Ryobi TS1143L User Manual 9

Ryobi TS1143L Manual

Get Ryobi TS1143L PDF manuals and user guides View all Ryobi TS1143L manuals
Add to My Manuals
Save this manual to your list of manuals

Ryobi TS1143L manual content summary:

  • Ryobi TS1143L | User Manual 9 - Page 1
    OPERATOR'S MANUAL 10 in. Compound Miter Saw TS1342L - Double Insulated Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To
  • Ryobi TS1143L | User Manual 9 - Page 2
    this warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool or requested warranty service, you must present proof of purchase
  • Ryobi TS1143L | User Manual 9 - Page 3
    and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.  USE THE RIGHT DIRECTION OF FEED. Feed work into a blade, cutter, or sanding spindle against the
  • Ryobi TS1143L | User Manual 9 - Page 4
    .  When servicing use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.  Use only recommended accessories listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use
  • Ryobi TS1143L | User Manual 9 - Page 5
    unplug tool as applicable) before changing blade or servicing. h) No load speed.  AVOID direct eye exposure when using the laser guide.  This saw can tip over if the saw head is released suddenly and the saw is not secured to a work surface. ALWAYS secure this saw to a stable work surface before
  • Ryobi TS1143L | User Manual 9 - Page 6
    interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts . To reduce the risk of injury, user must read and understand operator's manual before using this product. Always wear safety goggles or safety glasses with side
  • Ryobi TS1143L | User Manual 9 - Page 7
    CENTER for repair. When servicing, use only identical replacement parts. WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. If you do not understand the warnings and instructions in the operator
  • Ryobi TS1143L | User Manual 9 - Page 8
    and should be performed only by a qualified service technician. For service, we suggest you return the tool to the nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELECTRICAL CONNECTION This tool has a precision-built electric motor. It
  • Ryobi TS1143L | User Manual 9 - Page 9
    blade or cutting tool is mounted. Bevel Cut A cutting operation made with the blade at any angle other than 90° to the table surface. Chamfer A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90°. Compound Cut A cross cut made with both a miter and a bevel
  • Ryobi TS1143L | User Manual 9 - Page 10
    Upper Blade Guard "D" Handle DUST BAG Bevel Lock Knob Bevel Scale MITER Fence Miter Table BASE Switch Trigger Lower blade guard throat plate "NO HANDS ZONE" LABEL "NO HANDS ZONE" BOUNDARY LINE Miter Scale MITER LOCK PLATE CONTROL ARM Positive Stop(s) WORK CLAMP 10 Miter Lock Handle
  • Ryobi TS1143L | User Manual 9 - Page 11
    miter saw. When used properly, the laser guide makes accurate, precision cutting simple and easy. MITER FENCE The miter fence on the compound miter saw has been provided to hold the workpiece securely against when making all cuts. The left side is also larger providing additional support. 11 Saw
  • Ryobi TS1143L | User Manual 9 - Page 12
    both the left and right side of the miter table. SELF-RETRACTING LOWER BLADE GUARD The lower blade guard is made of shock-resistant, seethrough plastic that provides protection from each side of the blade. It retracts over the upper blade guard as the saw is lowered into the workpiece. SPINDLE LOCK
  • Ryobi TS1143L | User Manual 9 - Page 13
    LOOSE PARTS The following items are included with the tool:  Miter Lock Handle  Dust Bag  Work Clamp DUST BAG  Blade Wrench  Operator's Manual MITER LOCK HANDLE BLADE WRENCH WORK CLAMP Fig. 6 WARNING: The use of attachments or accessories not listed might be hazardous and could cause
  • Ryobi TS1143L | User Manual 9 - Page 14
    compound miter saw without checking for interference between the blade and the miter fence. Damage could result to the blade if it strikes the miter fence during operation of the saw. WARNING: This saw can tip over if the saw head is released suddenly and the saw is not secured to a work surface
  • Ryobi TS1143L | User Manual 9 - Page 15
    reverse the above procedure. WORK CLAMP See Figure 10. The work clamp provides greater control by clamping the workpiece to the fence or the saw table. It also prevents the workpiece from creeping toward the saw blade. This is very helpful when cutting compound miters. Depending on the cutting
  • Ryobi TS1143L | User Manual 9 - Page 16
    rotating. Installing / replacing the Blade See Figures 11 - 12. WARNING: A 10 in. blade is the required blade capacity of the saw. Never use a Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 12.  Replace laser guide.
  • Ryobi TS1143L | User Manual 9 - Page 17
    .  With the saw blade in the uppermost position, align the laser line with your mark work surface. Practice will teach you the correct position for aligning the laser line with your mark. blade BOLT (hex. hd) LASER GUIDE Blade SCREW Blade Blade BOLT cover Inner Blade Washer Lower blade guard
  • Ryobi TS1143L | User Manual 9 - Page 18
    in this manual show only portions of the compound miter saw. This is intentional so that we can clearly show points being made in the illustrations. Never operate the saw without all guards securely in place and in good operating condition. SQUARING THE MITER TABLE TO THE FENCE See Figures
  • Ryobi TS1143L | User Manual 9 - Page 19
    lock handle.  Lay a framing square flat on the miter table. Place one leg of the square against the fence. Slide the other leg of the square against the flat part of saw blade. Note: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.  The edge of the square
  • Ryobi TS1143L | User Manual 9 - Page 20
    .  Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.  Place a combination square against the miter table and the flat part of saw blade. Note: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.  Rotate
  • Ryobi TS1143L | User Manual 9 - Page 21
    with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. CUTTING WITH YOUR Compound MITER SAW WARNING: When using a work clamp or C-clamp to secure the workpiece, clamp workpiece on one side of the
  • Ryobi TS1143L | User Manual 9 - Page 22
    one of the built-in positive stop notches, located in the miter table frame.  Tighten the miter lock handle securely.  The 45° triangle on the miter fence provides for the maximum clearance required for adjusting the miter saw's angle when making a bevel or compound cut. WORK CLAMP Fig. 27 22
  • Ryobi TS1143L | User Manual 9 - Page 23
    lock plate will seat itself in one of the positive stop notches, located in miter table frame. Compound Miter Cut WORK CLAMP Fig. 28  Tighten the miter lock handle securely.  Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.  Bevel angles can be set from
  • Ryobi TS1143L | User Manual 9 - Page 24
    be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and work table during the cutting operation. Use the optional work clamp or a C-clamp to secure the workpiece. 45° x 45° COMPOUND MITER CUT Fig. 29 Long workpiece Workpiece
  • Ryobi TS1143L | User Manual 9 - Page 25
    COMPOUND MITERS To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound 35.90° B- 3.53° B- 2.94° M- 44.56° M- 35.58° B- 7.05° B- 5.86° M- 44.01° M- 35.06° B- 10.55° B- 8.75° M- 43.22° M- 34.32° B- 14.00° B- 11.60° M- 42.19° M- 33.36° B- 17.39°
  • Ryobi TS1143L | User Manual 9 - Page 26
    is placed flat on the miter table using the compound features of your miter saw. 52° 38° ceiling w a l l Fence inside corner Top edge against fence = LEFT SIDE, INSIDE CORNER RIGHT SIDE, OUTSIDE CORNER MITER Table Fence outside corner BOTTOM edge against fence = RIGHT SIDE, INSIDE CORNER
  • Ryobi TS1143L | User Manual 9 - Page 27
    material, always make sure it is positioned on the miter table with the convex side against the fence as shown in figure 32. If the warped material the fence. clamping wide workpieces See Figure 34. When cutting wide workpieces, such as 2 in. x 6 in., boards should be clamped with a C-clamp as
  • Ryobi TS1143L | User Manual 9 - Page 28
    RYOBI AUTHORIZED SERVICE CENTER. DEPTH STOP The depth stop limits the blade's downward travel. It allows the blade to go below the miter table enough to maintain full cutting capacities. The depth stop is factory set to provide maximum cutting capacity for the 10 in. blade provided with the saw
  • Ryobi TS1143L | User Manual 9 - Page 29
    MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. Brush Cap Brush Assembly WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If
  • Ryobi TS1143L | User Manual 9 - Page 30
    is activated by means of a centrifugal switch only while the saw motor is running and the laser guide is mounted on the saw.  After cleaning the laser guide and replacing the batteries, secure the laser guide cover to laser guide support using the two screws. For proper assembly, be sure to align
  • Ryobi TS1143L | User Manual 9 - Page 31
    NOTES 31
  • Ryobi TS1143L | User Manual 9 - Page 32
    OPERATOR'S MANUAL 10 in. Compound Miter Saw TS1342L - Double Insulated WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
10 in. Compound Miter Saw
TS1342L - Double Insulated
Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.