Seagate ST320LT014 Momentus Thin (.2-4K) SATA Product Manual
Seagate ST320LT014 Manual
View all Seagate ST320LT014 manuals
Add to My Manuals
Save this manual to your list of manuals |
Seagate ST320LT014 manual content summary:
- Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 1
Product Manual Momentus® Thin 7200-RPM ST model # - Part # Standard models ST320LT007 - 9ZV142 ST250LT007 - 9ZV14C ST160LT007 - 9ZV14D Free-Fall Sensor models ST320LT011 - 9ZVG42 ST250LT011 - 9ZVG4C ST160LT011 - 9ZVG4D ST model # - - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 2
2011 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus and thus will not be available for data storage. Seagate reserves the right to change, without notice, product offerings or specifications. - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 3
Seagate Technology support services 1 2.0 Introduction 2 2.1 About the Serial ATA interface 3 3.0 Drive specifications 4 3.1 Specification 6.3 Supported ATA commands 26 6.3.1 Identify Device command 28 6.3.2 Set Features command 32 6.3.3 S.M.A.R.T. commands 33 Momentus Thin Product Manual, - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 4
ii Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 5
-2 models) - top, side and end view 20 Mounting dimensions (for standard models) - top, side and end view 21 Example of FIPS tamper evidence labels 22 Momentus Thin Product Manual, Gen-2 Rev. D iii - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 6
- Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 7
-us/support/warranty_&_returns_assistance For information regarding Data Recovery Services, visit http://www.i365.com For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system For Seagate reseller portal, visit http://spp.seagate.com Momentus Thin Product Manual - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 8
2.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus® Thin model drives: ST model # Part # Standard models ST320LT007 9ZV142 ST250LT007 9ZV14C ST160LT007 9ZV14D ST model # Part # Standard SED models ST320LT014 9YK142 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 9
is not normally necessary to set any jumpers or other configuration options. • support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive specification. The specification can be downloaded from http://www.serialata.org. Momentus Thin Product Manual, - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 10
specification measurement or definition, see the appropriate section of this manual Table 1: Drive specifications Drive specification transfer rate (Gb/s max) 3.0 ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.6 PIO modes 0-4 Multiword Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 11
specification, which may increase acoustic and power to operational levels. ***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes will not contribute to battery power consumption. Momentus Thin Product Manual - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 12
one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment 100-103) for additional information about 48bit addressing support of drives with capacities over 137GB. 3.3 Default logical geometry 1 6 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 13
to-track and average), are expected to meet the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications. Momentus Thin Product Manual, Gen-2 Rev. D 7 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 14
Idle, low power mode* Standby** Sleep +5V input average (25° C) 1.00A 1.6W 1.6W 1.9W 1.3W 0.90W 0.66W 0.15W 0.15W *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and 8 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 15
power to operational levels. **Standby power is measured at steady state (after 200ms from transition) Momentus Thin Product Manual, Gen-2 Rev. D 9 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 16
Deferred spinup Momentus Thin drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 3.9.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 10% 10 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 17
to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disk access is necessary. Momentus Thin Product Manual, Gen-2 Rev. D 11 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 18
3.10 Environmental specifications 3.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 10,000+ ft) -304.8 m to 12,192 m (-1000 ft to 40,000+ ft) 12 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 19
nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 5-500 Hz: 5.0 Gs (0 to peak). Max displacement may apply below 22Hz. Momentus Thin Product Manual, Gen-2 Rev. D 13 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 20
drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Test for Prominent Discrete Tones (PDTs) Seagate 250 cycles >95%, 0.5 cycles C EN 61000-4-11: 94 C B 14 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 21
. Drives are tested in a representative, end-user system by a Korean-recognized lab. • Certificate number: STX-MomentusThin (B) • Trade name or applicant: Seagate Technology LLC • Certificate date: May 14, 2010 • Manufacturer/nationality: USA, Singapore and China Momentus Thin Product Manual - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 22
Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. 16 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 23
MCV Standard. "X RoHS MCV 3.16 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial replacing materials near circuitry with sulfide-free alternatives. Momentus Thin Product Manual, Gen-2 Rev. D 17 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 24
, place a jumper on pins 1 and 2 to limit the drive to 1.5Gb/s operation. 3.0 Gbits per second operation Limit data transfer rate to 1.5 Gbits per second Jumper block SATA power connector SATA interface connector Figure 2. Serial ATA connectors 18 Momentus Thin Product Manual, Gen-2 Rev - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 25
excessive drive distortion when mounting. Refer to the following specifications for hard errors Non-operating with no hard errors 10 mm probe: 1.02kgf or 5 mm probe: 0.92kgf 20 mm probe: 2kgf at any point of top cover 20 mm probe: 15kgf at top cover edges only Momentus Thin Product Manual - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 26
Evident Stickers with the marking "Tamper Indicator - Do Not Remove". These stickers must remain attached to provide the tamper evidence throughout the life of the drive. Removing these stickers will indicate tampering and void the drive warranty. 20 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 27
Figure 5. Mounting dimensions (for standard models) - top, side and end view Momentus Thin Product Manual, Gen-2 Rev. D 21 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 28
Federal Information Processing Standard (FIPS) 140-2 Level 2 Certification requires drives to go through government agencies certifications to add requirements for physical tamper physical access. Figure 6. Example of FIPS tamper evidence labels. 22 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 29
Note. May not represent actual drive. Momentus Thin Product Manual, Gen-2 Rev. D 23 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 30
The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification. 6.1 Hot-Plug compatibility Momentus Thin drives incorporate - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 31
. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. 4. All used voltage pins (Vx) must be terminated. Momentus Thin Product Manual, Gen-2 Rev. D 25 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 32
by the value placed in the Set Max Fea- Password: 01H tures register as defined to the right. Lock: 02H Unlock: 03H Freeze Lock: 04H Set Multiple Mode C6h S.M.A.R.T. Disable Operations B0h/D9h S.M.A.R.T. Enable/Disable Autosave B0h/D2h 26 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 33
E1h Sleep E6h Standby E2h Standby Immediate E0h ATA-standard security commands Security Set Password F1h Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Momentus Thin Product Manual, Gen-2 Rev. D 27 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 34
set to zero. Parameters listed with an "x" are drive-specific or vary with the state of the drive. The following commands contain drive-specific features that may not be included in the Serial ATA specification 0000H 2F00H 0000H 0200H 0200H 0007H xxxxH 28 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 35
number Command sets supported Command sets supported Command sets support extension Command sets enabled Command sets enabled Command sets enable extension Ultra DMA support and current mode 003EH 0028H 306BH 4001H 4000H 30xxH 0001H 4000H xx7FH 0000H Momentus Thin Product Manual, Gen-2 Rev. D 29 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 36
Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. 30 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 37
supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported 6 Ultra DMA mode 6 is supported cable detected, CBLID below VIL Momentus Thin Product Manual, Gen-2 Rev. D 31 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 38
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY default values of the features are as indicated above. 32 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 39
Log Sector Vendor-specific S.M.A.R.T. Enable Operations S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register. Momentus Thin Product Manual, Gen-2 Rev - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 40
34 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 41
26 ATA data-transfer modes supported 4 Australia/New Zealand Standard RF immunity 14 Configuring the drive 18 connectors 19 CSA60950-1 Device Configuration Set 26 Diagnostics protection 17 Environmental specifications 12 error-correction algorithms Momentus Thin Product Manual, Gen-2 Rev. D 35 - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 42
12 Microcode 26 mounting 19 mounting screws 13 mounting the drive 18 36 N National Institute of Standards and Technology 22 dissipation 8 power management 11 power on/off cycles 15 Power specifications 8 Power-management modes 11 Power-on to Ready 8 Power- Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 43
Warranty 15 Weight 4 weight 7 Wet bulb temperature 5, 12 Width 4 width 7 Write Buffer 27 Write DMA 27 Write DMA Extended 27 Write Long with Retries 27 Write Long without Retries 27 Write Multiple 27 Write Sectors 27 Write Sectors Extended 27 write uncorrectable 27 Momentus Thin Product Manual, Gen - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 44
38 Momentus Thin Product Manual, Gen-2 Rev. D - Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 45
- Seagate ST320LT014 | Momentus Thin (.2-4K) SATA Product Manual - Page 46
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100625253, Rev. D
Product Manual
Momentus
®
Thin
7200-RPM
Gen-2
100625253
Rev. D
March 2011
ST model # - Part #
Standard models
ST320LT007 - 9ZV142
ST250LT007 - 9ZV14C
ST160LT007 - 9ZV14D
Free-Fall Sensor models
ST320LT011 - 9ZVG42
ST250LT011 - 9ZVG4C
ST160LT011 - 9ZVG4D
ST model # - Part #
SED model
ST320LT014 - 9YK142
ST250LT014 - 9YK14C
ST160LT014 - 9YK14D
SED (FIPS 140-2) models
ST320LT009 - 9WC142
ST250LT009 - 9WC14C
ST160LT009 - 9WC14D