Sanyo FWSB426F Quick Start Guide

1

Use one of the Connection Methods shown below to Connect the Soundbar to your TV before plugging in

the AC Power cord.

Rear of TV

Most modern digital TV's do not have Red and White Coaxial Analog Audio Outputs, but do have Red and

White Coaxial Analog Audio Inputs.

If you plan to use Red and White Analog Coaxial Cables to Connect

your TV to this Soundbar, please ensure that your TV does indeed have Red and White Coaxial Analog

Audio OUT. Refer to your TV's User Manual for details.

To Connect Soundbar directly to other devices (Blu-ray player, Game System, etc.), see your Device's User Manual.

HEADPHONE

DIGITAL AUDIO

OUT (COAXIAL)

DIGITAL AUDIO

OUT (OPTICAL)

or

or

Digital Audio Coaxial Cable

(not supplied)

Digital Audio Optical Cable

supplied

Line-in Cable

supplied

Rear of Soundbar

Good

Good

Better

Better

Best

Best

2

Connect AC Power cords from Soundbar and Wireless Subwoofer

to an electric outlet.

CONNECT button

- This button is not a Power-On

button.

DO NOT PRESS IT

, if Pressed,

the Bluetooth Connection to the

Soundbar will be disabled. (Refer to

“Troubleshooting” below “No Sound

from Subwoofer” for pairing the Subwoofer.)

LED

3

Turn Soundbar On using Remote

(POWER/Standby)

.

Check the LED lighting sequence when the

Unit is turned On.

- If the Red LED on the Subwoofer lights up, the Unit

is connected to the Subwoofer.

- When the Subwoofer Red LED is blinking, Unit is not

detecting the Subwoofer. (Refer to “Troubleshooting” below

“No Sound from Subwoofer” for pairing the Subwoofer.)

4

The INPUT indicator lights

up when you Select your

connected INPUT

(

e.g. OPT.

(

Orange

)/

COAX.(Green

))

.

- The OPTICAL/COAXIAL INPUT

indicator blinks when the format of

any Input source is not compatible

on this Unit. Check your TV or other

sources are outputting a Digital

Audio output format (Dolby Digital

or LPCM).

NOTE(

S

):

• Make sure the Soundbar is Turned Off when Connecting Cables.

• Check whether all Connection Cables are properly connected.

•

If you Connect from the Headphone Output on the Device’s Source to the Line-Input on the Soundbar, make

sure the Volume of the Headphone Output on the Device’s Source is set to an appropriate mid-level sound.

Setting it too Low will produce weak output from the Soundbar or setting it too High could cause distortion.

• The feet of the Subwoofer cannot be removed. Do not apply force to them.

C

onnections

R

emote

C

ontrol

B

luetooth

S

etting

M

ount

S

oundbar on a

W

all

T

roubleshooting

LINE

USB

OPTICAL/

COAXIAL

AUX

PAIR

Bluetooth

on

Available Devices

SANYO_FWSB426F

Pairing...

Passcode:

0000

© 2016 Funai Electric Co., Ltd.

Printed in China

XHB00UH

★★★★

Problem

Tip

Sound

No Power

•

Unplug AC Power cord from Soundbar and Subwoofer, wait for 20 seconds. Then Plug in the Subwoofer followed

by the Soundbar, immediately turn the Soundbar On using the Remote Control.

No Sound / Distorted sound

• Make sure the TV, other Devices and Soundbar are all Turned On.

• Make sure Unit is Connected to an Audio Output on your Device.

•

Press INPUT source buttons on your Soundbar Remote Control to select the correct Audio Input.

•

Confirm that the Soundbar is not Muted. Press the VOL +/- or MUTE ICON button’s on the Remote to unmute

the Sound .(See ‘Adjust the Volume’ on the Online Owner’s Manual: sanyo-av.com)

• Adjust the Sound Settings on your Connected device.

•

Adjust the Headphone Volume on some TV’s if you connect this Unit to the Headphone jack on your TV using the

Supplied 3.5mm Line-In cable.

•

If Input is Optical Sound make sure that the Optical Cable Connector is completely inserted into the Terminal (Click

Sound heard when properly inserted).

No Sound from Subwoofer

•

Press and Hold CONNECT button on the Rear of the Subwoofer until the Red LED starts blinking fast. Use the

Soundbar Remote Control and put the Soundbar in AUX input, when in AUX input, Press and Hold the PAIR

button on the Remote Control until the AUX and BLUETOOTH LEDs on the Soundbar blink together. At this point

the Soundbar will attempt Pairing with the Subwoofer, if successful, the LED on the Rear of the Subwoofer will

light up solid Red. See the Online Owner’s Manual for details: sanyo-av.com

•

Certain Sound Sources may not contain enough Bass Sound to activate the Subwoofer, try playing Audio with

more Bass.

Echo Sound is heard when both the

TV and Soundbar Sound are On.

•

It is normal for the TV and Soundbar Sounds to have an Echo Sound when both are turned On at the same time.

•

To Eliminate the Echo Sound Turn the Off or Mute the TV Sound.

Intermittent or No Reaction to

the Remote Control.

•

Check the Batteries in Remote Control and make sure they are Inserted properly using + or - symbols.

• Aim Remote at the Center of this Unit.

•

Use a Digital or Phone Camera pointing the Remote Control at the Camera Lens and press any Remote button.

If Remote IR LED(s) flash on Camera Display, then the Remote is Transmitting a Signal.

Some Phone Cameras

have IR filters in their Lens, therefore you will not see the IR LED(s) flash.

•

If your Thumb is used to operate the Remote Control sometimes it may not be fully working when pointed at the

Soundbar, make sure that your Index Finger is Not blocking the IR Signal from the Front of the Remote Control.

Bluetooth

An external Device cannot connect

with the Soundbar via Bluetooth.

•

Confirm that Bluetooth is Enabled on the external Device. See the User Manual on the external Device on how to

enable Bluetooth.

•

Another Bluetooth Device is already connected to the Soundbar. Disconnect the connected Device, then try again.

Unstable connection between the

Bluetooth Device and the Soundbar.

•

The Bluetooth reception may be poor. Confirm that there is no obstacle between the Bluetooth Device and the

Soundbar. If this does not improve the Sound quality, move the Bluetooth Device closer to the Soundbar.

Remote

*

2

V

M

N

0

0

2

4

9

A

*

SOUNDBAR

S

etup

M

anual

SANYO is a registered trademark of SANYO Electric Co., Ltd. and is used by Funai Electric Co., Ltd. and Funai Corporation, Inc.

under license from SANYO Electric Co., Ltd. Any liability related to SANYO products, including design and quality, is the sole

responsibility of Funai Electric Co., Ltd. and Funai Corporation, Inc.

Please contact Funai Corporation, Inc. for any questions or claims related to SANYO products:

sanyo-av.com

1

Press

(Bluetooth Icon) button on the Remote

Control to switch the Soundbar to Bluetooth mode.

2

Turn On your Bluetooth compatible device.

3

On your Bluetooth compatible device search for

r

r

r

r

r

r

a

a

a

a

a

a

a

a

an

an

an

n

n

n

n

n

nd

nd

nd

nd

d

d

d

d

d

d

d

d

d

select “SANYO_FWSB

426

F” to pair (or register

r

r

r)

)

)

)

)

y

y

y

y

y

y

y

y

y

yo

o

o

o

o

o

o

o

o

ou

u

u

u

u

u

u

u

u

r

r

r

r

r

r

Soundbar with your Bluetooth compatible devic

c

c

c

c

c

c

ce

ce

e

e

e

e

e

e

e

e.

.

.

.

•

If a Passcode is requested, enter “0000”.

•

If the Soundbar name does not appear on the

e

e

e

e

e

Bluetooth compatible device, press

button

on

n

n

n

n

n

on the Remote Control.

4

Play music on the connected Bluetooth compatible device.

5

To Exit Bluetooth mode, press another Audio

Input Source button on the Remote Control.

NOTE(

S

):

If reconnecting the Bluetooth device to the Soundbar fails, delete the registered

profile of this Soundbar from the Bluetooth device, then perform pairing again.

This unit can store up to 9 device profiles.

7-1/2"/190mm

9/64"

~

5/32"/3.5

~

4mm

1-3/16"/30mm

5/32"/4mm

Molly Anchor

~3/16"/5 mm’’

~3/8"/9 mm’’

*Unplug the AC Power cord to Turn

Off completely.

1

3

2

(POWER/Standby)

Press to Turn On or Off

(Standby mode)*.

STANDARD

/

SPORTS

/

MUSIC

/

MOVIE

/

NEWS

/

NIGHT

Press to Select desired

Equalizer mode.

VOL

(ume)

Press to adjust Volume

+ (up) / - (down) for Soundbar.

(MUTE)

Press to Mute the Sound

and press again to Unmute

the Sound.

Press to operate the

BLUETOOTH device and

USB Memory Stick (WAV file

Only).

Install 2 AAA (1.5V) batteries (supplied)

Insert Batteries

NOTE(

S

):

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, Li-ion, etc.) batteries.

(Optional-refer to ‘Installing the Soundbar on a wall’ in the Online Owner’s Manual.)

Use the “Wall Mounting Template” at the bottom right of this guide when you make

the screw holes on the wall.

SURROUND

Press to Select Surround

Sound On or Off.

LINE

/

OPT.

(ical) or

COAX.

(ial)

/

/

USB

/

AUX

(iliary)

Press one of the INPUT Buttons

to Select appropriate Source.

See the Online Owner’s Manual for details:

See the Online Owner’s Manual for details:

sanyo-av.com

sanyo-av.com

1

Please visit website

Please visit website

sanyo-av.com

2

Select Download.

3

Type in the Model # “

FWSB426F

”, and click “

Search

”.

4

Sl

t th

M

l

d

li k

“

Select the Manual and click on “

D

l

d

Download

”

”.

Register Online at

sanyo-av.com/support/

today to get the most benefits from your purchase.

Registering your model with SANYO makes you eligible for all of the valuable

benefits such as

software upgrades and important product notifications.

Register Online at

sanyo-av.com/support/

SUPPLIED ACCESSORIES

• Remote Control (NC302UH) and Batteries (AAA, 1.5V x 2)

• Setup Manual

• Digital Audio Optical cable

• Line-In cable

PAIR

(ing)

Press to Start Pairing mode.

3-3/4" (95mm)

3-3/4" (95mm)

Center line

Wall Mounting Template

Sanyo FWSB426F Quick Start Guide

Sanyo FWSB426F Manual

Sanyo FWSB426F manual content summary: