Sanyo PLC-XU305A Owner's Manual Network Windows

Sanyo PLC-XU305A - 3000 Manual

Get Sanyo PLC-XU305A - 3000 PDF manuals and user guides
UPC - 086483076312
View all Sanyo PLC-XU305A manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XU305A manual content summary:

  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 2
    been tested and used in accordance with the instructions, may cause harmful interference Model Number : QXXAVC922---P Trade Name : Sanyo Responsible party : SANYO NORTH must be used for RF interference suppression. For Canadian Users This Class B digital apparatus complies with Canadian ICES-
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 3
    GmbH, declares that this WLAN Module (QXXAVC922---P) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. SANYO Sales & Marketing Europe GmbH tímto prohlašuje, že tento WLAN Module (QXXAVC922---P) je ve shodě se základními požadavky a dalšími příslu
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 4
    depending on your computer environment. Use of this manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective booklet. 
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 5
    Table of contents Compliance...2 Safety instructions...4 Table of contents...5 Operating environment and configuration 7 Required operating environment for computers 7 Network specifications of the projector 8 1. About LAN functions 9 LAN functions and the features...10 Image projecting system
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 6
    status check...64 Controls...66 PC adjustment...70 Setting up the projector...71 Timer setting...74 Projector information...77 Multi-control...79 8. Network capture functions 85 About Network of telnet...128 Web browser setting...130 Firewall setting...135 Troubleshooting...136 Terminology...143 
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 7
    Required operating environment for computers When operating the projector via the networks, computers should meet the 2000 or Windows XP 1GB or more for Windows Vista 100MB Required to support any of VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768), The color number should be either 16 bit
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 8
    Network specifications of the projector LAN Terminal Data communication speed Protocol 100Base-TX (100Mbps)/10Base-T (10Mbps) TCP/IP Wireless LAN Interface Communication Mode Data Transfer Speed Wireless Frequency (Channel) Modulation Form Protocol Security Service area IEEE802.11b/g AdHoc,
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 9
    1 Chapter 1. About LAN functions This chapter describes the features, the mechanism, and connection procedures of the LAN. 
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 10
    projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector viewer function which remotely operates the image data on the server to project through the projector. • 
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 11
    example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . 2.0 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 0.0 2.0 1.5 1.0 0.5 0.0 Computer (1) Access point Computer (2) 11
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 12
    communication mode corresponded computer: Infrastructure ■ Wireless LAN, AdHoc Communication Mode Communication mode between Wireless LAN equipment. (Communication mode via SSID/ESSID) Network Projector Wireless communication mode :AdHoc Wireless communication mode corresponded computer: AdHoc 12
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 13
    Computer(2) Computer (3) ✳ Operate the computer mouse with the remote control. When the projector's remote control employs mouse operating function, you can operate the computer by the remote control. To use the remote control, point to the projector. You do not need to connect the USB cable to
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 14
    Chapter 1 About LAN functions 14
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 15
    2 Chapter 2. Setup procedures This chapter describes how to install the Network Capture 5 software and how to set up the networks. 15
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 16
    Chapter 2 Setup procedures To use the projector via the networks, follow the setup procedures below. STEP 1 Install the software on computers. Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install. STEP 2 Select Wired LAN or
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 17
    into your computer to use the Network Capture function . Please install the software as follows. Note: To install the software into the computer with Windows 2000, Windows XP or Windows Vista, you should logon as administrator. Before installation, make sure that the other applications are
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 18
    Chapter 2 Setup procedures As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing. During the installation, following window may appear, click Continue Anyway button. 3 Click Finish to complete the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 19
    1): Converts to the JPEG*1 data format which can be projected with the projector from the JPEG, bitmap and Power Point files. ● Network Viewer 5 ( servers. * To uninstall these software, use "Add/Remove Program" from the control panel. *1 This product supports the JPEG image format. This file
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 20
    Panel". ● Network Viewer 5 (File Converter 2): This is a kind of the printer driver to convert to the JPEG data optimized to project by the projector from any of the documents created by the application software. * To uninstall Network Viewer 5 (File Converter 2), just delete the "Network Viewer
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 21
    3 Chapter 3. Names and functions of the operation screen This chapter describes the functions of each part of the operation screen. 21
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 22
    Chapter 3 Names and functions of the operating screen Network connection standby display Turn on the projector and select either "Wired" or "Wireless" from the input menu of the projector. The "Please wait..." message will be displayed on the screen. After short time, the network connection standby
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 23
    capture function. After double-clicking on a projector name, the web browser gets activated and the projector setup screen will be displayed. Note on Windows Vista When you use the Network Capture 5 software with Windows Vista, the warning dialog "User account control" will appear. In that case
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 24
    a computer user as a moderator. !0 Join moderator's group button Join the moderator's group which is selected in the Network Projector list. It network adaptor selecting window will appear each time the Network Capture 5 software starts. Select a network adaptor and check the "Set network adaptor
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 25
    4 Chapter 4. Wired LAN configurations This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment. 25
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 26
    to the LAN line Connect the LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal LINK/ACT Lamp (Orange) Light or blink orange when the projector is connected to the network. LAN Cable Speed Lamp (Green) Light according to the speed of the connected network. 10 Base
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 27
    DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 28
    location separated by the router, see next page. When Firewall function (Anti-virus software) is effective, network projector may not be found. In that case, disable the Firewall function and try searching again. ✳ If the projector is named, the name will be displayed. The name can be set with the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 29
    Add button, "IP address set up" window appears. Enter the IP address of the projector and Click OK button. Then, the projector will be added on the "Search specified IP address" window. Multiple projectors are registered and they are stored even when the application is closed. 3. Click OK button
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 30
    you do not want to set the Network PIN code, set "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See "6. Basic setting and operation" ➔ "Initial setting" ➔ "Network PIN code setting
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 31
    Wired LAN factory default settings Wired factory default Select "Wired factory default" in the Network menu and press SELECT button. All the wired LAN settings will go back to the factory default settings. For details, refer to "Wired LAN factory default settings" (p.32). 31
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 32
    Chapter 4 Wired LAN configurations Wired LAN factory default settings Parameter Wired 1 SELECTED LAN Wired 2 IP CONFIGURATION MANUAL DHCP Wired 3 MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 33
    equipped with a Wireless LAN card adapter which supports IEEE 802.11b/g. If connecting in Infrastructure mode with an access point, the access point is required to support IEEE 802.11b/g. Caution: Do not use a mobile phone or PHS near (within 20cm/8inch) the projector. It may cause malfunction. 33
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 34
    button to set. SSID/ESSID for the network type "Infrastructure" and "AdHoc" are required to be entered the same characters into the projector, the access point, and the Wireless LAN compatible computer (up to 32 characters). Characters can be selected from A~Z, a~z, blank (space), 0-9, or - (hyphen
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 35
    of WEP, WPA-PSK, WPA2-PSK security, select "Next". Refer to "Configuring security with the projector" on next page for details. Item Description DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When its set On, IP address, Subnet, Gateway and DNS are
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 36
    to move among the items and adjust setting; use the Point 7 8 buttons to move among the character positions of the key entry fields. This projector provides the following security options. Use optimum security option on your network environment. WEP64(40)bit Open WEP64(40)bit Share WEP128(104)bit
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 37
    Configuring security with the projector Use of security type "WEP" 1. Use the Point ed buttons to select "WEP" security type. 2. Select "Key index". Use the Point ed buttons to choose
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 38
    -PSK" and "WPA2-PSK" modes are not available when the "AdHoc" network type is selected. * When you set the PSK keys with 64 digits, the projector checks whether all of the entered PSK keys are in Hex code or not. If any of the ASCII code is included in the entered
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 39
    XP and Windows Vista, and cannot be used with Windows 2000. Windows XP should be Service Pack 1 or later version. Setting Procedures 1. Turn on the projector and select "Network" in the Input menu of the projector. 2. Select "LAN mode select" in the Network menu, and press SELECT button. 3. Select
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 40
    Configurations" ➔ "Network PIN code" (p.30). Network information Display the current LAN connecting environment. Select "Network Information" from the projector menu and press SELECT button. Wireless Information (Example) Wireless factory default Select "Network factory default" in the Network menu
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 41
    wireless communication is established with the access-point or the computer in the network, the WIRELESS indicator on the top panel lights up. While the projector scans the equipment in the network, the WIRELESS indicator blinks. WIRELESS indicator 41
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 42
    default settings for Wireless 4, Wireless 5, and Wireless Simple as follows. Setting Items Wireless 4 Selected LAN Wireless 5 Wireless Simple IP CONFIGURATION MANUAL DHCP MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 169.254. * . * SUBNETMASK 255.255.0.0 255.255.255.0 255.255
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 43
    and operation Describes basic operation and settings below by using the web browser. • Initial setting Setup the basic setting such as Projector name, Network PIN code, Time setting, etc. • Network setting Configure Wired/Wireless LAN environment. • E-mail Setting Configure E-mail function to
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 44
    area and the login Network PIN code onto the Password text area and then click OK button. * The entered User Name must be "user" and it can not be changed. [Note] When the projector is accessed for the first time or the Network PIN code "0000" is set, the auto-login is performed
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 45
    . Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected (p.48) ✐T his Standard mode display is mainly used through this manual for the setting and control description. ✐If your computer does not have
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 46
    in the folder or program. How to use the setting page To control and set up the projector, use the setting menus on the web browser. The basic operation and procedures commonly used on this manual are described below. Example of the Setting Page The setting pallet appears after clicking the item
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 47
    Type of the setting pallet Text box setting Enter the number or text and then click Set button. or Change a value with s or t button and then click Set button. The value changes quickly when s or t button is kept pressing. Pull-down menu setting Select an item with pull-down menu button and then
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 48
    display language on the setting page. English or Japanese. Model name Indicates the model name of the projector. Projector name.......Sets the name of projector. This projector name is listed on the application window of the Network Capture software. Network PIN code Sets the Network PIN code to
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 49
    owner's manual for further details of the PJLink function. ✐ 1 to 32 alphanumeric characters can be used for the password. What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for centralized control and monitoring
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 50
    . The timer icon appears when time is set up correctly. Current time Indicates current date and time set on the projector Date Sets date in manual Time Sets time in manual Date and time setting NTP is abbreviated expressions of Network Time Protocol. It is a protocol to acquire the exact current
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 51
    Default Setting". Item Description Change setting.......Selects LAN1 to LAN5 and Simple IP configuration......Sets DHCP or Manual IP address Sets IP address of the projector Subnet mask............Sets Subnet mask. Default gateway*1...........Sets IP address of the default gateway (Router) DNS
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 52
    up manually if the DNS address information is not provided on your DHCP server. When selecting "Manual", configure all the items manually. to the login page again in 20 seconds. On the screen of the projector, the "Please wait..." message will appear and switching operation will start. Switching
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 53
    though all characters on the Wireless information is uppercase, it is necessary to distinguish between upper case and lower case characters. Channel If you use the projector in 802.11AdHoc mode, select the channel, from 1 to 11. 53
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 54
    Chapter 6 Basic setting and operation Configuring wireless LAN security setting Click page [3] of setting pages. Following wireless LAN security setting can be done. After completing the configuration, press Set button. Item Description Network security....Sets the type of encryption. Following
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 55
    setting E-mail setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 56
    When PJ lamp is off. o When PJ lamp replacement time is user operation" signifies that the projector is turned on by using the web browser [3 o When lamp Corres. Value reaches [ ] hours. Attached message and then it is turned into standby with ON/STANDBY button on the top control or the remote
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 57
    2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The Projector lamp is turned off, because Projector power circuit is failed. Unplug the Projector from AC outlet and ask servicing to qualified service personnel. MAIN, P-FAIL
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 58
    Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The PJ lamp replace time is reached. ✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 59
    . Click SNMP Setting on the main menu and set up each item. PJ information Item Description Contact Enter user name of the projector etc. (optional) Place Enter place of the projector (optional) Community name(refer Enter community name (read only). Default name is "public". ✐The SNMP agent
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 60
    Chapter 6 Basic setting and operation Trap Item Description Community name Enter community name to send "Trap". Default name is "public". Trap address Enter IP address of the SNMP manager computer to receive "Trap". Up to 10 address can be registered. ✐ Up to 10 trap addresses can be
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 61
    lamp is off. o When PJ lamp replacement time lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/ STANDBY button on the top control or the remote
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 62
    Chapter 6 Basic setting and operation 62
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 63
    7 Chapter 7. Controlling the projector Describes controlling and setting of the projector by using the web browser. 63
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 64
    the "ON" or "Standby" button. PJ temp. Inside temp.A Displays the surrounding temperature of lamp in the projector. Inside temp.B Displays the surrounding temperature of panel in the projector. External temp Displays the surrounding temperature of the intake vent The warning icon will appear if
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 65
    into standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and contact a qualified service personnel for service. If the power failure occurs on the projector, "Power failure" is indicated on the status column and the information
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 66
    depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further informa- tion of each control item. Input This function is to select the input mode and source mode of the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 67
    function is to select the system of signal input to the projector. The available system mode are listed on the pull-down computer system of the input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal listed. Available selection at the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 68
    Chapter 7 Controlling the projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 69
    Controls Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speakers. Mute Suppresses the sound. 69
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 70
    . This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode...........Displays a current mode like VGA, SVGA, XGA, SXGA, UXGA, WXGA, etc. or MODE1 - MODE5 are the customized mode created by
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 71
    Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting. Item Description Screen Switches the screen mode. There may not
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 72
    Lamp control...........Selects the lamp control mode. Lamp life control....Sets the lamp life control mode after exceeding the recommended total use time of the lamp. Remote control...........Sets the remote control code. Key lock Sets the prohibition of controls either Projector or Remote
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 73
    the time to indicate the filter warning message on the screen. Item Description Factory default Sets all of the projector control items to the factory default setting except the following items. Lamp Corres. Value, PJ time, Filter time, PIN code lock and Logo PIN code lock. No show Sets the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 74
    . Click Timer on the main menu. "---" will appear on the current time when the time is not set up correctly. Present time set on the projector Select date Select day Set execute time Event action How to set the timer 1 Set a day or date To set the timer event at the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 75
    event action Select an event action from the pull-down menu. Event Action ON Turns on the projector OFF Turns off the projector Lamp Normal Changes lamp mode to "Normal" Lamp Eco Changes lamp mode to "Eco" 4 Register an event Click Set button to register the set timer event. Repeat steps
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 76
    secondary events (event 4 and event 6) will become effective if a person turns off the projector (after event 3 and before event 4) or turns on the projector (after event 5 and before event 6). Invalid event Projector Power OFF ON OFF ON Invalid event OFF Event 1 Event 2 Event 3 Event 4 Event
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 77
    the basic information of the projector status. Click Information on the main menu. Items Description Input Displays selected input and source. System Displays selected signal system. Signal Input signal status Screen Displays screen mode. Lamp status Displays lamp status with an animation
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 78
    with X Red/Red with X Lamp failure (Lamp failure, check the lamp condition) Lamp failure (Lamp failure and lamp is being used over a specified use time, replace the lamp immediately) Items Description PJ time Displays the accumulated use time of the projector. Lamp Corres. Value Displays the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 79
    can control and set up them together. Click Multi Control on the main menu to display the control page. Note:  To control the multiple projectors, each projector must be set the same Network PIN code. Example of multi control PJ1 PJ2 PJ3 PJ4 PC6 PC5 PC4 Select Input2 for PJ1 to PJ4
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 80
    Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Multi control setting OFF...........Stops multi control function ON Starts multi control function. The multi
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 81
    below. * The word "none" is displayed if the "Memo" function is used. * When you click on a listed IP address, the login page for the selected projector will be displayed with a new window. IP address Status Memo Page no. Click here to close the sub menu Check & Change
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 82
    item is not changed during using the network viewer function. It is not available with the light mode. Status If some of the registered projectors are disabled by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 83
    setting and adjust controls of each menu. The setting value is applied to the registered projectors sequentially . ✐ This is effective only if the multi control item of the registered projector is set to either "Control & Image" or "Control". Setting all together "E-mail setting", "SNMP setting
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 84
    - "Network Viewer" menu). Set the display time periods and repeat times for the auto image display. After clicking Start button, the registered projectors start playing back the auto image display in sequential. ✐ F or further information of the Auto display, see "Using the network viewer function
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 85
    8 Chapter 8. Network capture functions Network Capture is a function to display the screen image and reproduce the sound of the computer via the network. - Real Time Capture - Network Communication - Moderator Function 85
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 86
    reproduce the sound of the computer which has a Network Capture 5 software by the projector through the network. This function has 3 kinds of mode as sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 87
    . Capture transfer Transfers the screen image of the computer to the projector. The captured image edit window appears on the computer screen. Select Parameter set up Sets the communication parameter between the computer and projector. For further information, see item "Parameter set up" on
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 88
    a capturing picture quality among "High, "Medium", "Low" q Reduce image........ Check if the capturing image resolution is more than projector's panel resolution (XGA), q Layer window capture.. Check if layer window image capturing. Capture start up time....... Sets the delayed time from the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 89
    you capture the screen image of the movie player software with the real time capture function, the projector may not be able to reproduce the sound. To reproduce network environment and data volume of the image. It cannot be supported for movie pictures. ✐ If you start capturing with the Select capturing
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 90
    Capture 5. 2 Select the projector(s) listed on the projector list on the application window and real time. * You can select multiple projectors (up to 5) on the projector list. • To stop capturing, click ). ✐ The sound output from the projector can be controlled with the volume slider and
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 91
    PC1 with PJ2. PC6 * Star t capturing of the PC1 from the PC5. Select "Network" as input mode previously. 1 Access to the control page of the projector by using the web browser. From the Network menu, click Capture tab to display the setting page. 2 Select the computer number from the pull-down
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 92
    If the error message appears, check item "Parameter set up" (+ p.88). ✐The projector does not provide the function to register the IP address of the computer and to set the (☞ p.89). ✐The remote control which is provided with the projector does not have the mouse operating function. 92
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 93
    , the real-time capture will not start, but will become standby status. Release the wireless LAN SIMPLE setting of the projector which is not for the real-time capture. ✐ When the software of Network Capture 5 is not installed in the computer, the sound data is not transferred. If you want to
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 94
    instructions of the wireless mouse, please refer to the projector's owners manual. Software:  The Network Capture 5 is activated. Using the Network Communication This Network Communication is to communicate by sharing the captured image of a computer with multiple computers and a projector. Users
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 95
    Auto search subject PC is "ON". If "OFF", change mode to "ON". * Projector can find up to 30 computers in the network. [2] When serving the capture data to can be registered to the projector. ✐To display the served capture data, the software Network Capture 5 must be installed on the computer. 95
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 96
    Editing window Control Capture transfer Captures a screen image and sends it to the projector Authority Acquires/releases the authority to edit the capture image Edit Tool Pencil Selects editing window on foreground always Help Version information Displays software version number 96
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 97
    tool bar Width (Large, Medium, Small) Translucence ✐ To switch the tool bars displaying on or off, select each command from menu "Display"-"Tool bar". ✐ User can realign and join the tool bars (Standard, Shape, Color, Attribute), and change it to the floating pallet by a drag and drop of the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 98
    Start Communication button. The application window disappears and the capture editing window with a captured image appears on the computer screen. The projector displays captured image on the screen. ✐ If an error message appears, check the item "Parameter set up". (☞p.88) Join the communication
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 99
    Edit capture image How to use the Network communication Drawing figures 1 Click " :Pencil" button on the form tool bar. 2 Select its attribute (shape, width, color and translucence) from the form and attribute tool bar. 3 Drag a mouse pointer on the screen image to draw the figure. Erase drawn
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 100
    Chapter 8 Network capture functions Drawing letter 1 Click " :Letter frame" button on the form tool bar. 2 Select a color of text with color tool bar. 3 Drag a mouse pointer on the screen image to specify the area of the letter frame. The letter input dialog window will appear. 4 E nter the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 101
    can be used under the environment which one or more computers are connected to the projector via the network. Preparation Start up the Network Capture 5 software on the subject computer. Set standby the projector or turn it on. Check IP address of the subject computer is registered in the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 102
    IP address of the computer has a editing authority Item Description Free Releases the editing authority forcibly ➔ Sets condition which all the users can acquire an authority Quit Quits the communication forcibly ➔ The capture editing window on all the computers closes forcibly. Update
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 103
    the participants' data directly in a short time and in real time without taking time to transfer the data to the computer connected to the projector. The image data will not be limited by the computer's application because the data transfer of each computer adopts the screen capturing system. Names
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 104
    registration button, the application window changes to "Moderator mode" window as shown in the lower picture below. Normal mode application window Projector list Status of use Moderator registration Join moderator's Pa ra m e te r group setting Moderator mode application window Status of
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 105
    's condition. On real time, On One-shot capture, On Standby, In Moderator mode, etc. User Indicates the client name (nickname or IP address) used by the projector. Error Indicates the error status during executing the real time capture or one-shot capture. Parameter set up....Sets the parameter
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 106
    application window changes "Normal mode". The column of status changes from "#On Moderating" to "On Standby". When there are multiple projectors to unregister, the application window maintains "Moderator mode" until all the registered moderator's groups are unregistered. ✳ Even after the moderator
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 107
    capture is executed. The time-out period is 10 seconds. ➔ Check the connection of the network cable. Cannot receive the data from the projector when the Start Communication, Terminate Communication, Capture transfer, Start real time capture or Terminate capture is executed. The time-out period is 10
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 108
    Chapter 8 Network capture functions 108
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 109
    Network Viewer functions Network Viewer is a function to display the image data stored in the file servers by the projector through the network. Describes the file converter software File Converter 1, File Converter 2, the program creator software Program Editor, and how to use Network Viewer. 109
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 110
    the images with the Network Viewer function, it should be converted to the optimized JPEG data for this projector. [1] How to use the Network Viewer 5 (File Converter 1) The File Converter 1 is a software to convert the images from the JPEG, bitmap or Power Point data to the optimized JPEG data for
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 111
    Menu Tree Menu Sub Menu View Tools Conversion Help Update Preview size Option Convert each file Convert a folder Version information Create the available data Description Updates contents of the preview window Sets size of the preview image, Large, Middle, Small Sets default of the output
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 112
    . Dialog window shown during using "Convert each file" and "Convert a folder" ✐ To convert images from the power point file, Microsoft Power Point software is should be installed in your computer. ✐ In the power point file conversion, all the pages are converted into JPEG files separately. 112
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 113
    Root Folder Specify the root directory of the FTP server. Normally use "/". User ID Enter your login account of the FTP sever. Password Enter your password to SXGA+) ✐ The image resolution higher than the projector's panel resolution cannot be displayed. Image rotation..........Selects image
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 114
    File Converter 2) The File Converter 2 is a kind of the printer driver software to convert to the optimized JPEG data for the projection from the any documents created by the other software such as text editor, spreadsheet or presentation software. It is possible to convert to the JPEG file from the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 115
    Network Viewer function, you can display the images in programmed order with the projector . Procedure of making program 1 To start up the Program Editor, Folder Specify the root directory of the FTP server. Normally use "/". User ID Enter your login account of the FTP sever or use blank when
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 116
    using UP or DOWN button. ✐ The programs are stored into the "DispParam" folder at the login root directory and this "DispParam" folder is made by software automatically. 7 Click Register button to register the folder list into the program. 8 Click Close button to quit the Program Editor. 116
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 117
    Creating a program file [Program Editor] Setting up the display order and time of the images In the default setting, the display order of the images is the same as ASCII code order of the file name. To change the display order or to set up the display time, take the following procedures. Display
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 118
    Chapter 9 Network Viewer functions 3 To change the display order, select*1 files and then click UP or DOWN button on the menu bar to move them onto your desired place, or select files and then drag and drop them onto your desired place with mouse. 4 To change the display time*2, select*1 files and
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 119
    menu on the web page, then connect to the FTP server and select the program name which was made at previous section. The projector starts displaying the images along the program. For further information, please see "Using the Network Viewer function" (☞ p.120). ✐ This function is not available
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 120
    Viewer function: * Should be possible to use the FTP service with Windows 2000 Professional or XP Professional. * User has a full-access account to the FTP server, or 1 Access to the control page on the projector by using the web browser. From the main menu, click Network - Viewer to display
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 121
    normally, or enter the directory name follow the "/" as shown in the below example if you have a specified directory in the server. /data/ User ID*1 Enter your login account of the FTP server Password*1 E nter your password of the FTP server Option*1 Set "Display ON" when you display
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 122
    Chapter 9 Network Viewer functions After clicking Set, the file list or preview list of the selected folder or program is displayed on the window. Decides a image to start auto display with radio button Selects a page The original image is displayed on another window by clicking on the preview
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 123
    The image in the selected folder or program is displayed on the projector's screen. The web browser opens another window and displays the preview button. * When the auto-display stops, it enables you to display the images manually by using [] button. 3. Click End button to end the auto-
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 124
    may have the alert E-mail message. For further information, please see the item "3 Option selection for sending alert mail" (☞ pp.56-58). [2] Control by the projector PC1 PC2 PJ2 Project JPEG images with PJ2. PJ1 JPEG PC3 Prog. JPEG FTP file server PC4 PC5 PC6 Select "Network" input mode
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 125
    mode" and press SELECT button, and then select "Auto" or "Manual" and then press SELECT button. When selecting "Auto", set "Display length to browse the images by using the control buttons (s,t) on the remote control or on the projector. s : Previous image display, t : Next image display 4
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 126
    Chapter 9 Network Viewer functions 126
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 127
    10 Chapter 10. Appendix Use of telnet Web browser setting Firewall setting Troubleshooting Terminology 127
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 128
    *1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of the Windows XP Professional.) 1. Select Run... submenu from Start menu on
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 129
    The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another on C1D menu display off *1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 130
    is set not to use this JavaScript function, it may not control the projector properly. In that case, the following warning message will be displayed on the top of the page. To enable the JavaScript, please see further instructions on the next page. Flash Player enable The setting page of this
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 131
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 132
    server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, it must be unchecked. 132
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 133
    Navigator is checked. Flash Player enable Flash Player Plug-in setting Select About:Plug-ins from Help menu on the web browser. The plug-ins software provided on the browser are listed on the page. Check that the Flash Player Plug-in (Shockwave Flash) is installed and set up correctly as
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 134
    to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 135
    as follows; On (recommended) checked Don't allow exceptions unchecked 3 Select Exceptions tab and check the name of Network Capture 5 listed on the Programs and Services. If there is no program name, add the program by clicking Add Program button. 4 Click OK to close setting. 135
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 136
    If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and check the relevant matters described. ■ The computer cannot connect projectors. Wired LAN Is the LAN cable connected to the projector properly? Is the LINK/ACT lamp of the LAN terminal
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 137
    5 (factory default setting) Troubleshooting Check each item below in the Wireless Setting menu of the projector as follows: *IP Address to the owner's manual for the devices or consult a system administrator of the network. Is the segment where the projector is installed different from
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 138
    the projected screen? 1. Make sure that the input mode of the projector is "Network". 2. Check the parameter set up (☞p.88). Make sure that the numbers of the capture port is the same as the projector's port number. The default port number is 9000. If the alert message "
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 139
    Troubleshooting the channel to resolve the problem. The channels of the projector and projector Client computer must be the same projector correctly, follow the procedures below; • Start up the real time capture and then start up the movie player software. • Terminate the movie player software
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 140
    names and program names (☞p.119). 5. Make sure that your computer is not using the firewall function. The projector may not be able to use the port due to this firewall function. In that case, please turn with white frame due to the paper margin of the print driver depending on the image data. 140
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 141
    ■ Sometime I have the incorrect images converted by the File Converter 2? Troubleshooting Try to change the mode to "Disable" on "Document options" - "Print optimization" item on the "Network Viewer 5 (Driver) Advance Options" in the Network Viewer 5 (FileConverter 2) Printer driver setting. 141
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 142
    - When setup as follows in a computer with Windows Vista Click start button, and click [Control Panel] - [AutoPlay], and Take no action is selected in "Software and games". - Please select the other options. - When "Autorun.inf" is denied in a computer as an anti-security measure in your local area
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 143
    Ask your system administrator whether the DHCP server is operating. ESSID (Extended Service Set Identifier) ESSID is the ID that is set to computers on 802.11b High-Rate. Only the products that have passed an inter-operation test carried by WECA is approved as Wi-Fi. Any products approved as Wi-
  • Sanyo PLC-XU305A | Owner's Manual Network Windows - Page 144
    SO-WIN-KG5AE NETWORK OWNER'S MANUAL FOR WINDOWS
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Network Set-up and Operation
For Windows
Wired and Wireless Setting
Projector Set-up and Operation
Network Capture
Network Viewer
Moderator Function
Owner’s Manual
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic operation of the
projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.