Sanyo PLV-HD100 RS232C
Sanyo PLV-HD100 - 5500 Lumens Manual
 |
View all Sanyo PLV-HD100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLV-HD100 manual content summary:
- Sanyo PLV-HD100 | RS232C - Page 1
1.65"Full HD BASIC SERIAL COMMAND & EXPAND SERIAL COMMAND FUNCTIONAL SPECIFICATION PLV-HD10 Abridged Version Ver. Rev.A Page 1 / 18 - Sanyo PLV-HD100 | RS232C - Page 2
BASIC SERIAL COMMAND 1 Overview...3 2 Serial Interface Specification 3 2.1 Transfer Specification 3 3 Command ...3 4 Notes for Communication 3 5 Functional Execution Command Table 5 6 Format ...6 7 Transfer Example...6 8 Operation Requirements 6 9 Specifications for COMMAND with Address 8 9.1 - Sanyo PLV-HD100 | RS232C - Page 3
BASIC SERIAL COMMAND 1 Overview -This specification defines projector control commands for PLV-HD10. -The projector control commands are for remote controlling a projector through RS232C from a computer. -When using commands with address, see section 6. 2 Serial Interface Specification 2.1 - Sanyo PLV-HD100 | RS232C - Page 4
cases, the data in the receive buffer is cleared. ・ When Projector receives LF (0x0A) or EOF (0x1A9). ・ When it takes UP/DOWN], [FOCUS UP/DOWN], [LENS SHIF UP/DOWN/LEFT/RIGHT] command -> 7 seconds for intarnal initialization and lamp lighting process. During this period, used. Ver. Rev.A Page 4 / 18 - Sanyo PLV-HD100 | RS232C - Page 5
C0B AUDIO MUTE ON C0C AUDIO MUTE OFF C0D VIDEO MUTE ON C0E VIDEO MUTE OFF C0F Screen Normal size C10 Screen Full Lens Shift Up Lens Shift Down Lens Shift Left Command C60 C70 C71 C72 C89 Item Lens Shift Right Full Lamp Mode （4 Lamp） Half Lamp Mode （2 Lamp：1-4） Half Lamp Mode （2 Lamp - Sanyo PLV-HD100 | RS232C - Page 6
of those functions applys the same way of reception with remote control; -Assuming that the source system issues commands every 120 ms, the consecutive execution of the function is stopped. -When the projector receives the other command within 120ms, the continuous execution of the function is - Sanyo PLV-HD100 | RS232C - Page 7
process with Power Save NONE Power Save C00: POWER ON C01: POWER OFF Note) In the above status, even if the projector receives the other command, the projector returns [ACK] [CR]. INPUT 1 Command COMMAND "C05" [CR] Details Select Slot 1 input. Note) When there is no card inserted to Slot - Sanyo PLV-HD100 | RS232C - Page 8
with address are to remote control multiple projectors by one computer. -The Ex) Status Read Command "A001CR0" [CR] -Projector provides a function in the service mode, where its own address can be set. 999") When using "FFF" as the address, the command is processed by all projectors. Ver. Rev.A Page - Sanyo PLV-HD100 | RS232C - Page 9
strings（See Basic Command or Expand Command） -The only projectors for which the address assigned matches the one in the is required. The operation of those functions applys the same way of reception with remote control; -Assuming that the source system issues commands every 100ms. -When such - Sanyo PLV-HD100 | RS232C - Page 10
functions of the communication with Network card for PLV-HD10 (1.65" Full HD 4-Lamp model). -Support Projector Firmware Ver.1.x. -Commands are to communicate with Wireless Imager, but most commands can be used for remote controlling projectors through RS232C. Therefore commands are defined as Expand - Sanyo PLV-HD100 | RS232C - Page 11
not issue any commands. -Serial commands are invalid in the services mode or with the special menu displayed. 4． Notational Convention -Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller for the incoming command is represented as RESPONSE - Sanyo PLV-HD100 | RS232C - Page 12
- %%%: Error Code from a projector - "000": Normal Reception See "6. Error Code Table" for error numbers. 5． Functional Execution Command Table 5.1 Input Control Command Table Execution Command Item CF_INPUT_%1[CR] Select Input. - Sanyo PLV-HD100 | RS232C - Page 13
for some causes. See "Error Code Table" for the details -When the received data is failed to decode. "?" [CR] 7.2 Transfer Example When setting projector total dots command to 1344 by Expand Command PC --> PJ: "CF_TDOTS_1344" [CR] PC - Sanyo PLV-HD100 | RS232C - Page 14
projector body or remote control. Response Acceptable "000" [CR] Unacceptable "%%%" [CR] CF_SOURCE COMMAND Command "CF_SOURCE_%1" [CR] "DIGITAL Select DVI Digital input of computer "ANALOG Select Analog input of computer "VIDEO Select Composite Video input. "S-VIDEO Select S-Video - Sanyo PLV-HD100 | RS232C - Page 15
3 "4 Specify Input 4 "DIGITAL".......... Select Computer DVI Digital input "ANALOG""........ Select Computer Analog input "VIDEO Select Composite Video input "S-VIDEO"......... Select S-Video input "SCART Select SCART input %2 "HDCP Select HDCP input "YC Select Y/C input "YPBPR Select - Sanyo PLV-HD100 | RS232C - Page 16
"PAL Select PAL "SECAM Select SECAM "PAL-M Select PAL-M %1 "PAL-N Select PAL-N "1080I60 Select 1080i 60Hz "1080I60 Select 1080i 50Hz Video inputs "1035I Select 1035i "720P Select 720p "575P Select 575p "480P Select 480p "575I Select 575i "480I Select 480i "1080P30 Select - Sanyo PLV-HD100 | RS232C - Page 17
Address"CF_" COMMAND"_"Parameter [CR] Address: 3-digit number ("001" to "999") When using "FFF" as the address, the command is processed by all projectors. Command: strings (See Basic Command or Expand Command) -The only projectors for which the address assigned matches the one in the received data - Sanyo PLV-HD100 | RS232C - Page 18
execution; For some functions, the consecutive execution is required. The operation of those functions applys the same way of reception with remote control; -Assuming that the source system issues commands every 100ms. -When such commands are received, the corresponding funnction is executed
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
Ver.
Rev.A
Page
1 / 18
1.65”Full HD
BASIC SERIAL COMMAND
&
EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATION
PLV-HD10
Abridged Version