Schwinn 130 Upright Bike 2007 model Assembly Manual
Schwinn 130 Upright Bike 2007 model Manual
View all Schwinn 130 Upright Bike 2007 model manuals
Add to My Manuals
Save this manual to your list of manuals |
Schwinn 130 Upright Bike 2007 model manual content summary:
- Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 1
Do not print this page - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 2
©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 3
Upright bike Assembly guide PN 001-6896 Rev B (031308) Assembly Guide - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 4
CONTENTS Table of Contents Hardware 2 Exploded View 2 Parts List 4 Assembly Instructions 5 Important Contact Numbers 17 1 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 5
Hardware Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.1270 2 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 6
EXPLODED VIEW EXPLODED VIEW - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 7
PARTS LIST PARTS LIST Ref. Description Qty A Computer 1 A-1 Screw M5x14L 4 A-2 Computer bracket 1 B Handlebar 1 B-4 Heartrate wire 1 C Handlebar mast 1 C-1 Upper computer wire 1 C-2 Bottle cage 1 C-3 Screw M5x20L 2 D Front stabilizer - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 8
gather the pieces you need for each step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes. 3. As a general rule, and for - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 9
ASSEMBLY INSTRUCTIONS Step 1 Install Front and Rear Stabilizers Parts: • Front Stabilizer (Ref. D ) • Rear Stabilizer (Ref. E ) Tools: • Supplied Allen Wrench 1-1 Attach the Rear Stabilizer (E) to the rear of - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 10
ASSEMBLY INSTRUCTIONS Step 2 Install Pedals Parts: • Right Pedal (K-R) • Right Pedal (K-L) Tools: • Supplied Pedal Wrench 2-1 Screw the Left Pedal ( has an "L" stamped into the end of the pedal ) - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 11
ASSEMBLY INSTRUCTIONS Step 3 Install Seat Post Parts: • Seat post (Ref. G) 3-1 Completely unscrew the Seat Post Adjustment Knob (F-7) from the main unit and insert the Seat Post (G) into the hole. Re-install the Adjustment Knob by screwing in firmly into place. G F-7 8 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 12
ASSEMBLY INSTRUCTIONS Step 4 Install Seat Parts: • Seat (Ref. G-8) Tools: • Supplied Wrench 4-1 Position the Seat (G-8) on the top of the Seat Slider. Tilt the the Seat to desired angle and tighten the two nuts on the underside of the Seat until completely tight. - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 13
ASSEMBLY INSTRUCTIONS Step 5 Install Handlebar Mast Parts: • Handlebar Mast (Ref C) Tools: • Supplied Allen Wrench 5-1 Remove the four Allen Bolts (F-4) and Curved Washers (F-1) from the frame . 5-2 Connect the - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 14
ASSEMBLY INSTRUCTIONS Step 6 Install Handlebar Parts: • Handlebar (Ref B) • Console Slider Adjust Knob (Ref 0-5) • Washer (Ref 0-6) • "T" Nut (Ref 0-8) 6-1 Tuck the Computer Wires into the Mast to allow insertion - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 15
ASSEMBLY INSTRUCTIONS Step 7 Install Computer Bracket Parts: • Computer Bracket (Ref. A-2) • Angle Adjust Knob (Ref. O) • Carriage Bolt (Ref. O-7) • Screw M8x85 (Ref. O-1) • 2 Washers (Ref. O-3) • Hex Nut (Ref. 0-2) Tools: • Supplied - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 16
ASSEMBLY INSTRUCTIONS Step 8 Install Computer Parts: • Computer (Ref. A ) Tools: • Supplied Phillips Head Screwdriver 8-1 Remove the four screws from the back of the Computer. 8-2 Connect the Computer Wire - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 17
ASSEMBLY INSTRUCTIONS Step 9 Install Bottle Cage Parts: • Bottle Cage (Ref. C-2 ) Tools: • Supplied Phillips Head Screwdriver 9-1 Remove the two M5 x 20L (Ref. C-3) screws from the Mast. 9-2 Align Bottle - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 18
ASSEMBLY INSTRUCTIONS Step 10 Plug in AC Adapter Parts: • AC Adapter (Ref. P) 10-1 Plug the AC Adapter (P) into the recepticle on the rear left of the unit and into a 110 volt outlet. P 15 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 19
ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner's Manual for information regarding computer operation, product maintenance, Warranty informa- tion, and general fitness and exercise guidelines. 16 - Schwinn 130 Upright Bike 2007 model | Assembly Manual - Page 20
CENTER Nautilus, Inc. 1886 Prairie Way Louisville, Colorado, USA 80027 Phone: 800-NAUTILUS (800-628-8458) Fax: 800-898-9410 • TECHNICAL/CUSTOMER SERVICE Nautilus, Inc. World Headquarters 16400 SE Nautilus Drive Vancouver, Washington, USA 98683 Phone: 800-NAUTILUS (800-628-8458) Fax: 877-686-6466
Do not print this page