Sanyo PLC-SU31 Owners Manual

Sanyo PLC-SU31 - SVGA LCD Projector Manual

Get Sanyo PLC-SU31 - SVGA LCD Projector PDF manuals and user guides View all Sanyo PLC-SU31 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-SU31 manual content summary:

  • Sanyo PLC-SU31 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-SU31 Owner's Manual
  • Sanyo PLC-SU31 | Owners Manual - Page 2
    EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH
  • Sanyo PLC-SU31 | Owners Manual - Page 3
    , be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the
  • Sanyo PLC-SU31 | Owners Manual - Page 4
    instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers Trade Name Responsible party Address Telephone No. : PLC-SU31 : Sanyo : SANYO the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be
  • Sanyo PLC-SU31 | Owners Manual - Page 5
    AND CLEANING 38 TURNING ON / OFF PROJECTOR 19 CLEANING PROJECTION LENS 38 ADJUSTING SCREEN ZOOM ADJUSTMENT FOCUS ADJUSTMENT 20 20 20 LAMP REPLACEMENT LAMP REPLACE COUNTER TROUBLESHOOTING 39 39 40 KEYSTONE ADJUSTMENT 20 TECHNICAL SPECIFICATIONS 42 PICTURE FREEZE FUNCTION 20 NO SHOW
  • Sanyo PLC-SU31 | Owners Manual - Page 6
    is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed. This projector is shipped with this function ON. N Wireless Mouse Remote Control Unit supplied with this projector has Wireless Mouse function for
  • Sanyo PLC-SU31 | Owners Manual - Page 7
    . This area will become hot while a projector is used. This projector detects internal temperature and automatically controls operating power of Cooling Fans. LENS COVER BACK TOP CONTROLS AND INDICATORS INFRARED REMOTE RECEIVER POWER CORD CONNECTOR BOTTOM LAMP COVER ADJUSTABLE FEET AND FEET LOCK
  • Sanyo PLC-SU31 | Owners Manual - Page 8
    into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.) CAUTION For safety, unplug
  • Sanyo PLC-SU31 | Owners Manual - Page 9
    flat projection surface. G The projector can be focused from 3.0'(0. Lift the front of the projector and pull FEET LOCK LATCHES on the both sides of the projector. 2 Release FEET LOCK retract ADJUSTABLE FEET, lift the front of the projector and pull and undo FEET LOCK LATCHES. Keystone distortion of
  • Sanyo PLC-SU31 | Owners Manual - Page 10
    cabinet, and it is not designed to protect an appliance from external forces. Do not transport a projector through a courier or transport services with this bag. The projector can be damaged. When handling a projector, do not drop, bump, subject it to strong forces or put other things on the cabinet
  • Sanyo PLC-SU31 | Owners Manual - Page 11
    AUDIO IN - L (MONO) Y - Pb / Cb - Pr / Cr S-VIDEO INPUT JACK Connect the S-VIDEO output from video equipment to this jack. (Refer to P13.) USB CONNECTOR (Series B) When controlling the computer with Remote Control Unit of this projector, connect USB port of your personal computer to this connector
  • Sanyo PLC-SU31 | Owners Manual - Page 12
    (MONO) Y - Pb / Cb - Pr / Cr EXT.SP(8Ω) AUDIO IN S - VIDEO (STEREO) COMPUTER USB RESET EXT. SP(8Ω)(STEREO) Audio Cable (stereo) ✽ Audio Input Speaker Terminal External Speaker MONITOR OUT COMPUTER IN CONTROL PORT Terminals of the Projector NOTE : When connecting the cable, the power cords of
  • Sanyo PLC-SU31 | Owners Manual - Page 13
    AUDIO IN - L (MONO) Y - Pb / Cb - Pr / Cr EXT.SP(8Ω) AUDIO IN S - VIDEO (STEREO) COMPUTER USB RESET MONITOR OUT COMPUTER IN CONTROL PORT EXT. SP(8Ω)(STEREO) Audio Cable (Stereo) ✽ Terminals of the Projector Audio Input Speaker Terminal External Speaker NOTE : When connecting the cable, the
  • Sanyo PLC-SU31 | Owners Manual - Page 14
    operation. (P17, 18) MUTE D.ZOOM INPUT MENU ALL-OFF SWITCH When using Remote Control Unit, turn this switch to "ON." And turn it to "ALL OFF" NO SHOW FREEZE AUTO PC ADJ. IMAGE P-TIMER POWER ON-OFF BUTTON Used to turn projector on or off. (P19) INPUT BUTTON Used to select input source. (P22, 30
  • Sanyo PLC-SU31 | Owners Manual - Page 15
    heat. G Do not drop Remote Control Unit. G If a battery has leaked on Remote Control Unit, carefully wipe the case clean and load new batteries. G Danger of explosion if battery is incorrectly replaced. G Dispose of used batteries according to battery manufacturer's instructions and local rules. 15
  • Sanyo PLC-SU31 | Owners Manual - Page 16
    BEFORE OPERATION TOP CONTROLS AND INDICATORS This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top. WARNING TEMP. INDICATOR Flashes red when internal projector temperature is too high. (P38) LAMP REPLACE INDICATOR Turns to yellow when the life of the projection lamp draws to
  • Sanyo PLC-SU31 | Owners Manual - Page 17
    HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through ON-SCREEN MENU. Refer to the following pages to operate each adjustment on ON-SCREEN MENU. 1 DISPLAY MENU Press MENU button to display ON-SCREEN MENU. WIRELESS REMOTE CONTROL POINT BUTTON Used to move the Pointer UP
  • Sanyo PLC-SU31 | Owners Manual - Page 18
    BAR Press MENU BUTTON while connecting to PC input source. GUIDE WINDOW Shows selected item of ONSCREEN MENU. PC SYSTEM MENU Used to change settings of projector or reset Lamp Replace Counter. (Refer to P35, 36) INPUT MENU Used to select input source either Computer or Video. (Refer to P22) PC
  • Sanyo PLC-SU31 | Owners Manual - Page 19
    or Video source appears after 30 seconds. 30 Preparation Display disappears after 30 seconds. TURNING OFF PROJECTOR 1 Press POWER ON-OFF button on Top Control or on Remote Control Unit, and a message "Power off?" appears on a screen. 2 Press POWER ON-OFF button again to turn off projector. LAMP
  • Sanyo PLC-SU31 | Owners Manual - Page 20
    or POINT DOWN button to make image smaller. Zoom Message disappears after 4 seconds. FOCUS ADJUSTMENT 1 Press FOCUS button on Top Control or FOCUS L/M button on Remote Control Unit. The message "Focus" is displayed. 2 Adjust focus of image by pressing FOCUS L/M button or POINT UP/DOWN button
  • Sanyo PLC-SU31 | Owners Manual - Page 21
    to normal, press NO SHOW button again or press any other button. No show Message disappears after 4 seconds. P-TIMER FUNCTION Press P-TIMER button on Remote Control unit. The timer display "00 : 00" appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER
  • Sanyo PLC-SU31 | Owners Manual - Page 22
    DIRECT OPERATION Choose Computer by pressing INPUT button on Top Control or on Remote Control Unit. If projector cannot reproduce proper image, select correct input source through MENU OPERATION (see below). INPUT button Computer Video MENU OPERATION 1 Press MENU button and ON-SCREEN MENU will
  • Sanyo PLC-SU31 | Owners Manual - Page 23
    COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and (Interlace) 60.00 60.00 (Interlace) 60.00 (Interlace) 50.00 (Interlace) NOTE : Specifications are subject to change without notice. 23
  • Sanyo PLC-SU31 | Owners Manual - Page 24
    ADJ. button on Remote Control Unit. Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in PC SYSTEM Menu (P22). Refer to step 3 of MANUAL PC ADJUSTMENT section (P26
  • Sanyo PLC-SU31 | Owners Manual - Page 25
    to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUST Menu cannot be
  • Sanyo PLC-SU31 | Owners Manual - Page 26
    SELECT button at Display area icon and Display area dialog box appears. Display area Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to
  • Sanyo PLC-SU31 | Owners Manual - Page 27
    image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. IMAGE 1~4 User preset picture adjustment in IMAGE
  • Sanyo PLC-SU31 | Owners Manual - Page 28
    0 to 63.) Gamma Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.) 3 Store To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to the Image
  • Sanyo PLC-SU31 | Owners Manual - Page 29
    screen size (800 x 600), this projector enters "Digital zoom +" mode automatically. Wide Provides image to fit wide video aspect ratio (16 : 9) by A projected image can be also expanded by pressing D.ZOOM L button on Remote Control Unit. Digital zoom - When Digital zoom - is selected, ON-SCREEN MENU
  • Sanyo PLC-SU31 | Owners Manual - Page 30
    SELECTING INPUT SOURCE DIRECT OPERATION Choose Video by pressing INPUT button on Top Control or on Remote Control Unit. If projector cannot reproduce proper video source, select correct input source through MENU OPERATION (see below). INPUT button Video Computer MENU OPERATION 1 Press MENU
  • Sanyo PLC-SU31 | Owners Manual - Page 31
    , and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC
  • Sanyo PLC-SU31 | Owners Manual - Page 32
    VIDEO INPUT PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Cinema, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. Standard Normal picture level preset on this projector. Cinema Picture level
  • Sanyo PLC-SU31 | Owners Manual - Page 33
    VIDEO INPUT IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/ obtain better balance of contrast. (From 0 to 15.) NOTE : Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M or PAL-N. Press SELECT button at this icon to store the value. 33
  • Sanyo PLC-SU31 | Owners Manual - Page 34
    be set and then press SELECT button. PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display want to select and then press SELECT button. Normal Provides image at a normal video aspect ratio of 4 : 3. Wide Provides image at a wide screen ratio of
  • Sanyo PLC-SU31 | Owners Manual - Page 35
    UP/DOWN/LEFT/RIGHT button(s). Refer to KEYSTONE ADJUSTMENT on page 20. Blue back When this function is "On," this projector will produce a blue image instead of the video noise on the screen when any input source is unplugged or turned off. When pressing SELECT button at Language, Language Menu
  • Sanyo PLC-SU31 | Owners Manual - Page 36
    code (Code 1), operate both projector and Remote Control in the ways above again. NOTE : When batteries of Remote Control Unit are replaced or ALL- OFF switch is turned to "ALL-OFF," the remote transmit code automatically returns to the normal code (Code 1). Lamp counter reset This function is used
  • Sanyo PLC-SU31 | Owners Manual - Page 37
    of your computer to Control Port of the projector with Control Cable for Serial Port (not supplied). OPERATING WIRELESS MOUSE When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on Wireless Remote Control Unit. POINT button Used
  • Sanyo PLC-SU31 | Owners Manual - Page 38
    and particles. 4 Replace Air Filter properly. Make sure that Air Filter is fully inserted. CAUTION Do not operate the projector with Air Filter the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING PROJECTION LENS Follow these steps
  • Sanyo PLC-SU31 | Owners Manual - Page 39
    No. of your projector : PLC-SU31 G Replacement Lamp Type No. : POA-LMP35 (Service Parts No. 610 293 2751) LAMP REPLACE COUNTER Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting. 1 Turn projector on, press
  • Sanyo PLC-SU31 | Owners Manual - Page 40
    APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check the items below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13. 2. Check cable connection
  • Sanyo PLC-SU31 | Owners Manual - Page 41
    . WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain about the
  • Sanyo PLC-SU31 | Owners Manual - Page 42
    TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System High Definition TV Signal Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Projection Lens Throw Distance Projection Lamp Video Input
  • Sanyo PLC-SU31 | Owners Manual - Page 43
    port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable. (Control Cable for PS/2 port is supplied, and Control Cables for Serial port and ADB port are not supplied.) Pin Configuration 876 5 43 21 PS/2 Serial ADB 1 ----- R X D ----- 2 CLK ----- ADB 3 DATA
  • Sanyo PLC-SU31 | Owners Manual - Page 44
    Printed in Japan Part No. 610 297 6700 (1AA6P1P3096-- ME8A) SANYO Electric Co., Ltd
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Owner’s Manual
PLC-SU31
Multimedia Projector
MODEL