Ryobi A99HPR1 Operation Manual
Ryobi A99HPR1 Manual
 |
View all Ryobi A99HPR1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ryobi A99HPR1 manual content summary:
- Ryobi A99HPR1 | Operation Manual - Page 1
: To reduce the risk of injury, do not attempt to use this product until you have read thoroughly and understand completely this operator's manual. Ensure compatibility and fit before using this accessory. Do not use this accessory if a part is damaged or missing. REMOVING/INSTALLING HINGE PINS - Ryobi A99HPR1 | Operation Manual - Page 2
ées fixées ensemble par une cheville et de fermer la porte. MANUAL DEL OPERADOR EXTRACTOR/INSTALADOR DE PASADOR de bisagra. Use este producto para la usar este producto sin antes haber leído y comprendido por completo este manual del allá de la base de la bisagra, inserte el perno en la
-
1 -
2
 |
 |
OPERATOR’S MANUAL
HINGE PIN REMOVER/INSTALLER
A99HPR1
ONE WORLD TECHNOLOGIES, INC.
P.O. Box 1288, Anderson, SC 29622
1-800-525-2579 •
www.ryobitools.com
A
B
A - Punch (poinçon, perno)
B - Strike plate (plaque d’impact, placa de impacto)
C - Contact surface (surface de contact, superficie de
contacto)
A - Hinge pin (cheville de charnière,
pasador de bisagra)
A - Hinge pin (cheville de charnière,
pasador de bisagra)
A - Hinge (charnière, bisagra)
B - Hinge pin (cheville de
charnière, pasador de
bisagra)
C - Punch (poinçon, perno)
A - Hinge (charnière, bisagra)
Fig. 1
Fig. 2
Fig. 4
Fig. 3
Fig. 5
WARNING:
To reduce the risk of injury, do not attempt
to use this product until you have read
thoroughly and understand completely this
operator’s manual. Ensure compatibility and
fit before using this accessory. Do not use this
accessory if a part is damaged or missing.
REMOVING/INSTALLING HINGE PINS
See Figure 1 - 5.
A typical door hinge has two interlocking hinge
plates secured together by a hinge pin. Use this
product to install or remove the hinge pin.
To remove a hinge pin:
With the punch facing up, slide the product
onto the base of the hinge
until the punch
contacts the bottom of the hinge pin (see
figures 1 and 3).
NOTE:
If the hinge pin does not extend past
the base of the hinge, insert the punch into
the hinge until it contacts the pin.
Using a hammer, forcefully tap the strike plate
until the punch pushes the head of the pin out
of the hinge.
Slide the product down so that the punch is
no longer inside the hinge.
Hold the product at an angle with the tip under
the head of the hinge pin (see figure 4).
B
C
A
A
C
Continue tapping the strike plate until the pin
is completely removed from the hinge.
NOTE:
Be careful. The door could move
unexpectedly after the pin is removed.
To install a hinge pin:
Align the interlocking parts of the hinge plates.
Slide the hinge pin into the hinge plates until
resistance is felt.
With the punch facing down, slide the product
onto the top of the hinge until the contact
surface is touching the head of the hinge pin
(see figures 1 and 5).
Using a hammer, forcefully tap the strike plate
until the contact surface pushes the pin inside
of the hinge.
NOTE:
Ensure the pin is flush with the top of
the hinge before attempting to open and close
the door.
A
A