Samsung DV42H5200GW/A3 Trouble Shooting Guide Tech Manual (English, French, Sp
Samsung DV42H5200GW/A3 Manual
View all Samsung DV42H5200GW/A3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Samsung DV42H5200GW/A3 manual content summary:
- Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 1
, operating, testing, troubleshooting, and disassembly instructions. CAUTION All safety information must be followed as provided in Service Manual of DV45H*, DV42H*. WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 2
is very low or high. dE Running the dryer with door Problem (Communication Error) Check for: - Check PCB and Wire harness. - Replace PCB. EEE Invalid state of Eeprom communication Check for : - PCB with Eeprom circuit. HE Invalid heating Temp in running the dryer Call customer service - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 3
clog up - Display Mode 8 : Average touch sensor data for 1 minute - Display Mode 9 : cycle count Smart Install This allows service personnel to check if the dryer is installed properly. To enter this mode Turn on the product, and press and hold the Adjust Time Up + Temp key for 7 seconds. A message - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 4
micom dry machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 5
5ohms between pin #4 and 5. 2 Motor runs/ tumbler will not turn • • • Belt off or broken/damaged. Idler tension spring too weak or stretched. Idler pulley jammed or stuck. • Lint buildup around drive motor. 3 Runs a few minutes and then stops • • Low voltage present. Blower impeller blocked - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 6
or death; disconnect power to dryer before servicing, unless testing requires power. No Problem 8 The igniter does not glow 9 Igniter glows - No gas ignition The gas is ignited 10 but the flame goes out Improper drying 11 clothes wrinkled Rough texture long dry time 12 Noisy and/Or - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 7
injury or death; disconnect power to dryer before servicing, unless testing requires power. COMPONENT TESTING PROCEDURES Component Electrical Testing (with ohmmeter) Thermistor resistance 10K Ω @ 25°C 77°F Thermostat 1 resistance < 1Ω Belt Cut-off S/W - Lever open: Resistance value - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 8
TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. THERMISTOR 238.23Ω @ 25 °C 77 GAS MODEL Radiant Sensor(10RS) Resistance value < 1 Ω If resistance is infinite, replace Radiant sensor Gas - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 9
TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Sensor Bars & temperature sensor check Sensor Bars - Disconnect harness and test Pink wire Pin 4 to Orange wire Pin 5. Approx ∞ Ω without - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 10
TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, 3-wire, the ground strap must be reconnected to the terminal block support to ground the Dryer frame to the neutral conductor. 4-WIRE system connections A. External ground - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 11
WIRING DIAGRAM WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. WIRING DIAGRAM DV45H6300E*, DV42H5600E* DV45H6300G*, DV42H5600G* 11 Technical_information-03382A_EN_131209.indd 11 2013-12-09 �� 5:37:45 - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 12
WIRING DIAGRAM WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. WIRING DIAGRAM DV42H5400*, DV42H5200*, DV42H5000* 12 Technical_information-03382A_EN_131209.indd 12 2013-12-09 �� 5:37:45 - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 13
les opérations d'entretien ou de réparation de cet appareil. • Reportez-vous au manuel de réparation (DV45H*, DV42H*) pour connaître les consignes d'installation, d'utilisation, de test, de dépannage et de démontage détaillées. ATTENTION Toutes les consignes de sécurité figurant dans le manuel de - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 14
carte de circuit imprimé et le faisceau électrique. - Remplacez la carte de circuit imprimé. Diagnostic possible : - Carte de circuit imprimé avec circuit Eeprom. Appelez le service de dépannage. 2 Technical_information-03382A_CFR_131210.indd 2 2013-12-10 �� 11:56:29 - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 15
Installation intelligente), mettez l'appareil hors tension. Mode Rappel d'erreur Le mode Error Recall (Rappel d'erreur) permet de rappeler aux utilisateurs la dernière erreur qui s'est affichée. Appuyez et maintenez les touches Wrinkle prevent + Dry Level (Anti-froissage + Niveau de séchage) pendant - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 16
est configuré pour une structure complexe, c'est pourquoi il est conseillé de contacter le service après-vente. Les informations suivantes répondent à un diagnostic précis et constituent un guide de réparation adapté. Consignes à respecter pendant les opérations de réparation et de remplacement - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 17
DÉPANNAGE AVERTISSEMENT Afin d'éviter tout risque d'électrocution légère ou mortelle, débranchez le sèche-linge avant de le réparer, sauf si le test nécessite sa mise sous tension. N° Problème Procédure à suivre 1 Ne démarre pas ou ne fonctionne pas • Tous les câbles sont branchés sur leurs - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 18
à peluches est sale. • Le système d'aération est bouché. • Le registre du système d'aération extérieur est bloqué. • Le conduit d'évacuation flexible installé est trop long, possède de trop nombreux coudes. • La prise d'air du sèche-linge est mauvaise. • La vitesse du tambour est incorrecte. La - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 19
Borne : « COM » - « NC » (1-3) : ∞ Ω Borne : « COM » - « NO » (1-2) < 1 Ω Moteur (électronique et gaz) Contacts Fonction 1M 2M 3M 5M 6M Départ Fonctionnement = contact fermé Interrupteur centrifuge (moteur) 2,88 Ω entre les broches 3 et 4 3,5 Ω entre les broches 4 et 5 7 Technical_information - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 20
DÉPANNAGE AVERTISSEMENT Afin d'éviter tout risque d'électrocution légère ou mortelle, débranchez le sèche-linge avant de le réparer, sauf si le test nécessite sa mise sous tension. THERMISTANCE 238,23 Ω à 25 °C 77 °F MODÈLE À GAZ Capteur radiant (10RS) Valeur ohmique < 1 Ω Si la résistance est - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 21
DÉPANNAGE AVERTISSEMENT Afin d'éviter tout risque d'électrocution légère ou mortelle, débranchez le sèche-linge avant de le réparer, sauf si le test nécessite sa mise sous tension. Vérification des capteurs et du capteur de température Capteurs - Débranchez le faisceau et testez le fil rose au - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 22
. Lors de la conversion d'un système électrique à 4 fils en système électrique à 3 fils, le conducteur de terre doit être rebranché sur le support du bornier, pour mettre le châssis du sèche-linge à la terre sur le conducteur neutre. Branchements à 4 FILS A. Connecteur de terre externe B. Fil vert - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 23
SCHÉMA DE CÂBLAGE AVERTISSEMENT Afin d'éviter tout risque d'électrocution légère ou mortelle, débranchez le sèche-linge avant de le réparer, sauf si le test nécessite sa mise sous tension. SCHÉMA DE CÂBLAGE DV45H6300E*, DV42H5600E* DV45H6300G*, DV42H5600G* 11 Technical_information-03382A_CFR_131210 - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 24
SCHÉMA DE CÂBLAGE AVERTISSEMENT Afin d'éviter tout risque d'électrocution légère ou mortelle, débranchez le sèche-linge avant de le réparer, sauf si le test nécessite sa mise sous tension. SCHÉMA DE CÂBLAGE DV42H5400*, DV42H5200*, DV42H5000* 12 Technical_information-03382A_CFR_131210.indd 12 2013- - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 25
instalación, funcionamiento, prueba, solución de problemas y desarmado de la unidad. PRECAUCIÓN Toda la información de seguridad debe seguirse conforme al Manual de servicio de DV45H*, DV42H*. ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentaci - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 26
ALINEACIÓN Y AJUSTES ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. CÓDIGOS DE ERROR Y DE DIAGNÓSTICO Cuando ocurre un error suena una melodía - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 27
mostrar "1". Al levantar el paño se muestra "0". 2. Verificación del motor y del calentador Una vez completada la verificación del sensor táctil, se mostró. Mantenga presionadas las teclas Wrinkle prevent (Prevención de arrugas) + Dry Level (Nivel de secado) durante más de 7 segundos para acceder a - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 28
de las piezas. 1) Dado que ciertos componentes electrónicos se dañan con la electricidad estática presente en el cuerpo humano o en las partes de la secadora hechas con resina, aísle su cuerpo o elimine la diferencia de potencial entre el cuerpo humano y la secadora conectando el enchufe del - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 29
es continuo? 4 Quema fusibles o dispara el disyuntor • (Bobinado del rotor, bobinado del estátor, generador) ¿El protector del motor es normal? • Si no encuentra los puntos anteriores, el montaje de la PCB no es correcto. Reemplácela. • Durante el encendido la secadora extraerá X amperios - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 30
use un ohmímetro para verificar: • Sensor de llama abierto • Deflagrador abierto • Bobina de inducción cortocircuitada • Cableado abierto • Interruptor del motor incorrecto (suministro neutro) • Sin alimentación del control (suministro L1) Si el deflagrador calienta pero no se enciende la llama del - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 31
- "NO" (1-2) : ∞ Ω 2) Interruptor puerta: On (Encendido) Terminal: "COM" - "NC" (1-3) : ∞ Ω Terminal: "COM" - "NO" (1-2) < 1Ω Resistencia de la lámpara AZU (+): BLA Motor (Electrónico y GAS) Contactos Función 1M 2M 3M 5M 6M Inicio Funcionamiento = Contacto cerrado Interruptor centrífugo - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 32
SOLUCIÓN DE PROBLEMAS ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. TERMISTOR 238.23 Ω a 25 °C 77 MODELOS A GAS Sensor radiante (10RS) Valor de - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 33
SOLUCIÓN DE PROBLEMAS ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. Verificación de las barras del sensor y el sensor de la temperatura Barras - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 34
SOLUCIÓN DE PROBLEMAS ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. Conexiones de sistemas de 3 CABLES A. Conector a tierra externo B. Cable a - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 35
DIAGRAMA DEL CABLEDADO ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. DIAGRAMA DEL CABLEDADO DV45H6300E*, DV42H5600E* DV45H6300G*, DV42H5600G* - Samsung DV42H5200GW/A3 | Trouble Shooting Guide Tech Manual (English, French, Sp - Page 36
DIAGRAMA DEL CABLEDADO ADVERTENCIA Para evitar riesgos de descarga eléctrica, lesiones o muerte, desconecte el cable de alimentación de la secadora a menos que la prueba del electrodoméstico requiera que este esté enchufado. DIAGRAMA DEL CABLEDADO DV42H5400*, DV42H5200*, DV42H5000* 12
1
CLOTHES DRYER
Technical Information
CAUTION
All safety information must be followed as provided in Service Manual of DV45H*, DV42H*.
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to dryer
before servicing, unless testing requires power.
Code No. : DC68-03382A_EN
IMPORTANT SAFETY NOTICE – “For Technicians only”
This service data sheet is intended for
use by persons having electrical, electronic, and mechanical experience and knowledge at a level
generally considered acceptable in the appliance repair trade. Any attempt to repair a major
appliance may result in personal injury and property damage. The manufacturer or seller cannot
be responsible, nor assume any liability for injury or damage of any kind arising from the use of
this data sheet.
•
Due to possibility of personal injury or property damage, always contact an authorized
technician for servicing or repair of this unit.
•
Refer to Service Manual (DV45H*, DV42H*) for detailed installation, operating, testing,
troubleshooting, and disassembly instructions.
Technical_information-03382A_EN_131209.indd
1
2013-12-09
�� 5:37:30