Ryobi RY31SC01 Operation Manual
Ryobi RY31SC01 Manual
 |
View all Ryobi RY31SC01 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ryobi RY31SC01 manual content summary:
- Ryobi RY31SC01 | Operation Manual - Page 1
in. Surface Cleaner Attachment RY31SC01 WARNING: To reduce the risk of injury, user must read and understand the operator's manual for their pressure washer these instructions. Refer to them frequently and use them to instruct other users. If you loan someone this tool, loan them these instructions - Ryobi RY31SC01 | Operation Manual - Page 2
filter clockwise until it can no longer be seen over the top of the inlet plug. REPLACEMENT PARTS The following replacement parts may be ordered by calling our customer service department at 1-800-860-4050: Inlet Plug 678557001 High Pressure Filter 308103010 Nozzle Cleaning Tool 678775002 Brush - Ryobi RY31SC01 | Operation Manual - Page 3
de 381 mm (15 po) pour nettoyeur de surface RY31SC01 AVERTISSEMENT : Pour réduire les risques de blessure, l' les autres utilisateurs. Si cet outil est prêté, il doit être accompagné de ces instructions. FICHE TECHNIQUE Connexions Raccord rapide de 6,35 mm (1/4 po) Largeur du plateau 381 - Ryobi RY31SC01 | Operation Manual - Page 4
connecteur. PIÈCES DE REMPLACEMENT Il est possible de commander les pièces de remplacement suivantes en communiquant par téléphone avec le service à la clientèle au 1-800-860-4050. Connecteur 678557001 Filtre haute pression 308103010 Nettoyer les buses 678775002 Jupe de brosse 518752016 BARRE - Ryobi RY31SC01 | Operation Manual - Page 5
Accesorio para limpiador de superficie de 381 mm (15 pulg.) RY31SC01 ADVERTENCIA: Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador de la lavadora de presión antes de usar este accesorio. Para reducir el riesgo de lesiones o daños a la propiedad, rocíe el - Ryobi RY31SC01 | Operation Manual - Page 6
(no incluido). n Con un destornillador de cabeza plana, gire el filtro hacia la derecha hasta que ya no se pueda ver por encima de la parte superior del tapón de la entrada. PIEZAS DE REPUESTO Las siguientes piezas de repuesto pueden solicitarse si se comunica con nuestro departamento de servicio de
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
15 in. Surface Cleaner Attachment
RY31SC01
WARNING:
To reduce the risk of injury, user must read and under-
stand the operator’s manual for their pressure washer
before using this accessory. To reduce the risk of injury
or property damage, spray the pressure stream in a safe
direction to ensure proper connection of all accessories
before starting any cleaning project. Fits most pressure
washers. Ensure compatibility and proper fit before us-
ing this accessory. Wear eye protection with side shields
marked to comply with ANSI Z87.1. Risk of fluid injec-
tions; do not point at people, pets, electrical devices
or the unit itself. Turn off the pressure washer before
changing or adjusting accessories. For cold water use
only.
Save these instructions. Refer to them frequently
and use them to instruct other users. If you loan someone
this tool, loan them these instructions also.
PRODUCT SPECIFICATIONS
Connections
.............................
1/4 in. Quick Connect Plug
Deck Width
.................................................................
15 in.
Maximum Pressure
................................................
3300 psi
Maximum Water Flow
................................................
3 gpm
Maximum Water Temperature
....................................
140°F
INSTALLING THE SURFACE CLEANER ON
THE SPRAY WAND
See Figure 1.
n
Insert the surface cleaner inlet plug into the spray wand
quick connect coupler and secure.
WARNING:
To reduce the risk of injection or injury, only use the sur-
face cleaner on flat, horizontal surfaces. Never lift the
surface cleaner from the cleaning surface while operating
the pressure washer.
USING THE SURFACE CLEANER
See Figure 2.
n
Start the pressure washer as described in your pressure
washer manual.
n
Walk slowly behind the cleaning deck, cleaning as you
go.
NOTE:
If striping or swirling occurs, slow your pace. If
striping or swirling continues, the surface cleaner nozzle(s)
may be clogged. See
Nozzle Maintenance
for how to
clean the nozzles.
Fig. 1
INLET
PLUG
Fig. 2
QUICK CONNECT
COUPLER
WARNING:
Striking any raised obstacle while using the surface
cleaner will damage the unit. If contact does occur and
causes vibration when operating the pressure washer,
stop and discontinue use. Continuing to operate the unit
could result in serious injury or damage to the unit.