Sanyo PLCXP51 Instruction Manual, PLC-XP51

Sanyo PLCXP51 Manual

Get Sanyo PLCXP51 PDF manuals and user guides View all Sanyo PLCXP51 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLCXP51 manual content summary:

  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 1
    Multimedia Projector MODEL PLC-XP50/XP51 PLC-XP50L/XP51L (Lensless) Owner's Manual
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 2
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 3
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 4
    otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number Trade Name Responsible party Address Telephone No. : PLC-XP50/PLC-XP51/PLC-XP50L/PLC-XP51L : Sanyo : SANYO FISHER COMPANY : 21605 Plummer
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 5
    OF EACH PART OF PROJECTOR 7 MANUAL PC ADJUSTMENT 26 SETTING-UP PROJECTOR CONNECTING AC POWER CORD POSITIONING PROJECTOR ADJUSTABLE FEET 8 PICTURE PROJECTION LENS 43 21 LAMP REPLACEMENT 44 21 LAMP REPLACE COUNTER 45 21 TROUBLESHOOTING 46 21 INDICATORS AND PROJECTOR CONDITION 48
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 6
    cannot display image of over 1280 x 1024 dots. When resolution of your computer is over than 1280 x 1024, reset a computer output for lower resolution. N Multi-Scan System This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 7
    EACH PART OF PROJECTOR FRONT OF CABINET TOP CONTROLS AND INDICATORS PROJECTION LENS AIR INTAKE VENT LENS COVER SPEAKERS INFRARED LAMP COVER CARRYING HANDLE BOTTOM OF CABINET When attached the PJ-Net organizer (optional part) to the projector, remove the these parts. Refer to the owner's manual
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 8
    service station if you are not sure of type of power supply being in use. Connect a projector with a peripheral equipment before turning a projector . Projector side AC Outlet side For the U.S.A. and Canada For Continental Europe Ground For the U.K. To POWER CORD CONNECTOR on your projector. To
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 9
    NOTE: The figures below are only for Model PLC-XP50/PLC-XP51. Projection lens is not provided with Model PLC-XP50L/PLC-XP51L. G This projector is designed to project on a flat projection surface. G Projector can be focused from 4.6' (1.4m) ~ 47.3' (14.4m). G Refer to figure below to adjust
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 10
    . (Refer to P 21 and 37.) ADJUSTABLE FEET FEET LOCK LATCHES INSTALLING PROJECTOR IN PROPER POSITION Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard. 10˚ Do not tilt the projector more than 10 degrees above and below. 10˚ NO UPWARD Do not
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 11
    CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR G Do not drop or bump a projector, otherwise damages or malfunctions may result. G When carrying a projector, use a suitable carrying case. G Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 12
    (supplied). USB CONNECTOR (Series B) When controlling computer with Remote Control Unit of this projector, connect USB terminal of your personal computer to this terminal. (Refer to P13.) RESET BUTTON This projector uses a micro processor to control this unit, and occasionally, this micro processor
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 13
    up as either Computer input or Monitor output before using this terminal. (See page 23.) Terminals of a Projector INPUT 1 ANALOG IN/OUT DIGITAL(DVI-D) R/C JACK AUDIO 1 IN/OUT USB RESET CONTROL PORT AUDIO 2 G B R H/V V VIDEO/Y Cb/Pb Cr/Pr INPUT 2 VIDEO/Y Cb/Pb Cr/Pr R-AUDIO-L S-VIDEO
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 14
    CONNECTING TO VIDEO EQUIPMENT Cables used for connection (✽ = Cable is not supplied with this projector.) • Video Cable (RCA x 1 or RCA x 3) ✽ • BNC Cable ✽ INPUT 1 ANALOG IN/OUT DIGITAL(DVI-D) R/C JACK AUDIO 1 IN/OUT USB RESET CONTROL PORT AUDIO 2 G B R H/V V VIDEO/Y Cb/Pb Cr/Pr
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 15
    D.ZOOM FREEZE NO SHOW MUTE IMAGE VOLUME- SELECT VOLUME+ MENU KEYSTONE LASER P-TIMER INPUT 1 ZOOM COLOR.M INPUT 2 INPUT 3 FOCUS LENS NETWORK POWER ON-OFF BUTTON Used to turn projector on or off. (P20) AUTO PC ADJ. BUTTON Use to operate AUTO PC Adjustment function. (P25) IMAGE BUTTON Used to
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 16
    LASER P-TIMER INPUT 1 ZOOM COLOR.M INPUT 2 INPUT 3 FOCUS LENS NETWORK NO SHOW BUTTON Used to turn picture into black image. INPUT 1). (P23) Operating Range Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range instructions and local rules.
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 17
    in Power Management mode. (P39) LAMP INDICATOR Becomes dim when a projector is turned on. And bright when a projector is in stand-by mode. MENU P23, 24, 30) FOCUS BUTTON Used to adjust focus. (P21) LENS SHIFT BUTTON Used to select LENS SHIFT function. (P21) POINT (VOLUME + / - ) BUTTONS Used
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 18
    OPERATE ON-SCREEN MENU You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate . P-TIMERCOMPUTER 1 ZOOM COMPUTER 2 VIDEO SELECT BUTTON Used to select item. FOCUS LENS FLOW OF ON-SCREEN MENU OPERATION Display ON-SCREEN MENU MENU BAR MENU ICON 1
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 19
    SELECT MENU Used to select image level among Standard, Real and Image 1 ~ 4. (Refer to P28) SCREEN MENU Used to adjust size of image. [Normal / True / Wide / Digital zoom +/-] (Refer to P29) SETTING MENU Used to change settings of projector or reset Lamp Replace Counter. (Refer to P37-40) INPUT
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 20
    or on Remote Control Unit, and a message "Power off?" appears on a screen. 2 Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this "Cooling Down" period
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 21
    corrected by KEYSTONE adjustment. Message disappears after 4 seconds. LENS SHIFT ADJUSTMENT 1 Press LENS SHIFT button on Top Control or LENS SHIFT L/M button on Remote Control Unit. Message "Lens shift" is displayed. 2 Press POINT UP button or LENS SHIFT L button to move image up, press POINT DOWN
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 22
    BASIC OPERATION PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button. NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out image. To restore to normal, press
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 23
    by pressing INPUT button on Top Control. Select INPUT source by pressing INPUT 1, INPUT 2 or INPUT 3 button on Remote Control Unit. If projector cannot reproduce proper image, select correct input source through MENU OPERATION (see below). NOTE G Input 1 terminal is switchable and can be used as
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 24
    signal input from computer. Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 46.) PC SYSTEM MENU PC SYSTEM Menu icon Displays system being selected. Mode 1 User preset adjustment in MANUAL PC ADJUSTMENT. Adjustment data can be stored in the Mode
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 25
    Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in Adjustment function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 26, 27.) G Auto PC
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 26
    INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 27
    Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and clear and then press SELECT button. Other icons operates as follows. Reset Reset all adjust parameters on adjustment dialog box to previous figure. Quit
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 28
    UP/DOWN button to move a red frame pointer to level that you want to set and then press SELECT button. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P36). IMAGE SELECT
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 29
    cannot display any resolution higher than 1280 X 1024. If your computer's screen resolution is higher than 1280 X 1024, reset resolution to lower before connecting projector. G Image data in other than XGA (1024 x 768) is modified to fit screen size in initial mode. G Panning function may not
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 30
    VIDEO INPUT SELECTING INPUT SOURCE WHEN SELECT INPUT 2 (5 BNC INPUT JACKS ) When connecting to those equipment, select a type of Video INPUT MENU source in SOURCE SELECT Menu. 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 31
    Video signal, and adjusts itself to optimize its performance. When Video System is 1035i or 1080i, select system manually first. COMPONENT VIDEO SIGNAL FORMAT If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 32
    frame pointer to level that you want to set and then press SELECT button. IMAGE SELECT MENU IMAGE SELECT Menu icon Standard Normal picture level preset on this projector. Move red frame pointer to level and press SELECT button. Cinema Picture level adjusted for picture with fine tone. Level
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 33
    VIDEO INPUT PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display desirable image size. 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 34
    adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required. The projector lets you replace up to eight colors for each image. There are four preset images for VIDEO mode and four preset images for PC, giving
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 35
    palette. Gamma adjustment palette. COLOR SELECTION MODE CANCEL The mode will return to the pointer mode (even if you press the MENU key on the projector or the remote control). (You will need to reselect and re-adjust the color in this case.) QUIT The COLOR MANAGEMENT menu will be exited
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 36
    ···· Progressive scan mode to ON (for still picture). Store To store manually preset image, move a red frame pointer to Store icon and press SELECT set and then press SELECT button. Other icons operates as follows. Reset Reset all adjustment to previous figure. Quit Closes IMAGE MENU. Press SELECT
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 37
    frame pointer to item and press SELECT button. Lamp mode When selecting the Lamp mode, the projector reduce the brightness and set into the low adjustment data when disconnect AC Power Cord from an AC outlet. Reset ··· Reset the keystone adjustment data when disconnect AC Power Cord from an AC
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 38
    is "On," the screen image is forcibly changed to a 4:3 image, even if the input signal is HDTV. Blue back When this function is "On," this projector will produce a blue image instead of the video noise on the screen when any input source is unplugged or turned off. Display This function decides
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 39
    to the time setting, and then use the POINT LEFT/RIGHT button(s) to set the time (1 minute to 30 minutes). On start Time left until Lamp off. When this function is "On," projector is automatically turned on just by connecting AC Power cord to a wall outlet. Note ; Be sure to turn
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 40
    then while pressing a SELECT button, reinsert the AC cord, This will cancel the projector's control panel lock. Lamp counter reset This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 45 for operation
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 41
    your computer has no mouse port, connect Serial Port of your computer to Control Port of the projector with Control Cable for Serial Port (supplied). OPERATING WIRELESS MOUSE When controlling a PC mouse pointer, (right button of the mouse) P-TIMERCOMPUTER 1 ZOOM COMPUTER 2 VIDEO FOCUS LENS 41
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 42
    performing above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact the service station. When both of the Warning Temp. and Ready indicators are flashing: When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 43
    , or optical elements inside a projector. This condition may degrade quality of a projected image. When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING PROJECTION LENS Follow these steps to clean Projection Lens: 1 Apply a non-abrasive
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 44
    give the following information to the dealer. G Model No. of your projector : G Replacement Lamp Type No. : G Replacement Lamp Type No. : PLC-XP50/XP50L/XP51/XP51L POA-LMP67 (for PLC-XP50/XP50L) (Service Parts No. 610 306 5977) POA-LMP81 (for PLC-XP51/XP51L) (Service Parts No. 610 314 9127) 44
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 45
    a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion. G A Lamp may explode as a result of vibration
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 46
    APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check matters below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 ~ 14. 2. Check cable connection. Verify
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 47
    can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOTING" section on pages 46, 47. To correct failure, try "Solutions". If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or store where
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 48
    center for service and checkup. Do not leave the projector on. It may cause electric shock or a fire hazard. ✽ The projector is in the Power management mode. • • • on • • • flashing • • • dim • • • off ✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 49
    APPENDIX COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 180 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq.
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 50
    System 1) Mode 1 Mode 2 VGA 1 SVGA 1 XGA 1 Image Standard Real Image 1 Image 2 Image 3 Image 4 50 MENU TREE RGB RGB Horizontal Vertical Current mode Clamp Display area Display area H Display area V Full screen Reset Mode free Store Quit Video source 0 - 31 System 2) System 3) 640 x 480
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 51
    Remote control code USB Key lock Lamp counter reset Factory default Volume Built-in SP. Reset Store/Reset On/Off On/Off On/Off Image adjust Scale Position Scale Position On/Off On/Off On/Off Off/Ready/Shut down On/Off Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit Mouse Projector
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 52
    USB Cable Control Cable for Serial port Protective Dust Cover Lens Cover (PLC-XP50/XP51) Lens Attachment (PLC-XP50L/XP51L) G Specifications are subject to change without notice. G LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 53
    CONFIGURATIONS OF TERMINALS COMPUTER INPUT-1 and MONITOR OUT TERMINALS (ANALOG) Terminal : HDB15-PIN Pin Configuration 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 9 +5V Power 2 Green Input 10 Ground (Vert.sync.) 3 Blue Input 11 Sense 0 4 Sense 2 12 DDC Data 5 Ground (Horiz.sync.) 13
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 54
    may cause injury. To the sales and service engineer; Referring to the attached lens replacement and installation manual, replace or install the lens properly. After installing the lens, attach the lens cap to the lens when setting up the projector. Do not hold the lens when carrying or lifting the
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 55
    APPENDIX 55
  • Sanyo PLCXP51 | Instruction Manual, PLC-XP51 - Page 56
    Printed in Japan Part No. 610 315 6910 (1AA6P1P3972A- MH5A) SANYO Electric Co., Ltd
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Owner’s Manual
PLC-XP50/XP51
Multimedia Projector
MODEL
PLC-XP50L/XP51L
(Lensless)