Sanyo PLC-XW15 Owners Manual

Sanyo PLC-XW15 - XGA LCD Projector Manual

Get Sanyo PLC-XW15 - XGA LCD Projector PDF manuals and user guides View all Sanyo PLC-XW15 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XW15 manual content summary:

  • Sanyo PLC-XW15 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-XW15 Owner's Manual
  • Sanyo PLC-XW15 | Owners Manual - Page 2
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS
  • Sanyo PLC-XW15 | Owners Manual - Page 3
    dropped or the cabinet has been damaged. f. When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics
  • Sanyo PLC-XW15 | Owners Manual - Page 4
    Class A digital device, pursuant with the instruction manual, may AC Power Cord supplied with this projector meets the requirement for use in plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must the safety earth symbol or coloured green or green-and-yellow. The wire which
  • Sanyo PLC-XW15 | Owners Manual - Page 5
    THE PROJECTION LENS 35 FOCUS ADJUSTMENT 20 LAMP REPLACEMENT 36 KEY STONE ADJUSTMENT 20 LAMP REPLACEMENT MONITOR TIMER 36 NO SHOW FUNCTION 21 TROUBLESHOOTING 37 PICTURE FREEZE FUNCTION P-TIMER FUNCTION 21 21 TECHNICAL SPECIFICATIONS 39 SOUND ADJUSTMENT 21 SOUND VOLUME ADJUSTMENT
  • Sanyo PLC-XW15 | Owners Manual - Page 6
    over 5 minutes. The Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed. This projector is shipped with this function ON. x Wireless Mouse The Remote Control Unit supplied with this projector has Wireless Mouse function for the
  • Sanyo PLC-XW15 | Owners Manual - Page 7
    COVER INFRARED REMOTE RECEIVER BACK OF THE CABINET TERMINALS AND CONNECTORS AIR INTAKE VENTS (Both sides and Rear) This projector is projector is used. This projector detects the internal temperature and automatically controls the operating power of the Cooling Fans. BOTTOM OF THE CABINET LAMP
  • Sanyo PLC-XW15 | Owners Manual - Page 8
    service station if you are not sure of the type of power supply being in use. Connect the projector with the peripheral equipment before turning the projector Cord does not match the AC outlet, contact your sales dealer. Projector side AC Outlet side For the U.S.A. and Canada For Continental Europe Ground
  • Sanyo PLC-XW15 | Owners Manual - Page 9
    ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to fine tune the position and the tilt. 3 To shorten the ADJUSTABLE FEET, lift the front of the projector and pull and undo the FEET LOCK LATCHES. The position and the keystone distortion of the image can be adjusted using the Menu Operation. (Refer
  • Sanyo PLC-XW15 | Owners Manual - Page 10
    , and it is not designed to protect the LCD projector from external forces. Do not transport the projector through a courier or transport services with this bag. The projector can be damaged. When handling the projector, do not drop or bump the projector, subject it to strong forces or put other
  • Sanyo PLC-XW15 | Owners Manual - Page 11
    with the Remote Control of this projector, connect the mouse port of your personal computer to this terminal. (Refer to P13.) COMPUTER INPUT TERMINAL Terminal : HDB15-PIN Connect the display output terminal of the computer to COMPUTER INPUT terminal of this projector with the VGA Cable (supplied
  • Sanyo PLC-XW15 | Owners Manual - Page 12
    ) Y-Pb/Cb-Pr/Cr S-VIDEO VIDEO S - VIDEO Y - Pb/Cb - Pr/Cr RESET AUDIO OUT AV COMPUTER IN COMPUTER AUDIO IN CONTROL PORT AV AUDIO IN Audio Cable (Stereo) ✽ Terminals of the Projector 12 Audio Input External Audio Equipment Audio Speaker (stereo) Audio Amplifier NOTE : When connecting the
  • Sanyo PLC-XW15 | Owners Manual - Page 13
    Audio Output Control Cable Control Cable Control Cable for Serial Port ✽ for PS/2 Port for ADB Port ✽ Terminal Terminal Terminal Audio Cable (stereo) ✽ VGA Cable Use one of these Control Cables corresponding with the terminal of your computer. Terminals of the Projector VIDEO S - VIDEO
  • Sanyo PLC-XW15 | Owners Manual - Page 14
    to pan the image in DIGITAL ZOOM mode. (P28) It is also used as a PC mouse in Wireless Mouse Operation. (P34) ✽ When pressing the center of this button, it works as the SELECT button. Operating Range Point the remote control toward the projector (the Remote Receiver) whenever pressing the buttons
  • Sanyo PLC-XW15 | Owners Manual - Page 15
    (P21) D.ZOOM BUTTON Used to select DIGITAL ZOOM mode and resize the image. (P28 Replace two batteries at the same time. q Do not use a new battery with a used battery. q Avoid contact with water or liquid. q Do not expose the Remote Control Unit to moisture, or heat. q Do not drop the remote control
  • Sanyo PLC-XW15 | Owners Manual - Page 16
    also used to expand the image in DIGITAL ZOOM mode. (P28) LAMP REPLACE INDICATOR This indicator turns to yellow when the life of the projection lamp draws to an end. (P36) LAMP INDICATOR This indicator is dim when the projector is turned on. And bright when the projector is in stand-by mode. 16
  • Sanyo PLC-XW15 | Owners Manual - Page 17
    and adjust this projector through the ONSCREEN MENU. Refer to the following pages to operate each adjustment in the ON-SCREEN MENU. 1 MOVING THE POINTER Move the pointer (see the NOTE below) by pressing POINT button(s) on the TOP CONTROL or the REMOTE CONTROL. WIRELESS REMOTE CONTROL POINT BUTTON
  • Sanyo PLC-XW15 | Owners Manual - Page 18
    the parameters to match with the input signal format. (Refer to P24, 25) SETTING MENU Used to adjust Volume, set the Display Menu and reset Lamp Replacement Monitor Timer. (Refer to P32, 33) LANGUAGE MENU Used to select the language used in the Menu. (Refer to P33) SYSTEM MENU Used to select
  • Sanyo PLC-XW15 | Owners Manual - Page 19
    for connecting that equipment.) 2 Connect the projector's AC Power Cord into a wall outlet. The LAMP indicator lights RED, and the READY indicator lights GREEN. 3 Press the power ON-OFF button on the Remote Control Unit or on the Top Control to ON. The LAMP indicator dims, and the Cooling Fans start
  • Sanyo PLC-XW15 | Owners Manual - Page 20
    . FOCUS RING KEYSTONE ADJUSTMENT If the picture has keystone distortion, correct image with KEYSTONE adjustment. 1 Press the KEYSTONE v/w button on the Remote Control Unit or select the Keystone on the SCREEN menu. (Refer to page 28, 30.) The message "Keystone" is displayed. Keystone 2 Correct
  • Sanyo PLC-XW15 | Owners Manual - Page 21
    function is cancelled when the FREEZE button is pressed again or any other function button is pressed. P-TIMER FUNCTION Press the P-TIMER button on the Remote Control unit. The timer display "00 : 00" appears on the screen and the timer starts to count the time (00 : 00 ~ 59 : 59). To stop the
  • Sanyo PLC-XW15 | Owners Manual - Page 22
    the Top Control or the COMPUTER button on the Remote Control Unit. MODE COMPUTER SPECIFICATION" on page 23). When selecting Computer, this projector automatically projector is set correctly. (Refer to TROUBLESHOOTING on page 37.) SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually
  • Sanyo PLC-XW15 | Owners Manual - Page 23
    COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with x 768 63.48 36.00 79.35 87.17 (Interlace) HDTV1035i HDTV1080i NOTE : Specifications are subject to change without notice. 45.00 33.75 33.75 60.00 60.00 (Interlace) 60.
  • Sanyo PLC-XW15 | Owners Manual - Page 24
    adjust several parameters to match with those special signal formats. This projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUSTMENT function cannot
  • Sanyo PLC-XW15 | Owners Manual - Page 25
    items. Clamp Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment. Display area Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of "H" or "V" to match the resolution of the
  • Sanyo PLC-XW15 | Owners Manual - Page 26
    PICTURE IMAGE MANUALLY 1 Press Adjust the number to match your PC image. White balance (Red / Green / Blue) Move the arrow to the color that you want to this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit
  • Sanyo PLC-XW15 | Owners Manual - Page 27
    position of the image. This item can be adjusted manually. (Refer to page 27.) 3 Move the arrow to "Go!" and press the SELECT button to start the Auto Image function. This adjustment can be executed by pressing AUTO IMAGE button on the Remote Control Unit. Starts the adjustment on the item set to
  • Sanyo PLC-XW15 | Owners Manual - Page 28
    . The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message "D. Zoom" is displayed. This projector also enters Digital Zoom mode by pressing the D.ZOOM v/w button on the Remote Control Unit. Refer to the following for operation. Expand function To expand the image size, press the D.ZOOM
  • Sanyo PLC-XW15 | Owners Manual - Page 29
    the VIDEO button on the Remote Control Unit. MENU OPERATION Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. MODE button COMPUTER VIDEO SELECTING VIDEO SOURCE This projector automatically detects the signal
  • Sanyo PLC-XW15 | Owners Manual - Page 30
    System is PAL-M or PAL-N, select the system manually. This box indicates the system being selected. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce the proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC
  • Sanyo PLC-XW15 | Owners Manual - Page 31
    to increase purple, and press POINT RIGHT button to increase green. (From 0 to 63.) White balance (Red / Green / Blue) Move the arrow to the color that you this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control
  • Sanyo PLC-XW15 | Owners Manual - Page 32
    the MUTE button on the remote control unit. (Refer to page 21) Press the POINT RIGHT / LEFT button to adjust the volume. Move the arrow to the item and then press the SELECT button. Closes the Setting Menu. Blue back When this function is "On," this projector will produce a blue image instead
  • Sanyo PLC-XW15 | Owners Manual - Page 33
    on when the input signal connected or the projector is operated with any button on the Top Control or the Remote Control. Lamp age The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function
  • Sanyo PLC-XW15 | Owners Manual - Page 34
    Port of the projector with the Control Cable for Serial Port. OPERATING WIRELESS MOUSE When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on the Wireless Remote Control Unit. POINT button Used to move the pointer
  • Sanyo PLC-XW15 | Owners Manual - Page 35
    and adversely affect the life of the projector. Clean the Air Filters Replace each Air Filter properly. Make sure that the Air Filters are fully inserted. CAUTION Do not operate the projector with the Air Filter removed. Dust may accumulate on the LCD authorized dealer or service station for proper
  • Sanyo PLC-XW15 | Owners Manual - Page 36
    not reset the LAMP REPLACEMENT MONITOR TIMER when the lamp is not replaced. LAMP ASSEMBLY ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. information to the dealer. q Model No. of your projector : PLC-XW15 q Replacement Lamp Type No. : POA-LMP31 (Service Parts No. 610
  • Sanyo PLC-XW15 | Owners Manual - Page 37
    APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13. 2. Check cable connection. Verify that
  • Sanyo PLC-XW15 | Owners Manual - Page 38
    . WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain the
  • Sanyo PLC-XW15 | Owners Manual - Page 39
    APPENDIX TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Multi-media Projector 7.44" x 2.93" x Manual AC Power Cord Remote Control Transmitter and Batteries VGA Cable Control Cable for PS/2 port Carry Bag Lens Cover q The specifications
  • Sanyo PLC-XW15 | Owners Manual - Page 40
    Printed in Japan Part No. 610 292 2936 (1AA6P1P2749-- MP6AA) SANYO Electric Co., Ltd
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Owner's Manual
PLC-XW15
Multimedia Projector
MODEL