Sanyo PLC-XM100/L Owner's Manual Network Setup

Sanyo PLC-XM100/L - 5000 Lumens Manual

Get Sanyo PLC-XM100/L - 5000 Lumens PDF manuals and user guides View all Sanyo PLC-XM100/L manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XM100/L manual content summary:

  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 2
    speci- fied in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-XM100, PLC-XM100L, PLC-XM150, PLC-XM150L Trade Name : Sanyo Responsible party : SANYO NORTH AMERICA CORPORATION Address : 21605
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 3
    Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 4
    contents Compliance...2 Federal Communications Commission Notice 2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9 Chapter 2 Setup Procedures 11
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 5
    Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH 
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 6
    projector functions PC1 PC2 such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 7
    projector via networks, computers should meet the operating environment below. Computer environment Operating System Recommended CPU Memory HDD free area Drive equipment Display setting of computer Network drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 8
    operation depending on your computer environment. Use of this manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 9
    start browser configurations. ➔ "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to operate the projector. ■ Operate and manage the projector ➔ "4. Controlling the projector" (pp.31-44) ➔ "Power Control and status check" (p.32) ➔ "Control
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 10
    Chapter 1 Preparation 10
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 11
    Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 12
    Orange) Blink orange when the projector is sending or receiving the data. LINK Lamp (Green) Light green when the projector is connected to the network correctly. LAN Cable Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 13
    DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 14
    PIN code is to restrict the access to the projector through the network. After setting the Network PIN code, you need to enter it to operate the projector via the networks. 1. Select "Network PIN code" in the Network menu, and press SELECT button. The Network PIN code screen will appear. 2. Set the
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 15
    factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" SUBNET MASK GATEWAY ADDRESS DNS ADDRESS Settings Off 169.254.100.100 255.255.0.0 255.255.255.255 255.255.255.255 15 ENGLISH
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 16
    Chapter 2 Setup Procedures 16
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 17
    Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 18
    PIN code onto the Password text area and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and the next main setting
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 19
    Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 20
    3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 21
    Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 22
    the setting page. English or Japanese. Model name........Indicates the model name of the projector SERIAL NO. ..........Indicates the serial number of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink password authentication on
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 23
    click Set button. ✐ 1 to 32 alphanumeric characters can be used for the password. What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for centralized control and monitoring. This standard was established by the Japan
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 24
    name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector. * All the network setting will reset to the default when setting [0.0.0.0] of the
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 25
    alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail To use the E-Mail function, it must be set the DNS address on the Network setting page correctly. ✐ You cannot use this E-mail function if the DNS server
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 26
    :Type and contents of alert mail" described on the next page. Option ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 27
    ✐ The projector lamp was turned off, because the projector power circuit failed. Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 28
    following message. *The projector lamp has reached replacement time. Lamp ON 2000 h ✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every poweron of the projector. This alert mail
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 29
    SNMP setting SNMP setting This projector provides a SNMP (Simple Network Management Protocol) agent function. The . PJ information Item Description Contact Enter user name of the projector etc. (optional) Place Enter place of the projector (optional) Community name(refer).......Enter community
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 30
    Set button if you tick or un-tick the check box on a page. ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 31
    Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 32
    window Item Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 33
    control it through the network. To control the projector through the network, unlock the security on the projector using with the projector's menu control. Caution about turning on/off the projector via the networks When turning on/off the projector via the networks, preset the projector as follows
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 34
    ✐ Please see the owner's manual of the projector to have the further information of Video Y, Pb/Cb, Pr/Cr RGB VIDEO : Video Y, Pb/Cb, Pr/Cr S-video ✐ The control page displays valid control items depending on the selected input mode, signal or functions of the projector
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 35
    of signal input to the projector. The available system mode signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are , D-1035i and D-1080i. Available selection at the Video/S-video/Scart input Item Description AUTO It automatically switches to
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 36
    Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speaker. (0 ~ 63) Mute
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 37
    ) Progressive S witches progressive mode (ON, OFF, Film) Reset Resets the Image adjustment to previous levels. Store Stores the Image adjustment the input mode as shown in the table left. ENGLISH Input source Image mode Video Computer Standard 4 Cinema 4 Real * Image1 - 10 4 4 * 4
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 38
    connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, screen. Vertical Adjusts the vertical position of the screen. Reset Resets the PC adjustments to the previous levels. Mode Store
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 39
    . Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item on the input mode as shown in the table below. Input source Screen mode Video Computer Normal Wide True Full Custom 4 4 4 4 * 4 * 4 4
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 40
    projector and the remote control. (Mode1, Mode2, Mode3) Background.........Sets the screen background when no signal input. (Blue, User, Lamp control......Selects lamp control mode. (Auto, Normal, Eco1, Eco2) Lamp life control Selects lamp life control mode (Mode1, Mode2) when the total use time
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 41
    up the projector Setting 3 Item Description Filter counter(h Displays the filter counter. Reset the time after filter cartridge replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. * Do not reset the Filter counter when the filter cartridge
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 42
    lock) status (Yes, No) PJ time(h) Displays the accumulated use time of the projector. Lamp Corres. Value(h) Displays the use time (Corresponding value) of the lamp. Filter time(h) Displays the accumulated use time of the filter. Filter condition Displays filter status with an icon. Refer
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 43
    used over a specified use time, replace lamp immediately) Indication of the filter status Icon display/background Status Blue Good condition. Yellow/Gray Red/Gray Filter is almost clogged. Filter is clogged. Replace a filter with new one. * When the projector cannot decode the return from
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 44
    Chapter 4 Controlling the Projector 44
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 45
    Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 45
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 46
    Mask : 255.255.255.0 Default Gateway : DNS : * UTP cross cable Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255. 0.0.0.0 DNS : 0.0.0.0 Connecting the projector (PJ01) to the control computer (PC05) via the hub. Hub To another network Computer Name: PC05 IP Address :
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 47
    .5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default 192.168.201.1 Network Group: 192.168.200.x To another network O ce Hub Hub Gateway (Router) IP Address : 192.168.200.1 IP Address : 192.168.100.1 IP Address
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 48
    *1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 49
    C0C Audio Mute off C1C Menu display on C1D menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). If the authentication of the entered
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 50
    browser preference correctly. Especially when connecting the projector and computer with a UTP cross cable directly, or when the network does not provide the proxy server, make or applications. Please see the setting instructions on next page for example and also refer to on-line help of your web
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 51
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 52
    correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked. To designate proxy settings
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 53
    on HTTP Proxy item. For further instruction please consult your network administrator. - Not using proxy server Select the item Direct connection to the Internet in the proxy setting window. If you connect the projector to the computer directly with UTP cross cable, this must be selected. To
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 54
    Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the items Web Proxy (HTTP) and Secure Web Proxy (HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 55
    (☞ p.12). - Check the connection of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong network configuration of the computer. Check the network configuration of the computer. 3. The proxy setting of
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 56
    the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP address
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 57
    display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator. Q H ow many numbers of the E-mail address can
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 58
    IP address must correlate to a network number. If network numbers are different between the equipment, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 59
    Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult your local dealer. The version number of the firmware is
  • Sanyo PLC-XM100/L | Owner's Manual Network Setup - Page 60
    NETWORK OWNER'S MANUAL SO-KA8AL SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.