Sanyo PLC-WL2500 Owner's Manual _ Network
Sanyo PLC-WL2500 - 2500 Lumens Manual
 |
UPC - 086483078859
View all Sanyo PLC-WL2500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-WL2500 manual content summary:
- Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 1
This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 2
Communications Commission Notice This equipment has been tested and found to comply with the limits instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-WL2500 Trade Name : Sanyo Responsible party : SANYO - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 4
Table of contents Compliance...2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9 Chapter 2 Setup Procedures 11 Connecting to the LAN line...12 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 5
Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 6
sends mes- sages to the registered e-mail PC1 PC2 addresses when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You can take efficient action for quick recovery. PJ2 PJ1 PC5 Turn ON PJ2 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 7
512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of colors: Either of projector. If you do not use the function E-mail Alert, this application is not required. Network specifications of the projector - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 8
from the actual operation depending on your computer environment. Use of this manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 9
pp.11-16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projectors, then start browser configurations. ➔ "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 10
Chapter 1 Preparation 10 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 11
Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 12
ed but- tons. Then the Menu will disappear, the "Please wait..." message will appear, and switching operation will start. Switching will take a while and the projector's LINK/ACT Lamp will be on or blink, and after completing the operation, the "Please wait..." message will disappear. 12 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 13
DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 14
"0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 15
Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 16
Chapter 2 Setup Procedures Wired LAN factory default settings Parameter LAN 1 SELECTED LAN LAN 2 LAN 3 DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 17
Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 18
Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 20
3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 21
Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 22
display the initial setting page. Item Description Language Switches display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 23
What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input Computer 1 Computer 2 HDMI Video - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 24
in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. * The numerical - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 25
an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and Enter e-mail address of the user to send mail when the projector has an abnormality. SMTP Authentication setting Auth Sets authentication setting option - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 26
setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 27
off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 28
once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information. ● When PJ lamp replacement time is reached: TITLE: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 29
SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 30
off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 31
Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 32
Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 33
standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 34
pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function projector. Source Selects signal source of the input. Computer1 : RGB Component RGB(Scart) Computer2 : RGB HDMI - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 35
of signal input to the projector. The available system mode computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are 720p, 1035i and 1080i. Available selection at the HDMI input Item Description D-XGA It automatically switches to the proper computer system of - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 36
Chapter 4 Controlling the Projector Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speaker. (0 ~ 63) Mute Suppresses the sound. (ON, OFF) 36 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 37
Control Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast Adjusts picture contrast (0~ 63) Brightness Adjusts picture - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 38
function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 which are the customized mode created by using - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 39
the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item Description Screen Switches the screen mode. (Normal, True, Full, Wide, Zoom - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 40
Sets the language display of projector's on-screen display menu. Auto the screen during the startup. (OFF, Default, User) Setting 2 Item Description Ceiling Sets the image top/bottom and left/ right reversed. (ON, OFF) Rear . OFF) Lamp control......Selects lamp control mode. (Normal, Eco) 40 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 41
lock Sets the prohibition of controls either Projector or Remote control. (OFF, Projector keys, Remote control) Fan control Sets the fan control speed. OFF Normal mode ON1 Highland mode 1 ON2 Highland mode 2 Lamp Corres. Value(h Displays the lamp use time (Corresponding value) . Reset the time - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 42
. Security Displays the security (PIN code lock) status (Yes, No) PJ time(h) Displays the accumulated use time of the projector. Lamp Corres. Value(h) Displays the use time (Corresponding value) of the lamp. Filter time(h) Displays the accumulated use time of the filter. Indication of the - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 43
Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 43 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 44
the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168 - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 45
. Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 46
*1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 47
appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set on C1D menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 48
is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 49
Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 50
proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 51
to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 52
address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 53
of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong access the projector installed on the company's local area network from a remote location? A There are some ways to access to the projector in the - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 54
Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 55
take a lot of time to complete the page display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 56
, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.46 - 47). Q What is the MAC address assigned to - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 57
Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult - Sanyo PLC-WL2500 | Owner's Manual _ Network - Page 58
NETWORK OWNER'S MANUAL SO-KJ8AD SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
 |
 |
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.