Sanyo PLC-WXU300 Owner's Manual Network for Windows
Sanyo PLC-WXU300 - 2500 Lumens Manual
 |
UPC - 086483074226
View all Sanyo PLC-WXU300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-WXU300 manual content summary:
- Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 1
This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 2
by turning the equipment off and on, the user is encouraged to try to correct the interference by instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-WXU300 Trade Name : Sanyo Responsible party : SANYO - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 4
instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector mail 27 SNMP setting...29 Chapter 4 Controlling the Projector 31 Power control and status check...32 Control...34 Input...34 System - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 5
Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 6
sends mes- sages to the registered e-mail PC1 PC2 addresses when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You can take efficient action for quick recovery. PJ2 PJ1 PC5 Turn ON PJ2 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 7
Vista Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 Safari 3.0 or later * Used to control and set up the projector. The layout of pages in the browser may slightly differ from each - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 8
from the actual operation depending on your computer environment. Use of this manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 9
Follow each chapter to operate the projector. ■ Operate and manage the projector ➔ "4. Controlling the projector" (pp.31-42) ➔ "Power Control and status check" (p. 's manual of PJ Network Manager. Notice about installing Software CD-ROM It is available for controlling and setting of the projector by - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 10
Chapter 1 Preparation 10 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 11
Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 12
the LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal ACT Lamp (Orange) Blink orange when the projector is sending or receiving the data. LAN Cable LINK Lamp (Green) Light green when the projector is connected to the network correctly. Network configuration Set - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 13
DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 14
you do not want to set the Network PIN code, set "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See "3. Basic setting and operation" ➔ "Initial setting" ➔ "Network PIN code setting - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 15
Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 16
Chapter 2 Setup Procedures Wired LAN factory default settings Parameter IP CONFIGURATION LAN 1 MANUAL SELECTED LAN LAN 2 DHCP LAN 3 MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 17
Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 18
login Network PIN code onto the Password text area and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 20
3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 21
Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 22
. Item Description Language Switches display language on the setting page. English or Japanese. Model name........Indicates the model name of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink password authentication on or - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 23
System Industries Association (JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 24
mode IP configuration....Sets DHCP or Manual IP address Sets IP address of the projector Subnet mask.......Sets Subnet mask. Normally the DNS server, access with the assigned IP address to the projector. * All the network setting will reset to the default when setting [0.0.0.0] of the IP Address. - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 25
an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP server*1 Sets server name or IP - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 26
is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99,999 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 27
✐ The projector lamp was turned off, because the projector power circuit failed. Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 28
following message. *The projector lamp has reached replacement time. Lamp ON 2000 h ✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every poweron of the projector. This alert mail - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 29
Setting on the main menu and set up each item. PJ information Item Description Contact Enter user name of the projector etc. (optional) Place Enter place of the projector (optional) Community name(refer).......Enter community name (read only). Default name is "public". Trap Item Description - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 30
is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99,999 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 31
Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 32
. Popup confirmation window Item Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 33
temp. and sets into standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 34
differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 35
function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed. Available selection at the Video/S-video/Scart input - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 36
Chapter 4 Controlling the Projector Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speaker. (0 ~ 63) Mute Suppresses the sound. (ON, OFF) 36 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 37
temp Sets a color temperature mode. (High, Mid, Low, XLow, user) White Balance Red, Green, Blue...... Adjusts each white balance respectively Progressive S witches progressive mode (OFF, L1, L2, Film) Reset Resets the Image adjustment to previous levels. Store Stores the Image adjustment - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 38
projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, screen. Vertical Adjusts the vertical position of the screen. Reset Resets the PC adjustments to the previous levels. Mode Store - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 39
the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item Description Screen Switches the screen mode. (Normal, True, Full, Wide, Zoom - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 40
projector Manual, OFF) Background.........Sets the screen background when no signal input. (Blue, User User) Setting 2 Item Description Ceiling power-on mode when the AC cord is connected to the outlet. Lamp control......Selects lamp control mode. (Normal, Eco) Lamp life control Selects lamp - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 41
display appears, and then click "OK", the time will be reset. Filter warning.....Sets the time to indicate the filter warning message on the screen. (OFF, 100H, 200H, 300H) Factory default..........Sets all of the projector control items to the factory default setting except the following items - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 42
. Security Displays the security (PIN code lock) status (Yes, No) PJ time(h) Displays the accumulated use time of the projector. Lamp Corres. Value(h) Displays the use time (Corresponding value) of the lamp. Filter time(h) Displays the accumulated use time of the filter. Indication of the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 43
Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 43 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 44
the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168 - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 45
. Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 46
*1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 47
(Network PIN code*2) for the projector and then press "Enter" key on Power on C02 Power off C09 Volume up C0A Volume down C0B Audio Mute on C0C Audio Mute off C1C Menu display on C1D menu display off *1 F urther instructions about the telnet application, please see the on-line guide - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 48
not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." will be displayed on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 49
Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 50
proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 51
to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 52
address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 53
of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong access the projector installed on the company's local area network from a remote location? A There are some ways to access to the projector in the - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 54
Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 55
the standby mode, the setting is not effective to the projector. To control the projector with a web browser, the projector must be in the powered-on condition. Q Why does it sometimes take a lot of depending on the SMTP server. This projector does not support this kind of SMTP server. 55 ENGLISH - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 56
, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.46 - 47). Q What is the MAC address assigned to - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 57
Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult - Sanyo PLC-WXU300 | Owner's Manual Network for Windows - Page 58
NETWORK OWNER'S MANUAL SO-KE5AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
 |
 |
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.