Sanyo PLC-WTC500AL Owner's Manual

Sanyo PLC-WTC500AL - 5000 Lumens Manual

Get Sanyo PLC-WTC500AL - 5000 Lumens PDF manuals and user guides
UPC - 086483076442
View all Sanyo PLC-WTC500AL manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-WTC500AL manual content summary:

  • Sanyo PLC-WTC500AL | Owner's Manual - Page 1
    Multimedia Projector MODEL PLC-WTC500AL *Projection lens is optional. Owner's Manual
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 2
    long time. (p.58) ◆ Automatic Filter Replacement Function The projector monitors the condition of the filter and replaces a filter automatically when it detects the clogging. ◆ Power Management The Power management function reduces power consumption and maintains lamp life (p.56). ◆ Picture in
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 3
    Instructions 63 Replacing the Filter Cartridge 64 Resetting the Filter Counter 65 Resetting the Scroll Counter 65 Auto Lamp Selection System 66 Lamp Replacement 67 Warning Indicators 69 Cleaning the Projection Lens 70 Cleaning the Projector Cabinet 70 Appendix 71 Troubleshooting
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 4
    of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 5
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 6
    . The fans' running speed is changed according to the temperature inside the projector. Air flow Exhaust Vent (Hot air exhaust) Air Intake Vent IMPORTANT! Filter Maintenance!! The projector uses a lamp which generates significant heat. The cooling fans and air vents are provided to dissipate
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 7
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 8
    Instructions Moving the Projector Use the hand grip when moving the projector. Replace the lens cap and retract the adjustable feet to prevent damage to the lens and cabinet when carrying. When the projector is not in use for an extended period, put it into a suitable case to protect the projector
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 9
    instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number(s) : PLC-WTC500AL Trade Name : Sanyo Responsible party : SANYO from the Parts Department indicated in your User Instructions. If the plug supplied is not
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 10
    Remote Receiver (Back) !2 Lamp Cover !3 Filter Cover !4 Exhaust Vent CAUTION Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side. ✽Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector. *Kensington is a registered
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 11
    Side Terminal t y u Part Names and Functions q we r i o q HDMI TERMINAL Connect the HDMI signal (including sound signal) from video equipment or the DVI signal from computer to this terminal (p.20). w COMPUTER INPUT TERMINAL (ANALOG) Connect the computer (or RGB scart) output signal to this
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 12
    Part Names and Functions Side Terminal !0 !1 !2 !3 !0 USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with the supplied USB cable (p.20). !1 R/C JACK When using the wired
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 13
    q WARNING TEMP. indicator - Lights red light when the projector detects an abnormal condition or the filter cartridge is not installed. - Blinks red when the internal temperature of the projector exceeds the operating range (pp.69, 79). w LAMP 1 REPLACE indicator Turn yellow when the life of the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 14
    a pointer for the laser light window or a signal is being sent from wireless mouse operation (pp.32-33). the remote control to the projector (p.32). r Laser Light window A laser beam is emitted from here (p.32). !1 INFO. button Display the input source information (p.30). t ON button Turn the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 15
    @3 SHUTTER button Close the built-in shutter for light blocking.(pp.28,58) @4 KEYSTONE button Correct keystone distortion (p.31). @5 LENS SHIFT button Select the Lens Shift function (p.28). @6 SCREEN button Select the screen size (p.30). @7 R-CLICK button Act as the right mouse button for wireless
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 16
    battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared 16.4' (5 m) Remote Receivers) when pressing the buttons. Maximum operating range for the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 17
    or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 55. 1 Press and hold the MENU and a number
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 18
    up to 3.5 degrees with the adjustable feet. Rotate the adjustable feet and tilt the projector to the proper height; to raise the projector, rotate the both feet clockwise. To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise. To correct keystone distortion
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 19
    an optional lens, install the lens by following the instructions below. Ask the sales dealer for detailed information of the optional lens specifications. Removing the lens 1 Shift the lens to the center position by using the Lens shift function (see page 28). 2 Turn off the projector and unplug
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 20
    the Standby mode is set to "Eco" in the Setting, MONITOR OUT and AUDIO OUT are disabled. (p.56) Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. ✔Notes: • When DVI signal is connected to HDMI terminal with HDMI-DVI cable, connect
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 21
    used for connection • Video Cable (RCA x 1) • VGA-Scart Cable • S-VIDEO Cable • BNC Cable • HDMI Cable (Cables are not supplied with the projector.) S-video Output Composite Video Output Digital Output RGB Scart 21-pin Output Refer to the Monitor Out Signal Table (next page). Composite
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 22
    to MONITOR OUT terminal. External Audio Equipment Audio Input Audio cable (stereo) AUDIO OUT (stereo) ✔Notes: • When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available. • When the Standby mode is set to "Eco" in the Setting, MONITOR OUT and AUDIO OUT are disabled. (p.56
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 23
    system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet must be near this equipment and must be easily accessible. ✔Note: •U nplug
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 24
    after 20 seconds. Selected Input Source and Lamp Control Lamp control Lamp status See pages 54,66 for the Lamp control and status. ✔Note: • The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. PIN Code Input Dialog Box After the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 25
    . After it is cooled down completely, unplug the AC power cord. "Power off?" disappears after 4 seconds. TO MAINTAIN LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF. DO NOT UNPLUG THE AC POWER CORD WHILE THE COOLING FANS ARE RUNNING OR BEFORE
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 26
    Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 27
    71-72. *The menu bar displays changes depending on the input signals. Guide Window Show the selected Menu of the OnScreen Menu. System Select a Set the projector's operating configurations (pp.49-62). - Language - Logo - Picture in Picture - Background - Lamp mode - Lamp control - Filter control -
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 28
    Operation Operating with Projector Control Lens Operation The following lens operation can be made with the Lens button on the top control. Press the Lens button to enter each lens operation mode. The selected adjustment display appears on the screen. Zoom ➜ Focus ➜ Lens Shift Zoom Adjustment
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 29
    Sound Adjustment Direct Operation Volume Press the VOLUME+/- buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE button on the remote control to temporarily turn off the sound. To turn the sound
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 30
    and the signal being projected through the projector. Remote Control AUTO PC button D.ZOOM button ZOOM button FREEZE button INFO. button POINT ed buttons SCREEN button LENS SHIFT button Press the INFO. button on the remote control to display the information window on the screen. To hide the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 31
    Basic Operation PIP button Press the PIP button on the remote control to select Picture in Picture or Picture by Picture mode. See page 52 for details. PIP VOL. button Press the PIP VOL. button on the remote control at the PIP mode. The volume dialog box appears. Use the Point 7 8 buttons to adjust
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 32
    Laser pointer has switched to the Pointer, use the LASER button as the Pointer function ON-OFF switch. Press the LASER button pointing toward the projector and see if it lights green. 32 ✔Note: • You can choose the size of Spotlight (Large/Middle/ Small) and the pattern of Pointer (Arrow/Finger
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 33
    Operation The remote control can be used as a wireless mouse for your computer. 1 Before operating the wireless mouse, connect your computer and the projector with the supplied USB cable (p. 20). When the Pointer function is used, the wireless mouse is not available. 2 When a USB cable is connected
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 34
    Input Selection Input Remote Control INPUT buttons Remote Control Operation Press the INPUT 1, INPUT 2, or INPUT 3 buttons on the remote control. The input source appears on the screen as you press each button. Select the connected input source. Top Control INPUT button Remote Control button
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 35
    is connected. Video When the video signal is connected. Component* When the component signal is connected. * If the projector cannot reproduce proper video image, select a system manually (see "Video System Selection" on page 36) *"Component" can accept the component signal and the analog RGB
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 36
    system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 37
    (pp.39-40). ----- There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on page 71.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The adjusted data can be stored in Mode 1-10 (pp.39-40). SVGA
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 38
    parameters The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by function. When the image is not provided properly with this operation, manual adjustments are required (pp.39-40). • The Auto PC Adjustment
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 39
    PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 40
    Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 41
    Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for graphics. (This icon is displayed with video signal.) Image 1-4 For viewing with the user preset image level in the Image Adjust Menu (see page 44). 41
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 42
    Image Adjustment Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 43
    of the following options. Off Disabled. L1 For an active picture. L2 For a still picture. Film For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Image Adjustment ✔Notes: • Progressive cannot be selected when 480p, 575p, or 720p is
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 44
    Image Adjustment Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Store To store the adjusted data, select Store and press the SELECT button. Use the Point ed buttons
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 45
    function is set to "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to "On," the picture is left/right reversed. This function is used to project the image from the rear
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 46
    original image size is larger than the screen size (1280 x 800), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to and press the SELECT button. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 47
    cannot display any resolution higher than 1600 x 1200. If your computer's screen resolution is higher than that, lower the resolution before connecting to the projector. • The image data other than 1280x 800 is modified to fit the screen size in initial mode. • True, Full screen, and Digital zoom
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 48
    center areas. Wide Provide the image at the 16:9 wide screen ratio. Full Provide the full screen image. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the screen for a few seconds and then the Aspect
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 49
    Setting Setting This projector has a Setting menu that allows you to set up the other various functions select This function decides on the starting-up display from among following options. User Show the image you captured Default Show the factory-set logo Off Show the countdown display only Logo
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 50
    projected image. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed the next time you turn on the projector. To cancel the Capture function, select [No]. Capture Select [Yes] to capture the projected image. ✔Notes
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 51
    Setting Enter a Logo PIN code Use the Point ed buttons on the top control or Number buttons on the remote control to enter a number. When using top control Use the Point ed buttons on the top control to select a number. Press the Point 8 button to fix the number and move the red frame pointer to
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 52
    : Select the Sub picture or Main picture. Background The selected background screen will be displayed when no input signal is detected. Blue Project a blue background User Project an image selected in the Logo setting. Black Project a black background ✔Note: • When no captured image is set, the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 53
    recommended total hours of use in the Lamp 1/2 mode, the Lamp mode will be switched to Lamp 1 or Lamp 2 mode automatically. Switching operation is done when the lamp is changed. • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 54
    mode for the used environment. ✔Note: • A lamp is switched to the lamp which is not exceeding the recommended total hours of use next time when you turn on the projector, even when the Mode 1 is selected. Filter control You can replace the filter with this function. Press the SELECT button at
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 55
    (Arrow, Finger, or Dot). (See page 32 for operation.) Pointer Setting Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should be set on both the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 56
    option. Countdown Off Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Hide the On-Screen Displays except; ● On-Screen Menu ● "Power
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 57
    fans will not work properly and that causes malfunctions of the projector and decreases the lamp life. Slant setting +70° Select the projector's installation condition from the following options: UP Off When using the projector within the range of the upward/ downward inclination of ±70º and
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 58
    control. Management The Shutter Management function turns off the projection lamp when the projector is left with the shutter closed and the set time has vary from equipment to equipment. For details, refer to the owner's manual of video equipment. When the black part of the image are destroyed
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 59
    lock and PIN code lock function to set the security for the projector operation. Key lock This function locks the top control and remote wrong with your remote control, contact the dealer where you purchased the projector or the service center. Key lock Select Key lock. Use the Point ed buttons
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 60
    and then move the pointer to "Quit" with the Point d button. Press the SELECT button to close the dialog box. PIN code lock When the projector is locked with a PIN code, the PIN code lock symbol appears on the menu bar. Enter a PIN code After a correct PIN code is entered, the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 61
    can no longer be started. Test pattern Various test pattern are available for use when setting up the projector. Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 62
    the filter use, timer setting option and the Reset options. When the projector reaches a time set in the timer setting, the Filter replacement icon all setting values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, and filter counter to the factory default settings.
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 63
    cause a breakdown. •T he used part of the filter can be seen on the edge of the Filter cartridge after scrolling the filter, but there is no problem for the use of the projector. • Do not use the filter cartridge with other projector. The filter counter and the scroll counter do not recognize
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 64
    cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Replacement filter cartridge can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector PLC-WTC500AL ● Replacement Filter Cartridge Type No. : POA-FIL-100 (Service Parts Code: 610
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 65
    icon. 2 Use the Point ed buttons to move the red frame pointer to Filter counter and then press the SELECT button. A dialog box appears showing the Used . 2 Use the Point ed buttons to move the red frame pointer to Filter counter and then press the SELECT button. A dialog box appears showing the Used
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 66
    Function automatically changes the lighting lamp (Lamp Mode) by detecting the status of lamp. When either of the 2 lamps is out, the projector operates with the other lamp. The Lamp Mode can be switched manually. Refer to the SETTING section on page 53. LAMP 1 MODE When Lamp 1 is burnt out. When
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 67
    to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot. CAUTION For continued safety, replace with a lamp of the same type lamp. Do not drop the lamp or touch the glass bulb! The glass can shatter and may cause injury. CAUTION When
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 68
    give the following information to the dealer. ● Model No. of your projector : PLC-WTC500AL ● Replacement Lamp Type No. : POA-LMP125 (Service Parts No. 610 342 2626) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 69
    of the projector away from the duct or vent. - Is the filter clean? Clean the filter periodically or replace it with a new one. The projector is red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 70
    lens. When the projector is not in use, replace the lens cap. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning. Gently wipe the projector cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 71
    User" or "Off" are not chosen at Logo function. See page 49. the default one. An icon other than Input mode, - That is the Lamp replacement icon or the Filter warning icon. Lamp control or lamp when connecting to the projector See your computer's instruction manual for the setting.
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 72
    LAMP 1/2 REPLACE indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See pages 66-68, 78. - Check the Lamp is distorted. - With maximum lens shift, image distortion may AUDIO OUT is plugged in, the projector's built-in speaker is not
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 73
    lock. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 74
    Appendix Menu Tree Input Input 1 Input 2 Input 3 RGB (PC analog) RGB (Scart) HDMI Quit RGB Video Component Quit Video S-video Quit Go to System (1) Go to System (1) Go to System (1) Go to System (3) Go to System (2) Go to System (3) Go to System (3) System (1) Mode 1 Mode 2 XGA 1 - - - -
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 75
    Ceiling On/Off Rear On/Off Information Input H-sync freq. V-sync freq. Screen Language Lamp mode Lamp control Lamp 1 Lamp 2 Filter counter Power management Shutter management Remote control Projector ( ) Min Security Remote control SERIAL NO. Key lock PIN code lock Sound Volume Mute
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 76
    Lamp mode Blue/User/Black Lamp 1/Lamp 2 Lamp 1/ 2 Timer On/Off Start ( 0- 24 Hour) Lamp interval (1-24 Hour) Quit Lamp control Lamp control Auto 1/Auto 2/High /Normal/Eco 1/Eco 2 Lamp life control Filter log Filter counter Factory default Quit Key lock Off Projector (all) Projector (part
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 77
    is operating normally. Indicators POWER green / red WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP 1/2 REP. yellow Projector Condition The projector is off. (The AC power cord is unplugged.) The projector is in stand-by mode. Press the ON/STAND- red ✽ ✽ ✽ ✽ BY button
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 78
    returns to normal. When turning on the projector, the WARNING TEMP. indicator stops blinking. Check and replace the filter. ✽ ✽✽ red The lamp cannot light up. (The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 79
    POWER green / red WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP 1/2 REP. yellow Projector Condition ✽ ✽ ✽ Fig.2 Filter replacement icon Fig.3 ✽ If the Filter counter reached a time set in the timer setting, a Filter replacement icon (Fig.2) appears on the screen and
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 80
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers + 3 SXGA+ 4 SXGA+ 5 MAC 21 MAC MAC WXGA 1 WXGA 2 WXGA 3 WXGA 4 WXGA 6 WXGA 7 WXGA 8 WXGA 9 WXGA 10 WXGA 11 WXGA 12 WUXGA 1 WUXGA 2 WSXGA+1 WXGA+1 WXGA+2 UXGA 1 UXGA 2 UXGA 3 UXGA 4 UXGA 5
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 81
    is selected in the Input Menu. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 8 D-WXGA 9 D-WXGA 10 D-WXGA 11 D-WXGA 12 RESOLUTION 640x480 720x480 768x575 800x600 1024x768 1366x768 1360x768 1376x768 1360x768 1366x768 1280x768
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 82
    Appendix List of Picture in Picture RGB RGB - Input1 Scart - HDMI - RGB o MAIN Input2 Video o Component o Video o Input3 S-Video o Network o Input1 Scart HDMI RGB - - o - - o - - o o o - - o - o o - - o o - o o o - o SUB Input2 Video Component
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 83
    Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Panel Resolution LCD Panel System Panel Resolution Number of Pixels Signal Compatibility Color System SD/HDTV Signal Scanning Frequency Optical Information Projection Lens Projection Lamp
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 84
    Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable USB Cable Lens Mount Cover PIN Code Label Lens Antitheft Screw * * Contact the dealer where you purchased the projector or the service center about the Lens Antitheft Screw. ● The
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 85
    Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input Input 1 RGB (PC analog) RGB (Scart) RGB (HDMI) Input 2 RGB Video
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 86
    Appendix Configurations of Terminals INPUT 1/ANALOG OUT Terminal: Analog RGB (Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 Input 1 Red Input 2 Green Input 3 Blue Input 4 No Connect 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) Output 1 Red Output 2 Green Output
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 87
    Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 88
    Appendix Dimensions Unit: inch (mm) 15.59 (396.0) 17.76 (451.0) 21.66 (550.1) 3.5˃MAX 3.44 (87.3) 3.70 (94.0) (PANEL CENTER) 3.94 (100.0) 3.94 (100.0) 6.89 (175.0) 3.15 (80.0) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) 10.85 (275.5) 88 5.55 (141.0) 5.55 (141.0)
  • Sanyo PLC-WTC500AL | Owner's Manual - Page 89
    KV5AM SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
*Projection lens is optional.
Multimedia Projector
MODEL
PLC-WTC500AL
Owner’s Manual