Ryobi RYi1000 User Manual 2

WARNING:

This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to

the operator’s manual.

RYi2200A_G QUICK REFERENCE GUIDE

1

1

Connect devices to be powered by generator by following the steps below

(see pages 8-9).

•

Make sure the generator can supply enough continuous (running) and surge (starting) watts for the items you

will power at the same time. See page 8 for how to calculate total amount of power needed.

•

Start the generator with nothing connected.

•

Plug in and turn on the first load, preferably the largest load you have.

•

Permit the generator output to stabilize (engine runs smoothly and attached device operates properly).

•

Plug in and turn on the next load.

•

Again, permit the generator to stabilize.

•

Repeat previous two steps for each additional load.

IMPORTANT: Never add more loads than the generator capacity. Take special care to consider surge loads in

generator capacity.

(See pages 8-9.)

1

WARNING:

Do not connect to a building’s electrical

system unless the generator and transfer

switch have been properly installed and

the electrical output has been verified by

a qualified electrician. The connection

must isolate the generator power from

utility power and must comply with all

applicable laws and electrical codes.

Only use OUTSIDE and

far away from windows,

doors, and vents.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

Pull the starter grip until the engine runs

(see page

14).

When preparing to store the generator, allow the unit to cool for 30 minutes, then follow the guidelines listed on

page 18.

1

Make the most of your purchase! Go to

www.ryobitools.com and register your new tool online.

For questions about operating or maintaining

your product, please call 1-800-860-4050.

Add entire bottle of lubricant provided to the

generator

(see page 13).

5

Slide engine/choke lever to the start (center) position

(see page 14).

6

991000451

3-26-15 (REV:01)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will not start.

Engine switch is off.

No fuel.

Stale gasoline or water in gasoline.

Lubricant level is low.

Spark plug faulty, fouled, or improperly

gapped.

Choke lever is in RUN position.

Engine stored without treating or draining

gasoline, or refueled with bad gasoline.

Dirty fuel filter.

Turn engine switch to ON.

Fill fuel tank.

Drain entire system and refill with fresh fuel.

Engine is equipped with Low Oil Shutoff. If

engine lubricant level is low, it must be filled

before unit will start. Check engine lubricant

level and fill, if necessary.

Replace spark plug.

Move choke lever to START position.

Drain fuel and carburetor. Refuel with fresh

gasoline.

Contact a qualified service center.

Engine hard to start.

Water in gasoline.

Weak spark at spark plug.

Drain entire system and refill with fresh fuel.

Contact a qualified service center.

Engine lacks power.

Dirty air filter.

Engine stored without treating or draining

gasoline, or refueled with bad gasoline.

Check air filter element. Clean or replace as

needed.

Drain fuel and carburetor. Refuel with fresh

gasoline.

AC receptacle does not work.

Circuit breaker is off.

Item plugged in is defective.

Turn ON the AC circuit breaker.

Try a different item.

DC receptacle does not work.

Circuit protector engaged.

Item plugged in is defective.

Remove any load from the generator. Turn the

auto/idle switch to OFF (O), then depress the

DC circuit breaker.

Try a different item.

Generator makes a “spark knock” or “ping-

ing” noise.

An occasional light “knocking” or “pinging”

under heavy load is not a cause for concern.

However, if the knocking or pinging occurs

under normal load at a steady engine speed,

the problem may be with the brand of gasoline

being used.

Switch to a different brand of gasoline, mak-

ing sure that the octane rating is 86 or higher.

If problem continues, contact a qualified

service center.

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the

Maintenance

section It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing to

perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause irreversible

engine damage and/or void your warranty.

FIRST TIME STARTING THE UNIT

STOPPING THE UNIT

IMPORTANT!

FIRST TIME STARTING THE UNIT (CONTINUED)

USING THE GENERATOR

TROUBLESHOOTING

7

Allow engine to run for 15-30 seconds, then move choke to run position

(see page 14).

15-30 S

Place engine/choke lever to the off position (see page 14).

STORING THE UNIT

2

Add fuel

(see page 13).

Slowly pull the recoil grip five (5) times to prime

the fuel system.

(See page 14.)

3

Press the auto idle switch to the OFF position.

(See page 14.)

4

NOTICE:

Do not use E15 or E85 fuel in this product. It is a

violation of federal law and will damage the unit

and void your warranty. Only use unleaded gaso-

line containing up to 10% ethanol.