Mode with Mono Bridged Subwoofer Output Elite Series Waterproof Amplifiers 4-8 Ohm
  • Pyle UPLMRA410BT | Instruction Manual - Page 17
    PLMRA630BT - Wiring Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 18
    PLMRA630BT - Wiring Electrical Connection 4 Channel Inputs RCA Low Level Mono Input Connection 6 Channels Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 19
    PLMRA630BT - Wiring Speaker Connection 6 Channel Output Mode 2-8 Ohm Speaker Connection Mono Bridged Subwoofer Output Elite Series Waterproof Amplifiers 2-8 Ohm
  • Pyle UPLMRA410BT | Instruction Manual - Page 20
    PLMRA830BT - Wiring Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 21
    PLMRA830BT - Wiring Electrical Connection Multi Channel Input Connection Visit www.PyleAudio.com for detailed model information, specific model wiring and connection ability. Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 22
    PLMRA830BT - Wiring 8 Channel Output Mode 2-8 Ohm Mono Bridged Subwoofer Output 2-8 Ohm Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 23
    Elite Series Bluetooth Connection When searching for the amp via your smartphone or other Bluetooth-enabled device, the Bluetooth amp network name will appear as 'Pyle Amp' in your device list. The amp will not require a password to connect. Once successfully paired with your compatible Bluetooth-
  • Pyle UPLMRA410BT | Instruction Manual - Page 24
    , or feel your system has become faulty, please contact Pyle technical support, or consult the assistance of a trained professional. When replacing fuses, this occurs, carefully inspect the system to determine the source of the problem. • If the shutdown was a result of a thermal overload condition,
  • Pyle UPLMRA410BT | Instruction Manual - Page 25
    Troubleshooting the R). If the channels which is silent switches to the other side, the problem is either in the signal source (head unit) or the other connecting cables. spark plugs and wires, or that the ignition is in need of service. Check the routing of the speaker and input wires to make sure
  • Pyle UPLMRA410BT | Instruction Manual - Page 26
    Pyle Elite Series - Models & Specs Elite Series Waterproof Amplifiers
  • Pyle UPLMRA410BT | Instruction Manual - Page 27
    Elite Series Waterproof Amplifiers
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27