Sanyo PLC-WTC500L Owner's Manual
Sanyo PLC-WTC500L - 5000 Lumens Manual
 |
View all Sanyo PLC-WTC500L manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-WTC500L manual content summary:
- Sanyo PLC-WTC500L | Owner's Manual - Page 1
Multimedia Projector MODEL PLC-WTC500L *Projection lens is optional. Owner's Manual - Sanyo PLC-WTC500L | Owner's Manual - Page 2
Features and Design ◆ Functionally Rich This projector has many useful functions such as lens shifting, ceiling and rear projection, perpendicular omnidirectional projection, variety of lens options, etc. ◆ Multilanguage Menu Display Operation menu is available in 12 languages; English, German, - Sanyo PLC-WTC500L | Owner's Manual - Page 3
Instructions 63 Replacing the Filter Cartridge 64 Resetting the Filter Counter 65 Resetting the Scroll Counter 65 Auto Lamp Selection System 66 Lamp Replacement 67 Warning Indicators 69 Cleaning the Projection Lens 70 Cleaning the Projector Cabinet 70 Appendix 71 Troubleshooting - Sanyo PLC-WTC500L | Owner's Manual - Page 4
of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT - Sanyo PLC-WTC500L | Owner's Manual - Page 5
instructions marked on the projector. For added protection to the projector projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement projector. NOTE FOR CUSTOMERS IN THE US Hg LAMP - Sanyo PLC-WTC500L | Owner's Manual - Page 6
of the filter, refer to "Filter counter" on page 59 and "Maintenance and Care" on pages 60-61. Damages to the projector caused by using an uncleaned filter or improper maintenance will void the warranty on the projector. Top Control WARNING FILTER indicator Fig.1 Filter replacement icon Fig - Sanyo PLC-WTC500L | Owner's Manual - Page 7
Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in - Sanyo PLC-WTC500L | Owner's Manual - Page 8
Instructions Moving the Projector Use the hand grip when moving the projector. Replace the lens cap and retract the adjustable feet to prevent damage to the lens and cabinet when carrying. When the projector is not in use for an extended period, put it into a suitable case to protect the projector - Sanyo PLC-WTC500L | Owner's Manual - Page 9
instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number(s) : PLC-WTC500L Trade Name : Sanyo Responsible party : SANYO feature to be sure that the plug Should the fuse need to be replaced, an ASTA approved BS 1362 - Sanyo PLC-WTC500L | Owner's Manual - Page 10
!7 !1 Infrared Remote Receiver (Back) !2 Lamp Cover !3 Filter Cover !4 Exhaust Vent CAUTION Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side. ✽Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector. *Kensington - Sanyo PLC-WTC500L | Owner's Manual - Page 11
Side Terminal t y u Part Names and Functions q we r i o q HDMI TERMINAL Connect the HDMI signal (including sound signal) from video equipment or the DVI signal from computer to this terminal (p.20). w COMPUTER INPUT TERMINAL (ANALOG) Connect the computer (or RGB scart) output signal to this - Sanyo PLC-WTC500L | Owner's Manual - Page 12
Part Names and Functions Side Terminal !0 !1 !2 !3 !0 USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with the supplied USB cable (p.20). !1 R/C JACK When using the wired - Sanyo PLC-WTC500L | Owner's Manual - Page 13
a time set in the timer setting, urging immediate filter/ filter cartridge replacement (pp.62-63, 79). !0 LAMP 2 REPLACE indicator Turn yellow when the life of the projection lamp2 draws to an end. (pp.66-67, 78) !1 POWER indicator - Light red while the projector is in stand-by mode. - Light green - Sanyo PLC-WTC500L | Owner's Manual - Page 14
or a pointer for the laser light window or a signal is being sent from wireless mouse operation (pp.32-33). the remote control to the projector (p.32). r Laser Light window A laser beam is emitted from here (p.32). !1 INFO. button Display the input source information (p.30). t ON button - Sanyo PLC-WTC500L | Owner's Manual - Page 15
to initialize the remote control code or switch the Spotlight and Pointer to the Laser pointer function (p.32). @3 SHUTTER button Close the built-in shutter for light blocking.(pp.28,58) @4 KEYSTONE button Correct keystone distortion (p.31). @5 LENS SHIFT button Select the Lens Shift function (p.28 - Sanyo PLC-WTC500L | Owner's Manual - Page 16
● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared 16.4' (5 m) Remote Receivers) when pressing the buttons. Maximum - Sanyo PLC-WTC500L | Owner's Manual - Page 17
or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 55. 1 Press and hold the MENU and a number button (1-8) for more than five - Sanyo PLC-WTC500L | Owner's Manual - Page 18
to the proper height; to raise the projector, rotate the both feet clockwise. To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise. To correct keystone distortion, press the KEYSTONE button on the remote control or select Keystone from the menu (see - Sanyo PLC-WTC500L | Owner's Manual - Page 19
Lens Installation When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the sales dealer for detailed information of the optional lens specifications. Removing the lens 1 Shift the lens to the center position by using the Lens shift - Sanyo PLC-WTC500L | Owner's Manual - Page 20
PORT ✔Notes: • USB cable connection is needed when operating the computer with the remote control. • When the Standby mode is set to "Eco" in the Setting, up Sound of "HDMI setup" to "AUDIO1". (p.58) • This projector can be connected to the corresponding equipment of DVI however depending on the - Sanyo PLC-WTC500L | Owner's Manual - Page 21
used for connection • Video Cable (RCA x 1) • VGA-Scart Cable • S-VIDEO Cable • BNC Cable • HDMI Cable (Cables are not supplied with the projector.) S-video Output Composite Video Output Digital Output RGB Scart 21-pin Output Refer to the Monitor Out Signal Table (next page). Composite - Sanyo PLC-WTC500L | Owner's Manual - Page 22
(Mini Plug [stereo] x 2) • Audio Cable (RCA x 2) (Cables are not supplied with the projector.) Audio Output Audio cable (RCA) Audio cable (stereo) AUDIO IN MONITOR OUT and AUDIO OUT Specifications Selected Input Input 1 Input 2 Input 3 Network MONITOR OUT Terminal Input 1(D-Sub) Input 2(5-BNC - Sanyo PLC-WTC500L | Owner's Manual - Page 23
, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet does not match your AC outlet, contact your sales dealer. Projector side For the U.S.A. and Canada Ground AC outlet side For Continental - Sanyo PLC-WTC500L | Owner's Manual - Page 24
after 20 seconds. Selected Input Source and Lamp Control Lamp control Lamp status See pages 54,66 for the Lamp control and status. ✔Note: • The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. PIN Code Input Dialog Box After the - Sanyo PLC-WTC500L | Owner's Manual - Page 25
button on the remote control again to turn off the projector. The POWER indicator starts to blink red after 3 seconds. After the projector is turned off, off?" disappears after 4 seconds. TO MAINTAIN LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF. - Sanyo PLC-WTC500L | Owner's Manual - Page 26
Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu. 2 Use - Sanyo PLC-WTC500L | Owner's Manual - Page 27
*The menu bar displays changes depending on the input signals. Guide Window Show the selected Menu of the OnScreen Menu. System Select projector's operating configurations (pp.49-62). - Language - Logo - Picture in Picture - Background - Lamp mode - Lamp control - Filter control - Pointer - Remote - Sanyo PLC-WTC500L | Owner's Manual - Page 28
Operation Operating with Projector Control Lens Operation The following lens operation can be made with the Lens button on the top control. Press the Lens button to enter each lens operation mode. The selected adjustment display appears on the screen. Zoom ➜ Focus ➜ Lens Shift Zoom Adjustment - Sanyo PLC-WTC500L | Owner's Manual - Page 29
is turned off, "On" is displayed. Press the Point 7 8 buttons again to turn the sound back on. Basic Operation Top Control VOLUME +/- buttons Remote Control VOL - button VOL + button MUTE button Volume Dialog Box Approximate level of the volume. Press the MUTE button to set the Mute function - Sanyo PLC-WTC500L | Owner's Manual - Page 30
display can be used to confirm the current operating condition of the projector and the signal being projected through the projector. Remote Control AUTO PC button D.ZOOM button ZOOM button FREEZE button INFO. button POINT ed buttons SCREEN button LENS SHIFT button Press the INFO. button on the - Sanyo PLC-WTC500L | Owner's Manual - Page 31
button PIP VOL. button KEYSTONE button SHUTTER button SHUTTER button See pages 28 and 58 for details. P-TIMER button Press the P-TIMER button on the remote control. The P-Timer display "00:00" appears on the screen and the countdown starts (00:00-59:59). To stop the countdown, press the P-TIMER - Sanyo PLC-WTC500L | Owner's Manual - Page 32
to activate the Pointer function. (The Laser pointer has switched to the Pointer function.) 2 Press the LASER button on the remote control pointing toward the projector. The Spotlight or Pointer is displayed on the screen with the LASER button lighting green. Then move the Spotlight or Pointer - Sanyo PLC-WTC500L | Owner's Manual - Page 33
Wireless Mouse Operation The remote control can be used as a wireless mouse for your computer. 1 Before operating the wireless mouse, connect your computer and the projector with the supplied USB cable (p. 20). When the Pointer function is used, the wireless mouse is not available. 2 When a USB - Sanyo PLC-WTC500L | Owner's Manual - Page 34
control. The input source appears on the screen as you press each button. Select the connected input source. Top Control INPUT button Remote Control button operation INPUT 1 button Input 1 RGB (PC analog) RGB (Scart) HDMI INPUT 2 button Input 2 RGB Video Component Top Control Operation Press - Sanyo PLC-WTC500L | Owner's Manual - Page 35
is connected. Video When the video signal is connected. Component* When the component signal is connected. * If the projector cannot reproduce proper video image, select a system manually (see "Video System Selection" on page 36) *"Component" can accept the component signal and the analog RGB - Sanyo PLC-WTC500L | Owner's Manual - Page 36
itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. Component - Sanyo PLC-WTC500L | Owner's Manual - Page 37
WXGA, UXGA or WUXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector the connection between your computer and the projector. (See "Troubleshooting" on page 68.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The - Sanyo PLC-WTC500L | Owner's Manual - Page 38
pressing the AUTO PC button on the remote control. Remote Control AUTO PC button Menu Operation Auto the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can is not provided properly with this operation, manual adjustments are required (pp.39-40). • - Sanyo PLC-WTC500L | Owner's Manual - Page 39
enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Use the - Sanyo PLC-WTC500L | Owner's Manual - Page 40
Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box - Sanyo PLC-WTC500L | Owner's Manual - Page 41
desired image level and then press the SELECT button. Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for graphics. (This icon is displayed with the computer signal.) Image Menu Image Menu icon Move the - Sanyo PLC-WTC500L | Owner's Manual - Page 42
Image Adjustment Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display - Sanyo PLC-WTC500L | Owner's Manual - Page 43
of the following options. Off Disabled. L1 For an active picture. L2 For a still picture. Film For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Image Adjustment ✔Notes: • Progressive cannot be selected when 480p, 575p, or 720p is - Sanyo PLC-WTC500L | Owner's Manual - Page 44
Image Adjustment Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Store To store the adjusted data, select Store and press the SELECT button. Use the Point ed buttons - Sanyo PLC-WTC500L | Owner's Manual - Page 45
function is set to "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to "On," the picture is left/right reversed. This function is used to project the image from the rear - Sanyo PLC-WTC500L | Owner's Manual - Page 46
original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to and press the SELECT button. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the " - Sanyo PLC-WTC500L | Owner's Manual - Page 47
an input source from the Input Menu (p.35) again, or adjust the screen size with the D.ZOOM buttons on the remote control. Screen Adjustment ✔Notes: • The projector cannot display any resolution higher than 1600 x 1200. If your computer's screen resolution is higher than that, lower the resolution - Sanyo PLC-WTC500L | Owner's Manual - Page 48
center areas. Wide Provide the image at the 16:9 wide screen ratio. Full Provide the full screen image. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the screen for a few seconds and then the Aspect - Sanyo PLC-WTC500L | Owner's Manual - Page 49
Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu. - Sanyo PLC-WTC500L | Owner's Manual - Page 50
Then the captured image will be displayed the next time you turn on the projector. To cancel the Capture function, select [No]. Capture Select [Yes] to image (p.41). • A signal from a computer can be captured up to WXGA (1280 x 800). A signal from video equipment can be captured except for 720p - Sanyo PLC-WTC500L | Owner's Manual - Page 51
the pointer to "Set." Press the SELECT button so that you can change the Logo PIN code lock setting. When using remote control Press the Number buttons on the remote control to enter a number (p.15). When you complete entering a four-digit number, the pointer moves to "Set." Press the SELECT button - Sanyo PLC-WTC500L | Owner's Manual - Page 52
when Main picture is selected. Button operation at the PIP mode on the remote control and top control : In Picture in Picture mode, press the SELECT button sub picture and Point ed7 8buttons operate as follows. e : Replace the Main picture and Sub picture. d : Change the Subpicture - Sanyo PLC-WTC500L | Owner's Manual - Page 53
recommended total hours of use in the Lamp 1/2 mode, the Lamp mode will be switched to Lamp 1 or Lamp 2 mode automatically. Switching operation is done when the lamp is changed. • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the - Sanyo PLC-WTC500L | Owner's Manual - Page 54
mode for the used environment. ✔Note: • A lamp is switched to the lamp which is not exceeding the recommended total hours of use next time when you turn on the projector, even when the Mode 1 is selected. Filter control You can replace the filter with this function. Press the SELECT button at - Sanyo PLC-WTC500L | Owner's Manual - Page 55
) or a pattern of the Pointer (Arrow, Finger, or Dot). (See page 32 for operation.) Pointer Setting Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same - Sanyo PLC-WTC500L | Owner's Manual - Page 56
Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option " is selected, all of the infrared remote receivers are activated regardless of the RC sensor setting. The projector may be effected the noise of the fluorescent - Sanyo PLC-WTC500L | Owner's Manual - Page 57
or any button on the top control or remote control is pressed. Shut down When the lamp has been fully cooled down, the power will projector and decreases the lamp life. Slant setting +70° Select the projector's installation condition from the following options: UP Off When using the projector - Sanyo PLC-WTC500L | Owner's Manual - Page 58
both of the remote control and the top control. Management The Shutter Management function turns off the projection lamp when the projector is left equipment vary from equipment to equipment. For details, refer to the owner's manual of video equipment. When the black part of the image are destroyed - Sanyo PLC-WTC500L | Owner's Manual - Page 59
. buttons. If the top control accidentally becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Key lock Select Key lock. Use the Point ed buttons to choose one - Sanyo PLC-WTC500L | Owner's Manual - Page 60
Use the Point ed buttons on the top control or Number buttons on the remote control to enter a number. When using top control Use the Point ed buttons Press the SELECT button to close the dialog box. PIN code lock When the projector is locked with a PIN code, the PIN code lock symbol appears on the - Sanyo PLC-WTC500L | Owner's Manual - Page 61
can no longer be started. Test pattern Various test pattern are available for use when setting up the projector. Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest - Sanyo PLC-WTC500L | Owner's Manual - Page 62
and the Scrolls remaining option. Used Time Show the total accumulated time of the filter use, timer setting option and the Reset options. When the projector reaches a time set in the timer setting, the Filter replacement icon (Fig. 1) appears on the screen and the total accumulated time turns red - Sanyo PLC-WTC500L | Owner's Manual - Page 63
work properly. It may cause a breakdown. • Make sure that the projection lamps are turned off when you are replacing the filter cartridge. If you replace the filter cartridge when the projection lamps are turned on, the projector will be shut down automatically for safety purposes. • Do not forget - Sanyo PLC-WTC500L | Owner's Manual - Page 64
authorized dealer or service station for proper cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Replacement filter cartridge can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector PLC-WTC500L ● Replacement Filter Cartridge Type - Sanyo PLC-WTC500L | Owner's Manual - Page 65
. Select [Yes] to continue. 4 Another confirmation dialog box appears, select [Yes] to reset the Filter counter. Resetting the Scroll Counter Be sure to reset the Scroll counter after replacing the filter cartridge. 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons - Sanyo PLC-WTC500L | Owner's Manual - Page 66
reaches the recommended total hours of use. Check the number of lamp on the Lamp Status Display or the LAMP 1/2 REPLACE indicators and replace the lamp. Lamp Status Display The Lamp Status Display appears on screen when the projector is turned on or the input position (input 1, input 2, or Input - Sanyo PLC-WTC500L | Owner's Manual - Page 67
to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot. CAUTION For continued safety, replace with a lamp of the same type lamp. Do not drop the lamp or touch the glass bulb! The glass can shatter and may cause injury. CAUTION When - Sanyo PLC-WTC500L | Owner's Manual - Page 68
give the following information to the dealer. ● Model No. of your projector : PLC-WTC500L ● Replacement Lamp Type No. : POA-LMP125 (Service Parts No. 610 342 2626) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may - Sanyo PLC-WTC500L | Owner's Manual - Page 69
of the projector away from the duct or vent. - Is the filter clean? Clean the filter periodically or replace it with a new one. The projector is shut red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL - Sanyo PLC-WTC500L | Owner's Manual - Page 70
lens. When the projector is not in use, replace the lens cap. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning. Gently wipe the projector cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the - Sanyo PLC-WTC500L | Owner's Manual - Page 71
replacement icon or the Filter warning icon. Lamp control or lamp status icon See pages 62,67. appears. No image - Check the connection between your computer or video equipment and the projector connecting to the projector See your computer's instruction manual for the - Sanyo PLC-WTC500L | Owner's Manual - Page 72
LAMP 1/2 REPLACE indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See pages 66-68, 78. - Check the Lamp 40, 45-48. The edge of image is distorted. - With maximum lens shift, image distortion may be observed. No sound - Check the audio cable - Sanyo PLC-WTC500L | Owner's Manual - Page 73
lock. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the - Sanyo PLC-WTC500L | Owner's Manual - Page 74
Appendix Menu Tree Input Input 1 Input 2 Input 3 RGB (PC analog) RGB (Scart) HDMI Quit RGB Video Component Quit Video S-video Quit Go to System (1) Go to System (1) Go to System (1) Go to System (3) Go to System (2) Go to System (3) Go to System (3) System (1) Mode 1 Mode 2 XGA 1 - - - - - Sanyo PLC-WTC500L | Owner's Manual - Page 75
On/Off Rear On/Off Information Input H-sync freq. V-sync freq. Screen Language Lamp mode Lamp control Lamp 1 Lamp 2 Filter counter Power management Shutter management Remote control Projector ( ) Min Security Remote control SERIAL NO. Key lock PIN code lock Sound Volume Mute Quit 0-63 On - Sanyo PLC-WTC500L | Owner's Manual - Page 76
180 Min. Quit HDMI setup Image Normal/Enhanced Sound HDMI/AUDIO1 Quit Security Test pattern Warning log Filter counter Factory default Quit Key lock Off Projector (all) Projector (part) Remote control (all) Remote control (part) Quit PIN code lock Off/On 1/On 2 PIN code change Quit Quit 8 test - Sanyo PLC-WTC500L | Owner's Manual - Page 77
mode. The projection lamp is being cooled down in the Shutter ✽ management mode. The projector is in the Shutter management mode. Press ✽ the ON/STAND-BY button to turn on the projector. ✽ ✽ ✽ ✽ Fig.1 Filter replacement icon and "Please wait..." The filter is scrolled using the - Sanyo PLC-WTC500L | Owner's Manual - Page 78
returns to normal. When turning on the projector, the WARNING TEMP. indicator stops blinking. Check and replace the filter. ✽ ✽✽ red The lamp cannot light up. (The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is - Sanyo PLC-WTC500L | Owner's Manual - Page 79
POWER green / red WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP 1/2 REP. yellow Projector Condition ✽ ✽ ✽ Fig.2 Filter replacement icon Fig.3 ✽ If the Filter counter reached a time set in the timer setting, a Filter replacement icon (Fig.2) appears on the screen and the - Sanyo PLC-WTC500L | Owner's Manual - Page 80
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers SXGA+ 3 SXGA+ 4 SXGA+ 5 MAC 21 MAC MAC WXGA 1 WXGA 2 WXGA 3 WXGA 4 WXGA 6 WXGA 7 WXGA 8 WXGA 9 WXGA 10 WXGA 11 WUXGA 1 WUXGA 2 WSXGA+1 WXGA+1 WXGA+2 UXGA 1 UXGA 2 UXGA 3 UXGA 4 UXGA 5 720p - Sanyo PLC-WTC500L | Owner's Manual - Page 81
59.954 59.887 60.000 60.000 (Interlace) 60.000 (Interlace) 50.000 (Interlace) 60.000 50.000 ✔Notes: • When the input signal is D-WXGA +1 images may not be displayed properly depending on computers • Specifications are subject to change without notice.. 81 - Sanyo PLC-WTC500L | Owner's Manual - Page 82
Appendix List of Picture in Picture RGB RGB - Input1 Scart - HDMI - RGB o MAIN Input2 Video o Component o Video o Input3 S-Video o Network o Input1 Scart HDMI RGB - - o - - o - - o o o - - o - o o - - o o - o o o - o SUB Input2 Video Component - Sanyo PLC-WTC500L | Owner's Manual - Page 83
Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Panel Resolution LCD Panel System Panel Resolution Number of Pixels Signal Compatibility Color System High Definition TV Signal Scanning Frequency Optical Information Projection Lens Projection Lamp Remote - Sanyo PLC-WTC500L | Owner's Manual - Page 84
Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable USB Cable Lens Mount Cover PIN Code Label Lens Antitheft Screw * * Contact the dealer where you purchased the projector or the service center about the Lens Antitheft Screw. ● The specifications are - Sanyo PLC-WTC500L | Owner's Manual - Page 85
Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input Input 1 RGB (PC analog) RGB (Scart) RGB (HDMI) Input 2 RGB Video - Sanyo PLC-WTC500L | Owner's Manual - Page 86
Appendix Configurations of Terminals INPUT 1/ANALOG OUT Terminal: Analog RGB (Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 Input 1 Red Input 2 Green Input 3 Blue Input 4 No Connect 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) Output 1 Red Output 2 Green Output - Sanyo PLC-WTC500L | Owner's Manual - Page 87
Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set - Sanyo PLC-WTC500L | Owner's Manual - Page 88
Appendix Dimensions Unit: inch (mm) 15.59 (396.0) 17.76 (451.0) 21.66 (550.1) 3.5˃MAX 3.44 (87.3) 3.70 (94.0) (PANEL CENTER) 3.94 (100.0) 3.94 (100.0) 6.89 (175.0) 3.15 (80.0) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) 10.85 (275.5) 88 5.55 (141.0) 5.55 (141.0) - Sanyo PLC-WTC500L | Owner's Manual - Page 89
KV5AL SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
 |
 |
*Projection lens is optional.
Multimedia Projector
MODEL
PLC-WTC500L
Owner’s Manual