Sanyo PLCXF60 Instruction Manual, PLC-XF60 Advanced Screen Manager
Sanyo PLCXF60 Manual
 |
View all Sanyo PLCXF60 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLCXF60 manual content summary:
- Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 1
& Blending ADVANCED SCREEN MANAGER Owner's Manual Caution for using this software When installing this software on a computer, make sure to read carefully [License Agreement] on the installation screen. We assume no responsibility for any computer or system troubles, data lost, data corruption or - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 2
, Windows 2000/XP are registered trademarks and product names of Microsoft Corporation in the U.S.A. and other countries. Each name of corporation or product in Owner's manual is a trademark or a registered trademark of its respective corporation. 2 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 3
. By editing images with this software, you can project images on the spherical or curved screen with minimum distortion. When using several projectors to project one image on a multiscreen, the Blending function adjust image levels of overlapped parts. These advanced functions enable you to use - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 4
■ Installation of the Warp & Blending Board Install Warp & Blending Board to INPUT-4 of a projector or INPUT-5 of a slot. For details about installation, see the owner's manual supplied with the projector. Some projectors have already equipped with Warp & Blending Board at the time of purchase. 4 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 5
Connect the SERIAL PORT IN terminal of Warp & Blending Board to the SERIAL terminal of the PC which is installed this software. When operating several projectors equipped with Warp & Blending Board, connect SERIAL PORT OUT terminal of Warp & Blending board to the SERIAL PORT IN terminal of the next - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 6
output the signal input from SERIAL PORT IN. When projecting Warp & Blending image with several projectors, connect SERIAL PORT OUT to the next projector. You can give the identified codes to each projector to control all of them individually. 6. Start up Advanced Screen Manager 1. First, turn on - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 7
English Operation Screen of Advanced Screen Manager and Function of Each Part 7. Operation Screen of Advanced Screen Manager and Functions of Each Part After starting up Advanced Screen Manager, you will get the screen below. With using this screen, you can edit an image and project an edited image - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 8
a name. Send (T) w The end of application(X) Convert the adjusted data to binary data and send it to Warp&Blending board of the projector. Terminate Advanced Screen Manager. Type (T) Selecting a type of editing. Menu Item The No. is Toolbar icon No. Function (Page) Spherical (S) e Edit to - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 9
Function (Page) Resolution setting (R) Set the input/output resolution. (p13) Communication setting (C) Set the communication configuration with the projector. (p13) Test pattern(P) Optical axis setting (L) View angle setting (O) Center angle display (T) Blending (B) Display the Test pattern - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 10
and Blending Board). ■ Resolution setting Set the editing software adjust to resolution of images and operation configuration of projectors. ■ Optical axis setting Set the position of the lamp optical axis on the screen. ■ View angle setting Set the view angle. STEP-2 Image editing Select the - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 11
, select "Open(O)" in the "Fle(F)" menu then send it. The date loaded into Warp & Blending Board stored there and remain even after turning off the projector. CAUTION : MAKE SURE TO SAVE THE DATA WHICH IS LOADED TO WARP & BLENDING BOARD TO EDIT. WITHOUT DATA SAVING, YOU CANNOT CORRECT OR CHANGE THE - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 12
Operating Procedure ■ Center angle display Display the projection angle from horizontal and vertical direction. Display the current center angle calculated by algorithm of spherical correction, horizontal or vertical curve. The display is to confirm the current figure as a rough standard. Therefore - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 13
] Select the projector's ID number to send the edited data. When operating several projectors connected via Daisy chain, set the projector's ID No. then start to operate. Set projector's ID No. from the setting menu of the projector. ( For details, refer to the owner's manual of the projector.) 13 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 14
STEP-1 Setting of the Operation Configuration ■ Optical axis setting Set the optical axis. Confirm the position of optical axis and set it by PIXCEL figure (Number of pixels). X figure : Set the horizontal position on the screen. (adjustable range is 0 - 1024) Y figure : Set the vertical position on - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 15
small, the distance between vertical lines of the right and left edge become shorter to show the irregular surface of the cylinder. CAUTION : WHEN THE PROJECTOR EQUIPPED WITH ZOOM FUNCTION, SET THE VIEW ANGLE EACH TIME. ✽How to calculate the view angle When projecting with no warp state (Select OFF - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 16
of any of 1.Spherical correction, 6. Grid [Transition] editing 2.Horizontal curve ,3.Vertical curve, 4. Keystone by cell unit 7. Blending Edit to project one screen with using several projectors, 16 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 17
over the size of the screen, the square grid will disappear. At this stage, you cannot edit each point nor send the data to the projector. Edit each corner point again to get the correct position then the grid will appear again and editing becomes possible. Clue to adjust: First, drag - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 18
grid screen is not correct, the grid lines in the square will disappear. You can confirm the editing with sending the edited data to the projector. (See p29 ■ Sending ) You cannot drag each of B, D, E, G point when editing each of them to get the curved line and further editing become impossible on - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 19
English STEP-2 Image Editing ■ Horizontal curve This editing is to project on the horizontally curved screen. Select"Horizontal curver" from either "Type(T)" in the menu or the toolbar. The grid screen for Horizontal curve appears. Edit the same way as spherical correction. See ■ Spherical - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 20
STEP-2 Image Editing ■ Vertical curve This editing is to project on the vertically curved screen. Select "Vertical curvet" from either "Type(T)" in the menu or the toolbar. The grid screen for Vertical curve appears. Edit the same way as spherical correction. See ■ Spherical correction for basic - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 21
English STEP-2 Image Editing ■ Keystone This editing is for projecting diagonally on the flat screen. Select "Keystoney" from either toolbar or Type(T) in the menu. The grid screen for keystone editing appears. Edit the image the same procedure as editing on the spherical screen. Click any of A, C, - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 22
STEP-2 Image Editing ■ Grid (New) This editing is to project on the slightly distorted screen. You can edit the details along with the projection screen. Select "Grid correctionu" from "Type(T)" in the menu bar or toolbar icon. The grid screen for Grid correction appears. Edit each cell with - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 23
English STEP-2 Image Editing ■ Grid [transition] correction When you need further detailed editing after making basic editing in spherical correction, vertical curve, horizontal curve and keystone, select this function. You can edit each cell individually by mouse drag. Select this function then - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 24
image levels of the overlapped parts of projected screens when projecting on one screen with using several projectors. 1. First, select the projectors to adjust. Input projector's ID No. in the STEP-1 ■ Communication setting. 2. Select "Blending setting (B)" from either toolbar or "Type(T)" in the - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 25
the screen, YB = Bottom offset of the screen XL = Left offset of the screen, XR= Right offset of the screen, 3.Send the data to the projector and confirm the settings. Repeat image editing with step1-3 for each projector and adjust the overlapped parts to get the natural image. 25 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 26
STEP-2 Image Editing 16 Step editing 1. Drag the lines or Xa, Xb, Ya, Yb on the editing screen and adjust the overlapped width of the images. Each line shows the following screen position. Xa = Left width of the screen, Xb = Right width of the screen, Ya = Top width of the screen ,Yb = Bottom width - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 27
- age from the screen edge. Xb Xa Projector 2 Projector 1 Xb Screen of projector 2 Overlapped part POINT % LEVEL 2 Xa Screen of projector 1 LEVEL 1 POINT % 100% 3.Send the data to the projector and confirm the settings. Repeat step1-3 for each projector and adjust the overlapped parts to get - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 28
STEP-2 Image Editing ■ Confirmation of edited image This function is to confirm the each of Spherical correction, Horizontal curve, Vertical curve, Keystone, Grid correction with projecting the outline of edited images. To use this function, monitor out of the pc installed this software should be - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 29
English STEP-3 Image transmission STEP-3 Data Sending 11. Data Sending ■ Sending Send the edited data to Warp&Blending Board of the projector. Select "Send(T)" from either "File(F)" in the menu or the toolbar icon to display the send dialog. Press "Start" button then the data will be - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 30
STEP-3 Image transmission ■ Center angle display Display the current center angle calculated by spherical correction or algorithm of horizontal and vertical curve. This dialog only show the current figure as a rough standard and you cannot change the figure. ■ Screen Position Adjustment Adjust the - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 31
English STEP-3 Image transmission ■ Warp ON/OFF This function is to select ON/OFF of Warp. Before operation, set the communication with STEP-1 ■ Communication setting dialog. When selecting ON, the edited data which was sent to Warp & Blending Board is projected. When selecting OFF, the original - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 32
STEP-3 Image transmission ■ Test pattern This function is to confirm the edited images. Select "Test pattern (P)" to display test pattern below which is based on the editing you have made. With watching this screen, confirm the editing such as screen distortion, linearity, screen position. Select " - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 33
33 - Sanyo PLCXF60 | Instruction Manual, PLC-XF60 Advanced Screen Manager - Page 34
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
Warp & Blending
ADVANCED SCREEN MANAGER
Owner's Manual
Caution for using this software
When installing this software on a computer, make sure to read carefully
[License Agreement] on the installation screen. We assume no responsibility for
any computer or system troubles, data lost, data corruption or malfunction of
equipments caused by the software or mishandling. We highly recommend to
store the important data in the recording medium to another disc.
✽
You may not copy the printed materials accompanying with the software.
✽
The contents of this manual might be changed without notice.
✽
The picture shape and screen display could be different from actual ones.
English
日本語