Sanyo XU32 Instruction Manual, PLC-XU32

Sanyo XU32 - PLC XGA LCD Projector Manual

Get Sanyo XU32 - PLC XGA LCD Projector PDF manuals and user guides View all Sanyo XU32 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo XU32 manual content summary:

  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 1
    Multimedia Projector MODEL PLC-XU32 PLC-XU37 Owner's Manual
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 2
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "TROUBLESHOOTING" section at the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 3
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 4
    unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers Trade Name Responsible party Address Telephone No. : PLC-XU32, PLC-XU37 : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 5
    FLOW OF ON-SCREEN MENU OPERATION 17 APPENDIX 37 MENU BAR 18 LAMP REPLACEMENT 37 LAMP REPLACE 37 BASIC OPERATION 19 LAMP REPLACE COUNTER 38 OPERATING WIRELESS MOUSE 39 TURNING ON / OFF PROJECTOR 19 MAINTENANCE 40 ADJUSTING SCREEN ZOOM ADJUSTMENT FOCUS ADJUSTMENT 20 WARNING TEMP
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 6
    System This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 7
    Cooling Fans. LENS COVER INFRARED REMOTE RECEIVER POWER CORD CONNECTOR BOTTOM LAMP COVER ADJUSTABLE FEET AND FEET LOCK LATCHES SPEAKER TERMINALS AND CONNECTORS AIR FILTER AIR INTAKE VENTS (Back and Bottom) This projector is equipped with Cooling Fans for protection from overheating. Pay attention
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 8
    into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.) CAUTION For safety, unplug
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 9
    a flat projection surface. G The projector can be focused from 5.3'(1.6m) Lift the front of a projector and pull FEET LOCK LATCHES on the both sides of a projector. 2 Release FEET LOCK To retract ADJUSTABLE FEET, lift the front of a projector and pull and undo FEET LOCK LATCHES. Keystone distortion
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 10
    cabinet, and it is not designed to protect an appliance from external forces. Do not transport a projector through a courier or transport services with this bag. The projector can be damaged. When handling a projector, do not drop, bump, subject it to strong forces or put other things on the cabinet
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 11
    / WI MONITOR OUT USB CONTROL PORT AUDIO OUTPUT JACKS Connect an external audio amplifier to these jacks. (Refer to P12, 13.) RESET BUTTON This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 12
    (Not supplied) Set switches as shown in the table ON below depending on RESOLU- TION MODE that you want to use before you turn on projector and OFF computer. ON DIP 123456 1 2 3 4 56 13" MODE (640 x 480) ON ON OFF OFF OFF OFF 16" MODE (832 x 624) OFF ON OFF ON
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 13
    RESET MCI / WI MONITOR OUT USB CONTROL PORT AUDIO OUT AUDIO IN Terminals of the Projector Audio Cable (Stereo) ✽ NOTE : When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Audio Input External Audio Equipment
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 14
    1 minute, release LASER button and press it again. LASER KEYSTONE NO SHOW FREEZE AUTO PC ADJ. IMAGE P-TIMER POWER ON-OFF BUTTON Used to turn projector on or off. (P19) INPUT BUTTON Used to select input source. (P22, 30) POINT BUTTON Used to move a pointer on ON-SCREEN MENU, adjust each
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 15
    DIGITAL ZOOM +/- mode and resize image. (P29) Operating Range Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about of used batteries according to battery manufacturer's instructions and local rules. 15
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 16
    CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top. WARNING TEMP. INDICATOR Flashes red when internal projector temperature is too high. (P40) LAMP REPLACE INDICATOR Turns yellow when the life of the projection lamp draws to an end. (P37) MENU BUTTON Used to open or close MENU operation. (P17
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 17
    OPERATING ON-SCREEN MENU HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through ON-SCREEN MENU. Refer to the following pages to operate each adjustment on ON-SCREEN MENU. 1 DISPLAY MENU Press MENU button to display ON-
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 18
    Press MENU BUTTON while connecting to PC input source. GUIDE WINDOW Shows selected item of ONSCREEN MENU. PC SYSTEM Wide / Digital zoom +/-] (Refer to P29) SETTING MENU Used to change settings of projector or reset Lamp Replace Counter. (Refer to P35, 36) INPUT MENU Used to select input source
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 19
    projector. LAMP Indicator lights bright and READY Indicator turns off. After the projector projector has cooled down, READY Indicator lights GREEN again and you can turn the projector -OFF button to turn a projector off and disconnect AC Power .) 4. Turn the projector on again. If WARNING TEMP. Indicator
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 20
    BASIC OPERATION ADJUSTING SCREEN ZOOM ADJUSTMENT 1 Press ZOOM button on Top Control or ZOOM L/M button on Remote Control Unit. The message "Zoom" is displayed. 2 Press ZOOM L button or POINT UP button to make image larger, and press ZOOM M button or POINT DOWN button to make image smaller. Zoom
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 21
    BASIC OPERATION NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out the image. To restore to normal, press NO SHOW button again or press any other button. No show Message disappears after 4 seconds. P-TIMER FUNCTION Press P-TIMER button on Remote Control Unit. The timer
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 22
    from computer. Make sure the connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 41.) PC SYSTEM MENU SYSTEM Menu icon Displays system being selected. SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided in this
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 23
    COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION VGA 1
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 24
    . Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by Adjustment function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 25, 26.) G Auto PC
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 25
    reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 26
    SELECT button at Display area icon and Display area dialog box appears. Display area Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 27
    to move a red frame pointer to the level that you want to set and then press SELECT button. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. IMAGE SELECT MENU IMAGE SELECT Menu icon Move a red frame pointer to the level and press SELECT
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 28
    0 to 63.) Gamma Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.) 3 Store To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to the Image
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 29
    selected on PC SYSTEM Menu (P22). G True and Digital zoom +/- cannot be selected when "RGB" is selected on PC SYSTEM Menu (P22). G This projector cannot display any resolution higher than 1280 X 1024. If your computer's screen resolution is higher than 1280 X 1024, reset the resolution to the lower
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 30
    . Source Select Menu will appear. 3 Move a pointer to the source that you want to select and then press SELECT button. Auto Video Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance. • When both VIDEO jack and S-VIDEO jack are connected, S-VIDEO
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 31
    Video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 32
    Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture with fine tone. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P33, 34). IMAGE button
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 33
    VIDEO INPUT IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon. 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button. The
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 34
    icon Image Level Menu Move a red frame pointer to the image icon to be set and then press SELECT button. PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press MENU button and ON-SCREEN MENU will appear. Press
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 35
    distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s). Refer to KEYSTONE ADJUSTMENT on page 20. Blue back When this function is "On," this projector will produce a blue image instead of the video noise on the screen when any input source is unplugged or turned off. When pressing SELECT button
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 36
    and is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.) Power Management function operates to turn Projection Lamp off when the input signal is interrupted and any button is not pressed over 5 minutes
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 37
    SCREW HANDLE ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer. G Model No. of your projector : G Replacement Lamp Type No. : PLC-XU32 / PLC-XU37 POA-LMP35 (Service Parts No. 610 293
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 38
    a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion. G A Lamp may explode as a result of vibration
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 39
    Mouse may not work properly. Note : When your computer has no mouse port, connect Serial Port of your computer to Control Port of the projector with Control Cable for Serial Port (not supplied). OPERATING WIRELESS MOUSE When controlling a PC mouse pointer, operate Wireless Mouse with POINT button
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 40
    fully inserted. CAUTION Do not operate the projector with Air Filter removed. Dust may accumulate on LCD Panel and Projection Mirror degrading picture quality above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING PROJECTION LENS Follow these
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 41
    APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in the section "CONNECTING PROJECTOR" on pages 11 ~ 13. 2. Check cable connection.
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 42
    WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain the difficulty
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 43
    Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System High Definition TV Signal Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Projection Lens Throw Distance Projection Lamp ±20nm) Owner's Manual AC Power Cord
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 44
    APPENDIX CONFIGURATIONS OF TERMINALS MONITOR OUT TERMINAL (ANALOG) Terminal : HDB15-PIN Pin Configuration 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 9 +5V Power 2 Green Input 10 Ground (Vert.sync.) 3 Blue Input 11 Sense 0 4 Sense 2 12 DDC Data 5 Ground (Horiz.sync.) 13 Horiz. sync. 6
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 45
    CONTROL PORT CONNECTOR Terminal : Mini DIN 8-PIN Pin Configuration 876 5 43 21 PS/2 Serial ADB 1 ----- R X D ----- 2 CLK ----- ADB 3 DATA ----- ----- 4 GND GND GND 5 ----- RTS / CTS ----- 6 ----- T X D ----- 7 GND GND ----- 8 ----- GND GND USB CONNECTOR (Series B) Pin
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 46
    46
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 47
    47
  • Sanyo XU32 | Instruction Manual, PLC-XU32 - Page 48
    Printed in Japan Part No. 610 300 3955 (1AA6P1P3378-- MK8A) SANYO Electric Co., Ltd
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Multimedia Projector
MODEL
PLC-XU32
PLC-XU37
Owner’s Manual