Sanyo SU22N Owners Manual

Sanyo SU22N - PLC SVGA LCD Projector Manual

Get Sanyo SU22N - PLC SVGA LCD Projector PDF manuals and user guides View all Sanyo SU22N manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo SU22N manual content summary:

  • Sanyo SU22N | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-SU22N Owner's Manual
  • Sanyo SU22N | Owners Manual - Page 2
    service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual. You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING
  • Sanyo SU22N | Owners Manual - Page 3
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo SU22N | Owners Manual - Page 4
    PROJECTOR 9 CONNECTING THE PROJECTOR 10 TERMINALS OF THE PROJECTOR 10 CONNECTING TO THE VIDEO EQUIPMENT 11 CONNECTING TO THE COMPUTER 12 BEFORE OPERATION 14 OPERATION OF THE REMOTE LAMP REPLACEMENT 43 LAMP REPLACEMENT MONITOR TIMER 43 TROUBLESHOOTING manual is a trademark or
  • Sanyo SU22N | Owners Manual - Page 5
    crystal display (LCD) technology. x Compatibility This projector is compatible with many different types of personal computers and video devices, including and the Owner's Manual for Media Card imager for operations. x Laser Pointer Function The Remote Control Unit of this projector has the Laser
  • Sanyo SU22N | Owners Manual - Page 6
    REMOTE RECEIVER BACK OF THE CABINET EXHAUST VENT HOT AIR EXHAUSTED ! Air blown from the exhaust vent is hot. When using or installing the projector, will become hot while the projector is used. POWER CORD CONNECTOR CARRY HANDLE SPEAKER (Monaural) INFRARED REMOTE RECEIVER BOTTOM OF THE CABINET
  • Sanyo SU22N | Owners Manual - Page 7
    FEET and rotate the ADJUSTABLE FEET for fine tune of the position and the tilt. 3 To shorten the ADJUSTABLE FEET, lift the front of the projector and pull and undo the FEET LOCK LATCHES. The position and the keystone distortion of the image can be also adjusted with the Menu Operation
  • Sanyo SU22N | Owners Manual - Page 8
    into any other type of power system. Consult your authorized dealer or service station if your are not sure of the type of power supply in use. Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 10 ~ 13 for connection.) CAUTION For safety, unplug
  • Sanyo SU22N | Owners Manual - Page 9
    q Do not drop or give a shock to the projector, otherwise damages or malfunctions may result. q When carrying the projector, use a carrying case recommended by Sanyo. q Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to
  • Sanyo SU22N | Owners Manual - Page 10
    VIDEO R-AUDIO-L(MONO) AUDIO VIDEO IN COMPUTER IN OUT MONITOR OUT CONTROL PORT VIDEO INPUT JACK Connect the video output from the video 13.) CONTROL PORT CONNECTOR When controlling the computer with the Remote Control of this projector, connect the mouse port of your personal computer to this
  • Sanyo SU22N | Owners Manual - Page 11
    supplied with this projector. Video / Audio Output S-VIDEO Output Video Audio Cable V S-VIDEO Cable V Use the either of VIDEO jack or S-VIDEO jack. When the both jacks are connected, the S-VIDEO jack has priority over the VIDEO jack. S-VIDEO Terminals of the Projector R-AUDIO-L(MONO) AUDIO
  • Sanyo SU22N | Owners Manual - Page 12
    FOR SERIAL PORT,or ADB PORT V • MAC ADAPTER V • MONITOR CABLE V • PC AUDIO CABLE (stereo) V V These cables are not supplied with this projector. IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA) Desktop type Laptop type Monitor Audio Speaker (stereo) Audio Amplifier To the
  • Sanyo SU22N | Owners Manual - Page 13
    CONNECTING THE PROJECTOR S-VIDEO R-AUDIO-L(MONO) AUDIO VIDEO IN COMPUTER IN OUT MONITOR OUT CONTROL PORT the table below depend- ON ing on the RESOLUTION MODE that you want to use before your turn on the projector and computer. OFF ON DIP 123456 1 23 4 56 13" MODE (640 x 480) ON ON OFF
  • Sanyo SU22N | Owners Manual - Page 14
    operation. (P17-19) COMPUTER/ MCI VIDEO ON-OFF ZOOM FOCUS VOLUME MUTE D.ZOOM PAGE MENU ALL-OFF SWITCH When using the Remote Control Unit, turn this switch to " SHOW FREEZE AUTO IMAGE NORMAL POWER ON-OFF BUTTON Used to turn the projector on or off. (P20) POINT BUTTON Used to move the pointer on
  • Sanyo SU22N | Owners Manual - Page 15
    Used to adjust zoom. (P21) COMPUTER/ MCI VIDEO ON-OFF ZOOM FOCUS VOLUME FOCUS BUTTON Used to adjust mode only. (P34) Operating Range Point the remote control toward the projector (Receiver Window) when pressing the buttons. Maximum operating range for the remote control is about 16.4' (5m) and 60
  • Sanyo SU22N | Owners Manual - Page 16
    projector temperature is too high. (P42) LAMP READY WARNING TEMP. LAMP REPLACE LAMP REPLACE INDICATOR This indicator turns to yellow when the life of the projection lamp . (P22) MODE BUTTON Used to select input source among Computer, Video or MCI. (P23, 30) SELECT BUTTON Used to execute the item
  • Sanyo SU22N | Owners Manual - Page 17
    OPERATE ON-SCREEN MENU You can control and adjust this projector through ONSCREEN MENU. Refer to the following pages to the NOTE below) by pressing POINT button(s) on the TOP CONTROL or the REMOTE CONTROL. WIRELESS REMOTE CONTROL POINT BUTTON Used to move the Pointer to UP/ DOWN/ RIGHT/ LEFT
  • Sanyo SU22N | Owners Manual - Page 18
    25) SETTING MENU Used to set the Display Menu and to reset Lamp Replacement Monitor Timer. (Refer to P40) AUTO IMAGE MENU Used to adjust (Refer to P40) MENU BAR IN VIDEO MODE Press MENU BUTTON while being in Video mode. MODE MENU Used to select the Video input. (Refer to P30) IMAGE MENU
  • Sanyo SU22N | Owners Manual - Page 19
    MENU BAR IN MCI MODE Press MENU BUTTON while being in MCI mode. MODE MENU Used to select the MCI input mode. (Refer to P33) IMAGE MENU Used to adjust the computer image. [Fine sync. / Total dots / White Balance / Contrast / Brightness] (Refer to P36) These icons have the same function as the
  • Sanyo SU22N | Owners Manual - Page 20
    projector's AC power cord into a wall outlet. The LAMP indicator lights RED, and the READY indicator lights GREEN. 3 Press the power ON-OFF button on the Remote Control Unit or on the Top Control to ON. The LAMP or service station. NOTE: The Cooling Fan may work for cooling while the projector is
  • Sanyo SU22N | Owners Manual - Page 21
    Digital Zoom operation. The message disappears after 4 seconds. FOCUS ADJUSTMENT 1 Press the FOCUS button on the Top Control or the FOCUS v/w button on the Remote Control Unit to turn into the FOCUS mode. 2 Adjust the focus of the image by pressing the POINT UP/DOWN button or the FOCUS v/w button
  • Sanyo SU22N | Owners Manual - Page 22
    again or any other function button is pressed. No show The message disappears after 4 seconds. PICTURE FREEZE FUNCTION Press the FREEZE button on the Remote Control Unit to turn the picture remained on-screen. This function is cancelled when the FREEZE button is pressed again or any other function
  • Sanyo SU22N | Owners Manual - Page 23
    / MCI button on the Remote Control Unit. MODE button COMPUTER MCI COMPUTER / MCI button COMPUTER MCI VIDEO MENU OPERATION Press the MENU and the projector is set correctly. (Refer to TROUBLESHOOTING on page 44.) SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually, select the
  • Sanyo SU22N | Owners Manual - Page 24
    , to enable you to precisely adjust several parameters to match with those exceptional signal formats and the projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. 1 Press the
  • Sanyo SU22N | Owners Manual - Page 25
    items. Clamp Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment. Display area Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of "H" or "V" to match the resolution of the
  • Sanyo SU22N | Owners Manual - Page 26
    COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 135 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION VGA 1
  • Sanyo SU22N | Owners Manual - Page 27
    COMPUTER MODE PICTURE IMAGE ADJUSTMENT ADJUST PICTURE IMAGE MANUALLY 1 Press the MENU button and the ON- picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Normal" display
  • Sanyo SU22N | Owners Manual - Page 28
    the image. This item can be adjusted manually. (Refer to page 28.) 3 Move the arrow to "Go!" and press the SELECT button to start the Auto Image function. This adjustment can be executed by pressing AUTO IMAGE button on the Top Control and the Remote Control Unit. Starts the adjustment on the
  • Sanyo SU22N | Owners Manual - Page 29
    . The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message "D. Zoom" is displayed. This projector is also turned into Digital Zoom mode by pressing the D.ZOOM v/w button on the Remote Control Unit. Refer to the following for operation. Expand function To expand the image size, press the
  • Sanyo SU22N | Owners Manual - Page 30
    system, and adjusts itself to optimize its performance. When the Video System is PAL-M or PAL-N, select the system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce the proper video image, it is required to select a specific broadcast signal format among PAL
  • Sanyo SU22N | Owners Manual - Page 31
    on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit ). The "Normal" display will be displayed on the screen for a few seconds. Normal VIDEO MODE It indicates the
  • Sanyo SU22N | Owners Manual - Page 32
    ) MC I Digital Camera PC Card (not supplied) SmartMedia with PC Card Adapter (supplied) PC CARD SLOT (Front) HOW TO LOAD THE MEMORY CARD INTO THE PROJECTOR LOAD Insert PC Card Adapter (with SmartMedia) or PC card into PC CARD SLOT. Make sure EJECT button pops out. NOTE : Be sure to insert
  • Sanyo SU22N | Owners Manual - Page 33
    is not available for this projector and cannot provide the image manually, operate as follows. DIRECT OPERATION Select MCI mode by pressing the MODE button on the Top Control or the COMPUTER / MCI button on the Remote Control Unit. MODE button COMPUTER MCI COMPUTER / MCI button COMPUTER MCI VIDEO
  • Sanyo SU22N | Owners Manual - Page 34
    another automatically.) To select Index or Page in the table, follow the instructions of INDEX SELECTION and PAGE SELECTION. Index and Page The data edited data edited by Media Card Imager has a priority to be projected with the LCD projector. The other image data in Bit Map type or JPEG type is not
  • Sanyo SU22N | Owners Manual - Page 35
    displayed. Operate Media Card Imager of your computer to write/read the data in the PC card. (Refer to Owner's Manual of Media Card Imager for operation.) NOTE : Connect the projector to the computer with Control Cable before turning those appliances on. Do not press any button while read/write the
  • Sanyo SU22N | Owners Manual - Page 36
    MCI MODE PICTURE IMAGE ADJUSTMENT ADJUST THE PICTURE IMAGE MANUALLY 1 Press the MENU button and the ON- picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Normal" display
  • Sanyo SU22N | Owners Manual - Page 37
    . The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message "D. Zoom" is displayed. This projector is also turned into Digital Zoom mode by pressing D.ZOOM v/w button on the Remote Control Unit. Refer to the following for operation. Expand function To expand the image size, press D.ZOOM
  • Sanyo SU22N | Owners Manual - Page 38
    MODE SMARTMEDIA AND PC CARD ADAPTER SmartMedia and PC Card Adapter are provided with this LCD projector. SmartMedia can be used as a PC card conforming to the PC Card Standard- AND THE DAMAGE OF A MEMORY CARD OR APPLIANCES. REFER TO OWNER'S MANUAL OF MEDIA CARD IMAGER FOR OPERATING THE SOFTWARE. 38
  • Sanyo SU22N | Owners Manual - Page 39
    MCI MODE PRECAUTIONS AND SPECIFICATIONS OF THE SMARTMEDIA q SmartMedia is a precision device. Do not bend it, drop it, subject it to strong forces or shocks or place where strong static electrical charge can be generated. q Do not touch the surface of the Contact Area with fingers or allow it to
  • Sanyo SU22N | Owners Manual - Page 40
    When this function is in the "On" position, this projector will produce a blue image instead of the video noise on the screen when all the input source is one. Lamp age The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement
  • Sanyo SU22N | Owners Manual - Page 41
    OPERATING WIRELESS MOUSE The Wireless Remote Control Unit is not only able to operate the projector but also usable as a mouse port, connect the Serial Port of the computer to Control Port of the projector with the Control Cable for Serial Port. OPERATING WIRELESS MOUSE When controlling the
  • Sanyo SU22N | Owners Manual - Page 42
    fully inserted. CAUTION Do not operate the projector with the Air Filter removed. The dust is stuck on the LCD Panel and the Mirror, and it may spoil the above symptoms are noticed, contact your authorized dealer or service station for the cleaning. CLEANING THE PROJECTION LENS Follow these steps
  • Sanyo SU22N | Owners Manual - Page 43
    REPLACEMENT MONITOR TIMER, when the lamp is not replaced. LAMP ASSEMBLY ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. information to the dealer. q Model No. of your projector : PLC-SU22N q Replacement Lamp Type No. : POA-LMP21J (Service Parts No. 610 280 6939) When
  • Sanyo SU22N | Owners Manual - Page 44
    APPENDIX TROUBLESHOOTING Before calling your dealer or service station for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment a s described in section "CONNECTING THE PROJECTOR" on pages 10 ~ 13. 2. Check cable connection. Verify that all
  • Sanyo SU22N | Owners Manual - Page 45
    Setting) is set properly. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. Sanyo Service is easily obtained. If after following all operating instructions, you find that service is necessary, contact the SFS Corporation in Los Angeles, or the store
  • Sanyo SU22N | Owners Manual - Page 46
    Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Projection Lens Throw Distance Projection Lamp 20nm) Owner's Manual AC Power Cord Remote Control Transmitter and
  • Sanyo SU22N | Owners Manual - Page 47
    OPTIONAL PARTS The parts listed below are optionally supplied. When ordering those parts, give the name and the Type No. of it to the sales dealer. q Control Cable for Serial Port Type No. : POA-MCSRL q Control Cable for ADB Port Type No. : POA-MCMAC q MAC Adapter Type No. : POA-MACAP 47
  • Sanyo SU22N | Owners Manual - Page 48
    SANYO INDUSTRIAL VIDEO LCD PROJECTOR LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from and Authorized Sanyo Factory Service Center at the user's expense, unless specifically stated otherwise in this warranty. the names and
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Owner's Manual
PLC-SU22N
Multimedia Projector
MODEL