Sanyo PLC-XM100/L Owner's Manual

Sanyo PLC-XM100/L - 5000 Lumens Manual

Get Sanyo PLC-XM100/L - 5000 Lumens PDF manuals and user guides View all Sanyo PLC-XM100/L manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XM100/L manual content summary:

  • Sanyo PLC-XM100/L | Owner's Manual - Page 1
    Multimedia Projector MODEL PLC-XM100 PLC-XM150 Network Supported Refer to the Owner's Manuals below for details about network function. □ Network Set-up and Operation □ PJ Network Manager PLC-XM100L PLC-XM150L  Projection lens is optional. Owner's Manual
  • Sanyo PLC-XM100/L | Owner's Manual - Page 2
    when the shutter is closed for a long time. (p.61) ♦ Corner Correction ♦ Automatic Filter Replacement Function The projector monitors the condition of the filter and replaces a filter automatically when it detects the clogging. ♦ Motor-driven Lens Shift Projection lens can be moved up, down, right
  • Sanyo PLC-XM100/L | Owner's Manual - Page 3
    and Care 63 Filter Instructions 63 Replacing the Filter Cartridge 64 Resetting the Filter Counter 65 Resetting the Scroll Counter 65 Lamp Replacement 66 Cleaning the Projection Lens 68 Cleaning the Projector Cabinet 68 Warning Indicators 69 Appendix 70 Troubleshooting 70 Menu
  • Sanyo PLC-XM100/L | Owner's Manual - Page 4
    manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER
  • Sanyo PLC-XM100/L | Owner's Manual - Page 5
    cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due
  • Sanyo PLC-XM100/L | Owner's Manual - Page 6
    indicator on the top panel lights up (see below). Stop using the projector immediately and replace the filter cartridge. Blocking the air vents and leaving the projector uncleaned for a long time may not only damage the projector and may require costly repairs but may also cause accidents or fire
  • Sanyo PLC-XM100/L | Owner's Manual - Page 7
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in
  • Sanyo PLC-XM100/L | Owner's Manual - Page 8
    other transport service, consult your dealer. - Do not put the projector in a case before it is cooled enough. Cautions in Handling the Projector Do not hold the lens or the lens compartment tube when lifting or moving the projector. Doing so may cause damage to the lens and the projector. Care must
  • Sanyo PLC-XM100/L | Owner's Manual - Page 9
    specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number Trade Name Responsible party Address Telephone No. : PLC-XM100, PLC-XM100L, PLC-XM150, PLC-XM150L : Sanyo : SANYO NORTH AMERICA CORPORATION
  • Sanyo PLC-XM100/L | Owner's Manual - Page 10
    Part Names and Functions Front ① ② ③ ④⑤ ⑥ ⑧ ⑨⑩ ⑦ ① Lens Release Button ② Indicators ③ Lamp Cover ④ Speaker ⑤ Lens Cap (for PLC-XM100, PLC-XM150) ⑥ Projection Lens (for PLC-XM100, PLC-XM150) ⑦ Lens Mount Cover (for PLC-XM100L, PLC-XM150L) ⑧ Infrared Remote Receiver (Front & Top) ⑨ Side
  • Sanyo PLC-XM100/L | Owner's Manual - Page 11
    cable (refer to the owner's manual of "Network Set-up and Operation"). ③ CONTROL PORT CONNECTOR When controlling the projector with RS-232C, connect the control equipment to this connector with the serial control cable signal from computer or video equipment to external audio equipment (p.21). ⑦ R/C
  • Sanyo PLC-XM100/L | Owner's Manual - Page 12
    focus, zoom, and lens shift adjustment mode (p.27). ⑨ LAMP indicator Light red during operations. ⑩ WARNING TEMP. indicator Blink red when the internal temperature of the projector exceeds the operating range (pp.69, 76-78). ⑪ WARNING FILTER indicator - Blink slow when the filter is being scrolled
  • Sanyo PLC-XM100/L | Owner's Manual - Page 13
    Remote Control   Part Names and Functions    ⑬ ⑭  ⑫  ⑪   ① STAND-BY button Turn the projector off (p.24). ② Wired Remote jack Connect the remote control cable (not supplied) to this jack when using as a wired remote control. ③ Signal Emission indicator Light red while a signal
  • Sanyo PLC-XM100/L | Owner's Manual - Page 14
    "ALL OFF" for power saving when it is not in use. Slide this switch to "RESET" to initialize the remote control code. ㉑ FILTER button Scroll the filter (p.30). ㉒ LENS SHIFT button Select the Lens Shift function (p.29). ㉓ FREEZE button Freeze the picture on the screen (p.30). ㉔ P-TIMER button
  • Sanyo PLC-XM100/L | Owner's Manual - Page 15
    replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector and the projector with the remote control cable (sold separately). Connected with the remote control cable, the remote
  • Sanyo PLC-XM100/L | Owner's Manual - Page 16
    several projectors or video equipment next to each other are operated at the same time. Change the remote control code for the projector first code, slide the RESET/ ON/ ALL-OFF switch to "RESET", and then to "ON". The initial code is set to Code 1. MENU button Number buttons (1-8) RESET/ON/ALL OFF
  • Sanyo PLC-XM100/L | Owner's Manual - Page 17
    Projector For projector positioning, see the figures below. The projector 73 m) 16.5' (5.03 m) 10.9' (3.34 m) 4.3'(1.30 m) 150" 100" 89" 59" 40" 200" 118" 300" Max. Zoom 300" Lens Shift Adjustment Projection lens can be moved from side to side and up and down with the motor-driven lens shift
  • Sanyo PLC-XM100/L | Owner's Manual - Page 18
    using an optional lens, install the lens by following the instructions below. Ask the sales dealer for detailed information of the optional lens specifications. Removing the lens 1 Shift the lens to the center position by using the Lens shift function (p.27). 2 Turn off the projector and unplug the
  • Sanyo PLC-XM100/L | Owner's Manual - Page 19
    • Monitor Output Monitor Output USB port BNC cable Serial Cross cable VGA cable VGA cable DVI-Digital USB cable cable G B R H/V V CONTROL PORT ANALOG OUT ANALOG IN DIGITAL IN USB Unplug the power cords of both the projector and external equipment from the AC outlet before connecting
  • Sanyo PLC-XM100/L | Owner's Manual - Page 20
    to Video Equipment (Video, S-video) Cables used for connection ( = Cables not supplied with this projector.) • Video cable (RCA x 1 or RCA x 3)  • BNC cable (BNC x 1 or BNC x 3)  • S-video cable  • Scart-VGA cable • DVI-Digital cable  Unplug the power cords of both the projector and
  • Sanyo PLC-XM100/L | Owner's Manual - Page 21
    Connecting for Audio Signal Cables used for connection ( = Cables not supplied with this projector.) • Audio cable  Installation Audio Output Audio Output (R) (L) (R) (L) External Audio Equipment Audio Input Audio Audio cable cable (stereo) (stereo) Audio cable Audio cable (stereo) AUDIO IN
  • Sanyo PLC-XM100/L | Owner's Manual - Page 22
    Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200- 240 V AC authorized dealer or service station. Connect the projector with all peripheral equipment before turning on the projector. CAUTION The AC outlet must be near this equipment and must be
  • Sanyo PLC-XM100/L | Owner's Manual - Page 23
    Note: • The Lamp replacement icon and the Filter replacement or the Filter cartridge replacement icon may appear on the screen depending on the usage state of the projector. • When the filter cartridge replacement icon keeps appearing on the screen at turning on the projector for some time and no
  • Sanyo PLC-XM100/L | Owner's Manual - Page 24
    of this manual and keep it on hand. Should the PIN code be missing or forgotten, consult your dealer or service center. Turning Off the Projector 1 Press LAMP LIFE. DO NOT OPERATE THE PROJECTOR CONTINUOUSLY WITHOUT REST. CONTINUOUS USE MAY RESULT IN SHORTENING THE LAMP LIFE. TURN OFF THE PROJECTOR
  • Sanyo PLC-XM100/L | Owner's Manual - Page 25
    Menu The projector can be adjusted setting procedure, refer to respective sections in this manual. Side Control MENU button SELECT button 1 Press Image 10 Point ► or SELECT button The currently set item is check marked. Network Standard Real Image 1 Image 2 Image 3 Image 4 Image 5 Image 6
  • Sanyo PLC-XM100/L | Owner's Manual - Page 26
    V-sync freq., Screen, Language, Lamp status, Lamp counter, Filter counter, Power management, Key lock, PIN code lock, Shutter management, Simple mode, Remote control, and SERIAL NO. (p.29).  Network See the owner's manual of "Network Set-up and Operation".  Guide The key operation is displayed. 26
  • Sanyo PLC-XM100/L | Owner's Manual - Page 27
    Operating with Projector Control Lens Operation The following lens operation can be made with the Lens button on the side control. Press the LENS button to enter each lens operation mode. The selected adjustment display appears on the screen. Zoom → Focus → Lens Shift Side Control LENS button
  • Sanyo PLC-XM100/L | Owner's Manual - Page 28
    Basic Operation Sound Adjustment Direct Operation Side Control Volume Press the VOLUME+/- buttons on the side control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE (Point ▼) button on the remote control to select
  • Sanyo PLC-XM100/L | Owner's Manual - Page 29
    page 43 for details. LENS SHIFT button See page 27 for image. ZOOM buttons LENS SHIFT button FOCUS buttons projector and the signal being projected through the projector service the projector. Information Menu Network Input H-sync freq. V-sync freq. Screen Language Lamp status Lamp counter Filter
  • Sanyo PLC-XM100/L | Owner's Manual - Page 30
    . To stop the count time, press the P-TIMER button FILTER button Press and hold the FILTER button for more than five seconds to operate electrically operated filter to replace the filter. Note: • The filter cannot be rewound. • When the filter is replaced, the total accumulated time of the filter
  • Sanyo PLC-XM100/L | Owner's Manual - Page 31
    the AUTO PC button on the remote control, correct the image manually as follows: Press the KEYSTONE button on the remote control to functions cannot be adjusted at the same time. If one of the fuctions is adjusted, and then the other one will be reset automatically. The top left corner adjustment as
  • Sanyo PLC-XM100/L | Owner's Manual - Page 32
    (p.19). When the Pointer function is used, the wireless mouse is not available. 2 When a USB cable is connected to the computer and the projector, turn on the projector first, then the computer. If you turn on the computer first, the wireless mouse function may not operate properly. MOUSE POINTER
  • Sanyo PLC-XM100/L | Owner's Manual - Page 33
    , the INPUT button is used for switching input source. The input source changes each time you press the INPUT button on the side control or the remote control as follows: INPUT 2 button Input 2 Remote Control RGB (PC analog) Video RGB (Scart) RGB (PC digital) Y,Pb/Cb,Pr/Cr RGB INPUT buttons RGB
  • Sanyo PLC-XM100/L | Owner's Manual - Page 34
    Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. INPUT (Scart) RGB(PC digital) RGB(AV HDCP) RGB(PC analog) RGB Video Auto RGB(PC analog) RGB Video SVGA 1 WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS ) When connecting
  • Sanyo PLC-XM100/L | Owner's Manual - Page 35
    set to RGB input manually. WHEN SELECTING INPUT 3 (AV TERMINALS ) When connecting to video equipment, select the type of Video source in the Source Select Menu. Video When the video input signal is connected to the VIDEO jack, select Video. Y,Pb/Cb,Pr/Cr When the video input signal is connected
  • Sanyo PLC-XM100/L | Owner's Manual - Page 36
    between your computer and the projector. (See "Troubleshooting" on pp.70-72.) Mode 1 The preset system is manually adjusted in the PC adjust Video System SVGA 1 The PC System Menu Selected system is displayed. Selecting Computer System Manually PC system can also be selected manually
  • Sanyo PLC-XM100/L | Owner's Manual - Page 37
    projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See "Manual of signals and the type and length of cables, the signals may not be properly viewed. mode Clamp Display area H Display area V Reset Mode free Store 0 1366 0 0 0 1024
  • Sanyo PLC-XM100/L | Owner's Manual - Page 38
    those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to 768 adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Reset Mode free Store Fine sync Use the Point ◄► buttons to adjust the value,
  • Sanyo PLC-XM100/L | Owner's Manual - Page 39
    sync Total dots Position H Position V Current mode Clamp Display area H Display area V Reset Mode free Store 0 1366 0 0 0 1024 768 This mode has stored parameters. System Menu (p.36). • When input computer signal to the projector, PC adjust function will become available. Press the MENU button to
  • Sanyo PLC-XM100/L | Owner's Manual - Page 40
    select the desired item and then press the SELECT button. Standard Normal picture level preset on the projector. Real Picture level with improved halftone for graphics. Image 1-10 User preset picture adjustment in the Image adjust Menu. (p.42) Image select Menu Standard Real Image 1 Image 2 Image
  • Sanyo PLC-XM100/L | Owner's Manual - Page 41
    the gamma value to obtain a better balance of contrast (from 0 to 15). Selected Image mode Contrast Brightness Color temp. Red Green Blue Offset Sharpness Gamma Reset Store 32 32 High 28 32 35 8 8 Use the Point ◄► buttons to adjust the setting value. Note: When White balance Red, Green or Blue
  • Sanyo PLC-XM100/L | Owner's Manual - Page 42
    Rear Reset video signal at 16:9. 42 Note: • The projector cannot display any resolution higher than 1920 x 1200. If your computer's screen resolution is higher than 1920 x 1200, lower the resolution before connecting the projector. • The image data other than XGA (1024 x 768) is modified to fit
  • Sanyo PLC-XM100/L | Owner's Manual - Page 43
    screen image. Custom Adjust the screen scale and position manually with this function. Press the Point ►button at is selected, the saved scale is used. Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at Yes.
  • Sanyo PLC-XM100/L | Owner's Manual - Page 44
    the keystone correction even when the AC power cord is unplugged. Reset........ Release the keystone correction when the AC power cord is unplugged. reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be left
  • Sanyo PLC-XM100/L | Owner's Manual - Page 45
    and then press the SELECT button. System NTSC Video Jack or S-video Jack Video Auto The projector automatically detects an incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If
  • Sanyo PLC-XM100/L | Owner's Manual - Page 46
    Video Input Image Level Selection Menu Operation 1 Press the MENU button to display then press the SELECT button. Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. Image 1-10 User preset picture adjustment in the Image adjust Menu. (p.48) Image
  • Sanyo PLC-XM100/L | Owner's Manual - Page 47
    Reset Store Use the Point ◄► buttons to adjust the setting value. 32 32 32 32 High 28 32 35 8 8 1/2 Note: • When White balance Red, Green or Blue is adjusted, the Color temp. level will change to Adj. • Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.45
  • Sanyo PLC-XM100/L | Owner's Manual - Page 48
    mode is Off. On Noise reduction mode is On. Progressive An interlaced video signal can be displayed in progressive mode. Press the Point ◄► buttons to this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the
  • Sanyo PLC-XM100/L | Owner's Manual - Page 49
    Normal Provide the image to fit the screen size while maintaining the the screen scale and position manually with this function. Press the Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at "Yes". Custom Video
  • Sanyo PLC-XM100/L | Owner's Manual - Page 50
    Video the keystone correction even when the AC power cord is unplugged. Reset....... Release the keystone correction when the AC power cord is unplugged. reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be
  • Sanyo PLC-XM100/L | Owner's Manual - Page 51
    Input button Display Background Logo Lamp control Filter control Fan control Simple the following situation: - When turning on the projector by pressing the ON/ STAND-BY button on Mode 1 or Mode 2, the status of Input and Lamp are displayed every time the signal is switched. •Only the last selected
  • Sanyo PLC-XM100/L | Owner's Manual - Page 52
    when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright . . Project a black background. It is invalid when there is no image. Off User . . . Project an image captured in the Logo setting. Logo (Logo and Logo
  • Sanyo PLC-XM100/L | Owner's Manual - Page 53
    can be captured up to XGA (1024 x 768). A signal from video equipment can be captured except for 720p, 1035i, 1080i and 1080p. • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone
  • Sanyo PLC-XM100/L | Owner's Manual - Page 54
    -digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, Logo PIN code and the number will turn red for a moment. Enter the correct Logo PIN code
  • Sanyo PLC-XM100/L | Owner's Manual - Page 55
    Mode 2 has been selected and the projection lamp exceedes the recommended total hours of use, the replacement icon will be displayed at the time of power-on. Then the projector will turn off after 3 minutes. Lamp replacement icon The Lamp replacement icon will not appear when the Display
  • Sanyo PLC-XM100/L | Owner's Manual - Page 56
    filter is being scrolled. • The filter cannot be rewound. Back • When the filter is replaced, the total accumulated time of the filter to fit the code on the projector. • If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. 56
  • Sanyo PLC-XM100/L | Owner's Manual - Page 57
    Select Eco when you do not use the projector via network. The projector's network function will stop when turning off the projector. Refer to the owner's manual of "Network Set-up and Operation". Note: • Factory default is Network. • When selecting Network, the cooling fans may be running depending
  • Sanyo PLC-XM100/L | Owner's Manual - Page 58
    projector properly (see "Turning Off the Projector" on page 24). If the projector Count down......... The time set in the Video delay control Filter counter Test pattern Factory default P-Timer Count up Count down Timer Start Reset Exit P-Timer Count up Count down Timer Start Reset Exit 58 Network
  • Sanyo PLC-XM100/L | Owner's Manual - Page 59
    unlock, use the side control. Video delay control Off If the side control accidentally becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Off PIN code lock
  • Sanyo PLC-XM100/L | Owner's Manual - Page 60
    -digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, PIN code and the number will turn red for a moment. Enter the correct PIN code all over again
  • Sanyo PLC-XM100/L | Owner's Manual - Page 61
    Standby mode On start Pointer P-Timer Security Shutter Video delay control Filter counter Test pattern Factory default Network On Dot Off Shutter Protection Projector Remote control Management Off Off 180 Min Video delay control Press the SELECT at Video delay control, and then use the Point
  • Sanyo PLC-XM100/L | Owner's Manual - Page 62
    is necessary. If the filter is out of scroll and the projector reaches a time set in the timer setting, Fig. 2 appears on the screen, indicating that the filter cartridge replacement is necessary. Filter counter reset..When replacing the Filter cartridge, reset the Filter counter and the Scroll
  • Sanyo PLC-XM100/L | Owner's Manual - Page 63
    in internal heat buildup and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to replace the filter easily. The projector monitors the condition of the filter at all time and replaces a filter with a new one automatically when it detects
  • Sanyo PLC-XM100/L | Owner's Manual - Page 64
    or service station for proper cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Replacement filter cartridge can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector PLC-XM100, PLC-XM150, PLC-XM100L, PLC-XM150L ● Replacement
  • Sanyo PLC-XM100/L | Owner's Manual - Page 65
    appears. Select Yes, then another confirmation box appears. Select Yes again to reset the Filter counter. Resetting the Scroll Counter Be sure to reset the Scroll counter after replacing the filter cartridge. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select
  • Sanyo PLC-XM100/L | Owner's Manual - Page 66
    Maintenance and Care Lamp Replacement When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is
  • Sanyo PLC-XM100/L | Owner's Manual - Page 67
    to the dealer. ● Model No. of your projector : PLC-XM100, PLC-XM150 PLC-XM100L, PLC-XM150L ● Replacement Lamp Type No. : POA-LMP137 (For PLC-XM100 / XM100L) (Service Parts No. 610 347 5158) POA-LMP136 (For PLC-XM150 / XM150L) (Service Parts No. 610 346 9607) 67
  • Sanyo PLC-XM100/L | Owner's Manual - Page 68
    the surface of the lens. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning. Gently wipe the projector body with a soft AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal
  • Sanyo PLC-XM100/L | Owner's Manual - Page 69
    been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent. - Is the filter clean? Replace the filter with a new one. The projector is shut down and the LAMP indicator is lighting and other indicators are blinking. When the
  • Sanyo PLC-XM100/L | Owner's Manual - Page 70
    Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. 1. Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21. 2. Check the cable connection. Make sure that all computers, video equipment
  • Sanyo PLC-XM100/L | Owner's Manual - Page 71
    is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 64-65) appears on the screen The image is out of focus. - Adjust the focus of the projector. - Check Projection Lens to see if it needs cleaning. Note: Moving the projector from a cool temperature location to
  • Sanyo PLC-XM100/L | Owner's Manual - Page 72
    center. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the
  • Sanyo PLC-XM100/L | Owner's Manual - Page 73
    Network * S-video * Network will be displayed only when an optional PJ-Net Organizer is attached. Sound Sound Information Information Volume Built-in SP Mute 0-63 On/Off On/Off Input H-sync freq. V-sync freq. Screen Language Lamp status Lamp counter Filter Sharpness Gamma Reset Store 0-63
  • Sanyo PLC-XM100/L | Owner's Manual - Page 74
    Appendix Screen Screen Normal True Wide Full Custom Digital zoom + Digital zoom Keystone Ceiling Rear Reset Scale H & V Position Common Reset H / V On/Off H / V Store Reset On/Off On/Off Video Input System (2) Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL-N Image adjust Image adjust Contrast
  • Sanyo PLC-XM100/L | Owner's Manual - Page 75
    lock Off/On1/On2 PIN code change Shutter Protection Remote control Projector On/Off On/Off Management 5 - 180 Min. Video delay control Off/Low/Mid/High Filter counter Filter counter H Timer Off/400H/700H/1000H Filter counter reset Yes/No Scrolls remaining Scroll(s) Scroll counter
  • Sanyo PLC-XM100/L | Owner's Manual - Page 76
    Condition Check the indicators for the projector condition. The projector is operating normally. POWER green LAMP red Indicators WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP REPLACE orange Projector Condition The projector is off. (The AC power cord is unplugged.) ❖  The
  • Sanyo PLC-XM100/L | Owner's Manual - Page 77
    this indicator lights orange, replace the filter or the filter cartridge with a new one promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.65). LAMP REPLACE When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange. When
  • Sanyo PLC-XM100/L | Owner's Manual - Page 78
    WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP REPLACE orange Projector Condition   Fig.2 Filter replacement icon Fig.3 Fig.4 Filter cartridge replacement icon ❖   If the Filter counter reached a time set in the timer setting, a Filter replacement icon (Fig.2) appears on
  • Sanyo PLC-XM100/L | Owner's Manual - Page 79
    Basically this projector can accept SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA 15 MAC 19 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 33.750 28.125 33.750 28.125 27.000 67.5000 56.250 33.750 28.125 27.000 V-Freq.(Hz)
  • Sanyo PLC-XM100/L | Owner's Manual - Page 80
    the DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D- on the condition of signals and the type and length of cables, these signals may not be properly viewed. • Specifications are subject
  • Sanyo PLC-XM100/L | Owner's Manual - Page 81
    (for PLC-XM100/PLC-XM150) Lens Mount Cover (for PLC-XM100L/PLCXM150L) Lens Antitheft screw * VGA Cable PIN Code Label * Contact the dealer where you purchased the projector or the service center about the Lens Antitheft Screw. ● The specifications are subject to change without notice. ● LCD panels
  • Sanyo PLC-XM100/L | Owner's Manual - Page 82
    It may cause serious damage to the projector. To the sales and service engineers: For the lens replacement and lens installation, refer to the installation manual of the optional lens. Before replacing and installing the lens, make sure that you are using the lens with the correct Type No. PJ Link
  • Sanyo PLC-XM100/L | Owner's Manual - Page 83
    Appendix Configurations of Terminals ANALOG/ MONITOR OUT (Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 Input 1 Red Input 2 Green Input 3 Blue Input 4 No Connect 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) Output 1 Red Output 2 Green Output 3 Blue Output 4 No
  • Sanyo PLC-XM100/L | Owner's Manual - Page 84
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo PLC-XM100/L | Owner's Manual - Page 85
    PLC-XM100L, PLC-XM150L 6.25(158.8) 3.78(96.0) Dimensions (3.54)90.0 (3.94)100.0 (18.58)472.0 (19.27)489.5 (3.31)84.0 (5.76)164.0 Appendix Unit: inch (mm) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) (5.31)135.0 (3.54)90.0 (14.57)370.1 PLC-XM100, PLC-XM150 6.25(158.8) 3.78(96
  • Sanyo PLC-XM100/L | Owner's Manual - Page 86
    's operations by using the RS-232C serial port. Operation 1 Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC. (See p.19) 2 Launch a communication software provided with PC and setup the communication condition as follows: Baud rate Parity check
  • Sanyo PLC-XM100/L | Owner's Manual - Page 87
    projector ON Turn the projector OFF (immediately OFF) Turn the projector OFF Select Input 1 Select Input 2 Select Input 3 Select Network Volume + Volume Sound mute ON Sound mute OFF Video mute ON Video (AV HDCP) Lens shift UP Lens shift DOWN Lens shift LEFT Lens shift RIGHT Auto PC adj. Keystone UP
  • Sanyo PLC-XM100/L | Owner's Manual - Page 88
    anomaly Cooling down at Power Management mode Power Management mode after Cooling down Cooling down after the projector is turned off when the lamps are out. Stand-by mode after Cooling down when the lamps are out. Stand-by mode after Cooling down at the temperature anomaly. Cooling down when the
  • Sanyo PLC-XM100/L | Owner's Manual - Page 89
    KA8AL
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Owner’s Manual
Projection lens is optional.
Multimedia Projector
MODEL
PLC-XM100
PLC-XM150
PLC-XM100L
PLC-XM150L
Network Supported
Refer to the Owner's Manuals below for
details about network function.
□
Network Set-up and Operation
□
PJ Network Manager