Sanyo PLC-WXU300 Owner's Manual

Sanyo PLC-WXU300 - 2500 Lumens Manual

Get Sanyo PLC-WXU300 - 2500 Lumens PDF manuals and user guides
UPC - 086483074226
View all Sanyo PLC-WXU300 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-WXU300 manual content summary:

  • Sanyo PLC-WXU300 | Owner's Manual - Page 1
    Multimedia Projector MODEL PLC-WXU300 PLC-WXU300K Network Supported □ Wired LAN 100-Base-TX/10-Base-T Refer to the Owner's Manuals below for details about network function. □ Network Set-up and Operation □ PJ Network Manager Owner's Manual
  • Sanyo PLC-WXU300 | Owner's Manual - Page 2
    projector - Blackboards* can be used as a projection screen. *The board color is limited to Green (pp.33, 40). via network. For details, refer to the owner's manual "Network Set-up and Operation." ♦ Lamp Control Brightness of the projection lamp the screen ♦ Power Management logo (pp.47
  • Sanyo PLC-WXU300 | Owner's Manual - Page 3
    60 Maintenance and Cleaning 61 WARNING indicator 61 Cleaning the Filters 62 Resetting the Filter Counter 62 Attaching the Lens Cap 63 Cleaning the Projection Lens 63 Cleaning the Projector Cabinet 63 Lamp Replacement 64 Appendix 66 Troubleshooting 66 Menu Tree 70 Indicators
  • Sanyo PLC-WXU300 | Owner's Manual - Page 4
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC
  • Sanyo PLC-WXU300 | Owner's Manual - Page 5
    power supplied, consult your authorized dealer or local power company. Follow all warnings and instructions marked on the projector. For added protection to the projector with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved
  • Sanyo PLC-WXU300 | Owner's Manual - Page 6
    heat. Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20° Do not tilt the projector more than 20 the projector by courier or any other transport service with this case, otherwise the projector can be damaged. When handling the projector, do
  • Sanyo PLC-WXU300 | Owner's Manual - Page 7
    PLC-WXU300 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone No 818)998-7322 AC Power Cord Requirement The AC Power Cord supplied with this projector your User Instructions. If the plug supplied is
  • Sanyo PLC-WXU300 | Owner's Manual - Page 8
    and Functions Front ⑤⑨ Back ⑦⑧ ⑨ ⑩⑪ ⑫ ⑬ ⑥ Bottom ⑭ ① Infrared Remote Receiver ② Zoom Ring ③ Focus Ring ④ Projection Lens ⑤ Lens Cap (See page 63 for attaching.) CAUTION Do not turn on a projector with lens cap attached. High temperature from light beam may damage lens cap and result in
  • Sanyo PLC-WXU300 | Owner's Manual - Page 9
    ① ② ③ ④ ⑤ ⑩ ⑨ ⑧ ⑦⑥ ① CONTROL PORT When the projector is controlled by a computer, connect to this jack with serial control cable. 14, 16). ⑤ LAN Connection Terminal Connect the LAN cable (refer to the owner's manual of "Network Set-up and Operation"). ⑥ S-VIDEO IN Connect the S-VIDEO output
  • Sanyo PLC-WXU300 | Owner's Manual - Page 10
    setting menu (pp.23, 45). ⑧ WARNING indicator -Lights red when the projector detects an abnormal condition. -Blinks red when the internal temperature of the projector exceeds the operating range (pp.61, 72). ⑨ LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp
  • Sanyo PLC-WXU300 | Owner's Manual - Page 11
    Remote Control Part Names and Functions ① ON/STAND-BY button Turn the projector on or off. (pp.18-20) ② function. (pp.25,51) ⑯ P-TIMER button Operate the P-timer function. (p.26) ⑰ LAMP button Select a lamp mode. (pp.25, 55) ⑱ INFO. button Operate the information function. (p.60) ⑲
  • Sanyo PLC-WXU300 | Owner's Manual - Page 12
    is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the
  • Sanyo PLC-WXU300 | Owner's Manual - Page 13
    latches on both side of the projector. Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to a proper height, and tilt. Keystone distortion can be adjusted automatically with the Auto setup function or manually by using the remote control or the menu operation
  • Sanyo PLC-WXU300 | Owner's Manual - Page 14
    • HDMI-DVI cable (*One cable is supplied; other cables are not supplied with the projector.) Audio Output Monitor Output Monitor Output /Monitor COMPONENT IN and not the COMPUTER IN 2. Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables
  • Sanyo PLC-WXU300 | Owner's Manual - Page 15
    3) • S-Video cable • Audio cable (Cables are not supplied with the projector. ) External Audio Equipment Video and Audio Output (Video) (L) OUT is plugged-in, the projector's builtin speaker is not available. Unplug the power cords of both the projector and external equipment from the AC
  • Sanyo PLC-WXU300 | Owner's Manual - Page 16
    • Component cable • Component-VGA Cable (Cables are not supplied with this projector.) RGB Scart 21- Component Video Output pin Output (Y, Pb the projector's built-in speaker is not available. • See page 77 for ordering optional cables. 16 Unplug the power cords of both the projector and
  • Sanyo PLC-WXU300 | Owner's Manual - Page 17
    , it is in Stand-by mode and consumes a little electric power. Installation Connect the AC power cord (supplied) to the projector. NOTE ON THE POWER CORD AC power cord must meet requirement of the country where you use the projector. Confirm the AC plug type with the chart below and proper
  • Sanyo PLC-WXU300 | Owner's Manual - Page 18
    , etc.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap (see pages 8, 63). 3 Press the ON/STAND-BY button on the top control or on the remote control. The POWER indicator lights green and the cooling fans
  • Sanyo PLC-WXU300 | Owner's Manual - Page 19
    number in a column on page 80 of this manual and keep it on hand. Should the PIN code be missing or forgotten, consult your dealer or service center. Basic Operation PIN Code Input Dialog Box After the OK icon disappears, you can operate the projector. Note: • If the PIN code number is not
  • Sanyo PLC-WXU300 | Owner's Manual - Page 20
    changed according to the temperature inside the projector. • Do not put the projector in a case before the projector is cooled enough. • If the WARNING indicator blinks or lights red, see "WARNING indicator" on page 61. • While the POWER indicator is blinking, the lamp is being cooled down and the
  • Sanyo PLC-WXU300 | Owner's Manual - Page 21
    Menu The projector can be adjusted or set via the On-Screen Menu. The menus have a hierarchical structure, with a main menu that is divided into submenus, which are further divided into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. 1 Press
  • Sanyo PLC-WXU300 | Owner's Manual - Page 22
     Setting Used to set the projector's operating configurations (pp.44-59).  Information Display the input source information: Input, H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter, Power management, Keylock, PIN code lock and Remote control (p.60).  Network See owner
  • Sanyo PLC-WXU300 | Owner's Manual - Page 23
    the AUTO SETUP button on the top control or the AUTO SET button on the remote control. Refer to page 45 for the setting of the Auto setup function.  only; it does not correct horizontal distortion. • Auto Keystone cannot work when Ceiling feature is set to On in the Setting menu (p.50). • Perfect
  • Sanyo PLC-WXU300 | Owner's Manual - Page 24
    seconds. Top Control VOLUME+/buttons Mute Press the MUTE button on the remote control to select On to temporarily turn off the sound. To +/- buttons. The Mute function is also effective for the AUDIO OUT jack. Remote Control Menu Operation 1 Press the MENU button to display the On-Screen Menu.
  • Sanyo PLC-WXU300 | Owner's Manual - Page 25
    next page for the description of other buttons. Normal....... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. PIP button Press the PIP button on the remote control to enter P in P or P by P. Mode of Picture in Picture and input source will be
  • Sanyo PLC-WXU300 | Owner's Manual - Page 26
    stop the countdown, press the P-TIMER button. To cancel the P-Timer function, press the P-TIMER button again. IMAGE button Press the IMAGE button on the remote control to select a desired image mode of the screen. See pages 33, 40 for details. SCREEN button Select the screen size (See pages 35-36
  • Sanyo PLC-WXU300 | Owner's Manual - Page 27
    1: RGB ) Direct Operation Choose Computer 1(RGB) by pressing the INPUT button on the top control or press the COMPUTER 1 button on the remote control. Before using INPUT button, correct input source should be selected through Menu operation as described below. Top Control INPUT button Computer
  • Sanyo PLC-WXU300 | Owner's Manual - Page 28
    2: RGB) Direct Operation Choose Computer 2(RGB) by pressing the INPUT button on the top control or press the COMPUTER 2 button on the remote control. Remote Control COMPUTER 2 button Computer 2(RGB) COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT
  • Sanyo PLC-WXU300 | Owner's Manual - Page 29
    WXGA, UXGA or WUXGA with its Multi-scan system and Auto PC adjustment. If a computer is selected as a signal source, this projector Check the connection between your computer and the projector. (See "Troubleshooting" on page 67.) The preset system is manually adjusted in the PC adjust Menu. The
  • Sanyo PLC-WXU300 | Owner's Manual - Page 30
    adjusted parameters from the Auto PC adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp.31-32). • The Auto PC adjustment
  • Sanyo PLC-WXU300 | Owner's Manual - Page 31
    PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen
  • Sanyo PLC-WXU300 | Owner's Manual - Page 32
    Computer Input Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select selected in the PC System Menu (p.29). • When input computer signal to the projector, PC adjust will become available. 32 Press SELECT button to store adjusted data
  • Sanyo PLC-WXU300 | Owner's Manual - Page 33
    by pressing the IMAGE button on the remote control. Remote Control IMAGE button Menu Operation 1 Press Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for four colors. Image 1-4 For viewing with the user preset image mode in the Image adjust Menu (
  • Sanyo PLC-WXU300 | Owner's Manual - Page 34
    obtain a better balance of contrast (from 0 to 15). Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and , Green or Blue is adjusted, Color temp. will change to User. • When Blackboard(Green) or Colorboard is selected in Image select,
  • Sanyo PLC-WXU300 | Owner's Manual - Page 35
    cannot display any resolution higher than 1920 x 1200. If your computer's screen resolution is higher than it, reset the resolution to the lower before connecting to the projector. • The image data in other than 1280 x 800 is modified to fit the screen size in initial mode. • True, Full and
  • Sanyo PLC-WXU300 | Owner's Manual - Page 36
    Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset by pressing the D.ZOOM - button on the remote control. To exit the Digital zoom +/- mode Menu is used (p.32). • The minimum compression ratio is limited depending on the input signal, when
  • Sanyo PLC-WXU300 | Owner's Manual - Page 37
    control. Before using INPUT button, correct input source should be selected through menu operation as described below. Remote Control VIDEO button Video S-VIDEO button S-video Top Control COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT
  • Sanyo PLC-WXU300 | Owner's Manual - Page 38
    using these buttons, correct input source should be selected through Menu operation as described below. Top Control INPUT button Computer 1 Remote Control COMPUTER 1 button Computer 1(RGB) Computer 2  HDMI Video S-video COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR
  • Sanyo PLC-WXU300 | Owner's Manual - Page 39
    system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL
  • Sanyo PLC-WXU300 | Owner's Manual - Page 40
    Image 4 by pressing the IMAGE button on the remote control. Menu Operation 1 Press the MENU button to Standard Normal picture mode preset on the projector. Cinema Picture mode adjusted with fine preset four colors. Image 1-4 For viewing with the user preset image mode in the Image adjust Menu (see
  • Sanyo PLC-WXU300 | Owner's Manual - Page 41
    to deepen blue tone (from 0 to 63). Note: • When the White balance Red, Green, or Blue is adjusted, the Color temp. level will change to User. • Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.39). • When Blackboard(Green) or Colorboard is selected in Image select
  • Sanyo PLC-WXU300 | Owner's Manual - Page 42
    picture. L2........... For a still picture. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Yes. All
  • Sanyo PLC-WXU300 | Owner's Manual - Page 43
    image at the 16:9 wide screen ratio. Only for 4:3 video aspect ratio signals. Natural wide Modify the 4:3 aspect ratio image to fit the screen size(16:9 aspect ratio) by stretching the image to make it look natural. Custom Adjust the screen scale and position manually with this function. Press the
  • Sanyo PLC-WXU300 | Owner's Manual - Page 44
    Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu.
  • Sanyo PLC-WXU300 | Owner's Manual - Page 45
    keystone distortion according to the projector's tilt. Manual . . . . Works only when remote control. Off Disables Auto Keystone. Note: • While Input search is set to On1 or On2, the status of Input and Lamp Auto Keystone function cannot work when the Ceiling feature is set On in the Setting
  • Sanyo PLC-WXU300 | Owner's Manual - Page 46
    power cord is unplugged. Reset....... Release the keystone correction when the AC power blue background Black . . Project a black background User . . Project an image captured in the Logo projector. Use this function when you want to project the image as early as possible even when the lamp
  • Sanyo PLC-WXU300 | Owner's Manual - Page 47
    and Capture functions cannot be selected. Logo select Logo select This function decides on the starting-up display from among following options. User......... Show the image you captured. Default..... Show the factory-set logo. Off Show the countdown display only. Picture in Picture Standby mode
  • Sanyo PLC-WXU300 | Owner's Manual - Page 48
    WXGA (1280 x 800). A signal from video equipment can be captured except for 1035i, and 1080i. • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector interrupted while capturing an image, User is not included in Logo
  • Sanyo PLC-WXU300 | Owner's Manual - Page 49
    -digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, Logo PIN code and the number will turn red for a moment. Enter the correct Logo PIN code
  • Sanyo PLC-WXU300 | Owner's Manual - Page 50
    /right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be vary from equipment to equipment. For details, refer to the owner's manual of your Digital R/G/B equipment. When the black parts of the image are
  • Sanyo PLC-WXU300 | Owner's Manual - Page 51
    screen within the main screen. (Picture in Picture combinations provided in this projector are shown on pages 75.) Only the sound on the main picture is the COMPUTER 1/2, HDMI, VIDEO, S-VIDEO or COMPONENT button on the remote control or through Input Menu operation. Operation of the Sub picture In
  • Sanyo PLC-WXU300 | Owner's Manual - Page 52
    network environment, and receive an e-mail about projector status while the projector is powered off. Eco Select Eco when you do not use the projector via network. The projector's network function will stop when turning off the projector. Refer to the owner's manual of "Network Set-up and Operation
  • Sanyo PLC-WXU300 | Owner's Manual - Page 53
    start When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: • Be sure to turn off the projector properly (see "Turning Off the Projector" on page 20). If the projector is turned off in the incorrect sequence, the
  • Sanyo PLC-WXU300 | Owner's Manual - Page 54
    sound or other information displayed on the screen. If the input signal Closed Caption contains closed captions, you can turn on the feature and Power management Off switch the channels. Press the Point ▲▼ buttons to select On start Off Off, CC1, CC2, CC3 or CC4. If the closed caption
  • Sanyo PLC-WXU300 | Owner's Manual - Page 55
    exceeds the recommended total hours of use, the replacement icon will be displayed at the time of power on. Then the projector will turn off after 3 minutes. Lamp replacement icon • The Lamp replacement icon will not appear when the Display function is set to Off (p.46), during "FREEZE
  • Sanyo PLC-WXU300 | Owner's Manual - Page 56
    you to use the Key lock and PIN code lock function to set the security for the projector operation. Power management Off On start Off Key lock This function locks the top control and remote control buttons to prevent operation by unauthorized persons. Select Key lock and then press the SELECT
  • Sanyo PLC-WXU300 | Owner's Manual - Page 57
    -digit number. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, PIN code and the number will turn red for a moment. Enter the correct PIN code all over again
  • Sanyo PLC-WXU300 | Owner's Manual - Page 58
    . Select this mode when using the projector in higher altitudes than above where the RESET and set the timer. The Filter warning icon will not turn off until the filter counter is reset. For details about resetting the timer, refer to "Resetting the Filter Counter" on page 62. Note: The Lamp
  • Sanyo PLC-WXU300 | Owner's Manual - Page 59
    Note: When the Factory default function is executed, all the warning log records will be deleted. Setting Factory default This function returns all setting values except for the User logo, PIN code lock, Logo PIN code lock, Lamp counter Factory default and Filter counter to the factory default
  • Sanyo PLC-WXU300 | Owner's Manual - Page 60
    The selected lamp mode is displayed. Lamp counter The cumulative lamp operating time is displayed. Power management Off, Ready, Shut down or Timer is displayed. Key lock The selected Key lock icon is displayed. PIN code lock Off or On 1 or On 2 is displayed. Remote control The selected remote code
  • Sanyo PLC-WXU300 | Owner's Manual - Page 61
    on once again to verify operation. If the projector cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE
  • Sanyo PLC-WXU300 | Owner's Manual - Page 62
    or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning. Resetting the Filter Counter Be sure to
  • Sanyo PLC-WXU300 | Owner's Manual - Page 63
    and in its vicinity. The explosion or fire hazard may occur even after the AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal parts may be damaged not only by the flammable air spray but also
  • Sanyo PLC-WXU300 | Owner's Manual - Page 64
    Screw ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-WXU300, PLC-WXU300K : POA-LMP131 (Service Parts No. 610
  • Sanyo PLC-WXU300 | Owner's Manual - Page 65
    a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration
  • Sanyo PLC-WXU300 | Owner's Manual - Page 66
    blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 18. - Check the WARNING indicator. If the WARNING indicator lights red, projector cannot be turned on. See page 61. - Check the projection lamp. See page 64. - Unlock
  • Sanyo PLC-WXU300 | Owner's Manual - Page 67
    projector. See your computer's instruction manual for the setting 35,42. Power management does not work. - Power management function Ceiling function. See page 50. Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to Manual
  • Sanyo PLC-WXU300 | Owner's Manual - Page 68
    Key lock function for the remote control function. See page 56. Indicator blinks or lights. - Check the status of the projector with referring to "Indicators and projector Condition". See page 72. code lock. - Contact the dealer where you purchased the projector or the service center. 68
  • Sanyo PLC-WXU300 | Owner's Manual - Page 69
    WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem
  • Sanyo PLC-WXU300 | Owner's Manual - Page 70
    Colorboard Red/Blue/Yellow/Green Image 1 Image 2 Image 3 Image 4 Contrast Brightness Color temp. Red Green Blue Sharpness Gamma Reset Store 0-63 0-63 XLow Low Mid High User 0-63 0-63 0-63 0-15 0-15 Yes/No Image 1 Image 2 Image 3 Image 4 Normal True Full Custom Scale H&V Position Common
  • Sanyo PLC-WXU300 | Owner's Manual - Page 71
    control Mode 1/ Mode 2 Code 1-Code2 Security Fan Fan control Key lock Off Projector Remote control PIN code lock Off/On1/On2 PIN code change L1/L2 Offl/On1/On2 Lamp counter Lamp counter Lamp counter reset Filter counter WARNING log Filter counter H Timer Off/100H/200H/300H Filter counter
  • Sanyo PLC-WXU300 | Owner's Manual - Page 72
    Appendix Indicators and Projector Condition Check the indicators for projector condition Indicators POWER red/green WARNING red LAMP REPLACE yellow Projector Condition The projector is off. (The AC power cord is unplugged.)  The projector is in stand-by mode. Press the ON/STAND-BY
  • Sanyo PLC-WXU300 | Owner's Manual - Page 73
    Compatible Computer Specifications Basically this projector can accept the signal from SXGA 19 SXGA 20 SXGA+ 1 SXGA+ 2 SXGA+ 3 MAC21 MAC MAC WXGA 1 WXGA 2 WXGA 3 WXGA 4 WXGA 6 WXGA 7 WXGA 8 WXGA 9 WXGA 10 WXGA 11 WSXGA +1 WXGA +1 WXGA +2 UXGA 1 UXGA 2 UXGA 3 UXGA 4 WUXGA 1 WUXGA 2 RESOLUTION 1152
  • Sanyo PLC-WXU300 | Owner's Manual - Page 74
    chart below. ON-SCREEN DISPLAY D-480p D-480p D-480p D-575p D-575p D-720p D-720p D-720p D-VGA D-VGA D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 8 D-WXGA 9 D-WXGA 10 D-WXGA 11 RESOLUTION 640 x 480 720 x 480 720 x 480 720 x 575 768 x 575 1280 x 720 1280 x 720
  • Sanyo PLC-WXU300 | Owner's Manual - Page 75
    • Inputting PC digital signals: More than 100MHz • Inputting AV digital signals: 1080p • Inputting signal formats: SXGA20, WUXGA 1, WUXGA 2, WSXGA+ 1, WXGA+2, UXGA 1, UXGA 2, UXGA 3, UXGA4, D-1080p 75
  • Sanyo PLC-WXU300 | Owner's Manual - Page 76
    Projector 12.80" x 3.27" x 9.12" (326mm x 83.1mm x 231.6mm) (Not including protrusions) 6.18 lbs (2.8 kg) 0˚ to 12˚ Panel Resolution LCD . 50-100 Hz Optical Information Projection Image Size (Diagonal) Throw Distance Projection Lens Projection Lamp Adjustable from 30" to 300" 2.4' ~ 25.2' (0.74
  • Sanyo PLC-WXU300 | Owner's Manual - Page 77
    Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide & Safety Manual Soft Carrying Case AC Power Cord Remote Control and Batteries VGA Cable Lens Cap with String PIN Code Label Network Application (CD-ROM) ● The specifications are subject to change without notice. ● LCD panels are
  • Sanyo PLC-WXU300 | Owner's Manual - Page 78
    and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see the owner's manual of "Network Set-up and Operation." Projector Input Computer 2 (Analog) HDMI(Digital
  • Sanyo PLC-WXU300 | Owner's Manual - Page 79
    Cr) Input/Output 2 Green (G/Y) Input/Output 3 Blue (B/Cb) Input/Output 4 ----- 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) 9 +5V Power/----10 Ground (Vert.sync.) 11 Ground/----12 DDC Data/----13 Horiz. sync. Input/Output (Composite H/V sync.) 14 Vert. sync. 15 DDC
  • Sanyo PLC-WXU300 | Owner's Manual - Page 80
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo PLC-WXU300 | Owner's Manual - Page 81
    Dimensions 93.5(3.68) 232.5(9.15) 109.7(4.32) 143.3(5.64) 121.9(4.80) Appendix Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.472) 219.4(8.64) 101(3.98) 55(2.17) < 107.6(4.24) 25(0.98) 23(0.91) < 51.9 (2.05) <
  • Sanyo PLC-WXU300 | Owner's Manual - Page 82
    KE5AC SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Multimedia Projector
MODEL
PLC-WXU300
PLC-WXU300K
Owner’s Manual
Network Supported
□
Wired LAN
100-Base-TX/10-Base-T
Refer to the Owner's Manuals below for
details about network function.
□
Network Set-up and Operation
□
PJ Network Manager