Seagate ST9900805SS Savvio 10K.3 SAS Product Manual

Seagate ST9900805SS Manual

Get Seagate ST9900805SS PDF manuals and user guides View all Seagate ST9900805SS manuals
Add to My Manuals
Save this manual to your list of manuals

Seagate ST9900805SS manual content summary:

  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 1
    Product Manual Savvio® 10K.3 SAS Standard Models ST9300603SS ST9146803SS Self-Encrypting Drive Models ST9300503SS ST9146703SS SED FIPS 140-2 Models ST9300403SS ST9146603SS 100516229 Rev. H December 2011
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 2
    © 2011 Seagate Technology LLC. All rights reserved. Publication number: 100516229, Rev. H December 2011 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Savvio and SeaTools are either trademarks or
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 3
    Contents 1.0 Seagate Technology support services 1 2.0 Scope 2 3.0 Applicable standards and Preventive maintenance 15 6.2.3 Hot plugging the drive 15 6.2.4 S.M.A.R.T 16 6.2.5 Thermal monitor 17 6.2.6 Drive Self Test (DST 18 6.2.7 Product warranty 30 Savvio 10K.3 SAS Product Manual, Rev. H i
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 4
    download 40 9.8 Power requirements 40 9.9 Supported commands 40 10.0 Defect and error management 41 10.1 Drive internal defects/errors 41 10.2 Drive error recovery procedures 41 10.3 SAS system 12.4.7 Power 63 12.5 Signal characteristics 63 ii Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 5
    12.5.1 Ready LED Out 63 12.5.2 Differential signals 64 12.6 SAS-2 Specification compliance 64 12.7 Additional information 64 Savvio 10K.3 SAS Product Manual, Rev. H iii
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 6
    iv Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 7
    flow 46 Physical interface 59 SAS device plug dimensions 60 SAS device plug dimensions (detail 61 SAS transmitters and receivers 63 Savvio 10K.3 SAS Product Manual, Rev. H v
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 8
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 9
    support services SEAGATE ONLINE SUPPORT and SERVICES For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: Presales & Technical support Global Support Services telephone numbers & business hours Authorized Service
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 10
    SCSI) disk drives. Savvio drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part support services group as shown in Section 1.0. Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 11
    Section 11.3. 3.1 Standards The Savvio family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate SAS Interface Manual, part number 100293071. The drives are recognized in accordance with UL 60950-1 and CSA 60950-1 as tested by UL and EN60950-1 as
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 12
    the Electromagnetic Compatibility (EMC) Framework requirements of Australia's Spectrum Management Agency (SMA). Korean MIC If these drives have the Korean Communications Commission (KCC) logo, they comply of Standards, Metrology, and Inspection (BSMI). 4 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 13
    content declarations for all parts and materials for the disk drives documented in this publication. Current supplier declarations include disclosure Class Enterprise Specification, Rev. 1.0 Self-Encrypting Drives Reference Manual Seagate part number: 100515636 Specification for Acoustic Test
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 14
    support the Serial Attached SCSI Protocol as described in the ANSI specifications, this document, and the SAS Interface Manual (part number 100293071) which describes the general interface characteristics of this drive. Savvio drives with either SAS or SATA hard disk drives. This allows you to
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 15
    drives have the following standard features: • 1.5 / 3 / 6 Gbit Serial Attached SCSI (SAS) interface • Integrated dual port SAS controller supporting the SCSI protocol • Support task set (queue) • Supports up to 32 initiators • power is applied to the drive • Zone bit recording (ZBR the drive has
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 16
    Average latency = 3.0 msec • Background processing of queue • Supports start and stop commands (spindle stops spinning) • Adaptive seek list table in the SAS Interface Manual, part number 100293071. A value of zero in the Number of Blocks field indicates that the drive will not change the capacity
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 17
    sparing scheme and sector size requested. • Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection against transit number 75789512, is usually included with each standard OEM drive shipped, but extra copies may be ordered. Savvio 10K.3 SAS Product
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 18
    drive characteristics Drive capacity Read/write data heads Bytes per track Bytes per surface Tracks per surface (total) Tracks per inch Peak bits per inch Areal density Internal data rate Disk interface" on page 59 and the SAS Interface Manual (part number 100293071) for additional timing details.
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 19
    performance characteristics Minimum sector interleave Data buffer to/from disk media (one 512-byte logical block)* Sustained transfer stop time The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied. If the drive receives a NOTIFY
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 20
    Mode Page 02h (disconnect/reconnect control) in the SAS Interface Manual. The following is a simplified description of the prefetch/cache operation is not in any segment of the cache: 1. The drive fetches the requested logical blocks from the disk and transfers them into a segment, and then from
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 21
    drive does not overwrite data drive drive drive. 5.5.2 Prefetch operation If the Prefetch feature is enabled, data in contiguous logical blocks on the disk . The drive does not drive enables prefetch of contiguous blocks from the disk when it senses that a prefetch hit will likely occur. The drive
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 22
    The error rates stated in this manual assume the following: • The drive is operated in accordance with this manual using DC power as defined in as a failure of the drive to recover data from the media. These errors occur due to head/media or write problems. Unrecoverable data errors are only
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 23
    classified as drive failures. service You can enhance the reliability of Savvio disk drives by ensuring that the drive drive When a disk is powered on by switching the power or hot plugged, the drive drive looses sync, the drive initiated link reset. The drive test fails, the drive does not respond to
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 24
    every two hours subject to an idle period on the drive interfaces. The process of measuring off-line attribute data and saving data to the disk is uninterruptable. The maximum on-line only processing delay is is referred to as the Interval Counter. 16 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 25
    01-0B01 when the temperature exceeds the specified limit in compliance with the SCSI standard. The drive temperature is reported in the FRU code field of mode sense data. You can use this information Description Primary Temperature Reference Temperature Savvio 10K.3 SAS Product Manual, Rev. H 17
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 26
    drive fails the test, remove it from service and return it to Seagate for service. 6.2.6.1 DST failure definition The drive • Servo will not lock on track • Drive cannot read configuration tables from the disk In these conditions, the drive responds to a Test Unit Ready command with Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 27
    The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within 120 seconds. The short test does not scan the entire media surface, but does some self-test routine was interrupted by a reset condition). Savvio 10K.3 SAS Product Manual, Rev. H 19
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 28
    remaining warranty for a particular drive can be determined by calling Seagate Customer Service at 1-800-468-3472 label. Shipping a drive in a non-approved container voids the drive warranty. Seagate repair customer service centers are the only facilities authorized to service Seagate drives. Seagate
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 29
    of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply. Savvio 10K.3 SAS Product Manual, Rev
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 30
    Table 2: 300GB standard drive DC power requirements Voltage Regulation Avg idle current DC Maximum starting current (peak DC) DC (peak AC) AC Delayed motor 0.57 0.28 1.10 1.14 0.90 0.15 0.94 0.15 1.20 0.30 0.84 0.15 0.87 0.15 1.08 0.32 22 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 31
    supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient. after the drive signifies that its power-up sequence has been completed and that the drive is able completes but before the drive has received the Notify reads. [7] During idle, the drive heads are relocated every 60
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 32
    multiple drives from a common supply, careful consideration for individual drive power given below are peak-to-peak measurements and apply at the drive power connector. +5v = 250 mV pp from 100 Hz The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 33
    7.2.3 Current profiles The +12V and +5V current profiles for the Savvio 10k.3 drives are shown below. Figure 17. Current profiles for 300GB models Savvio 10K.3 SAS Product Manual, Rev. H 25
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 34
    Figure 18. Current profiles for 146GB models Note: All times and currents are typical. See Tables 2 and 3 for maximum current requirements. 26 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 35
    , refer to the following I/O rate curve (see Figure 19). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and and power vs. input/output operations per second Savvio 10K.3 SAS Product Manual, Rev. H 27
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 36
    operations, refer to the following I/O rate curve (see Figure 19). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and power vs. input/output operations per second 28 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 37
    operations, refer to the following I/O rate curve (see Figure 19). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and power vs. input/output operations per second Savvio 10K.3 SAS Product Manual, Rev. H 29
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 38
    typical I/O rate for a drive in your system on the drive must be such that condensation does not occur on any drive drive meets all specifications over a 41°F to 131°F (5°C to 55°C) drive drive drives ability to meet specifications. The MTBF specification for the drive to drive ambient the drive in
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 39
    drive is packaged in the shipping container designed by Seagate for use with drive that no condensation on the drive occurs. a. Operating 5% to on the drive chassis. If the drive is installed drive movement. The limits of shock and vibration defined within this document are specified with the drive
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 40
    drive both isolated drives and integrated drives. The drive subjected to applied in the X, Y, or Z axis. d. Packaged Disk drives shipped as loose load (not palletized) general freight will 1219 mm) 42 in (1067 mm) 36 in (914 mm) Drives packaged in single or multipacks with a gross weight of 20 pounds
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 41
    Y X X Z Y Figure 24. Recommended mounting 7.4.4.2 Vibration a. Operating-normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to random flat profile 10 - 500 Hz 1.2 GRMS Savvio 10K.3 SAS Product Manual, Rev. H 33
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 42
    includes both isolated drives and integrated drives. The drive shall not incur GRMS 7.4.5 Air cleanliness The drive is designed to operate in electronic drive as electronic drive component dB above the masking noise on typical drives when measured according to Seagate specification 30553-001
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 43
    7.5 Mechanical specifications Refer to Figure 25 for detailed mounting configuration dimensions. See Section 11.3, "Drive mounting." Weight: 0.50 pounds 0.227 kilograms Note. These dimensions conform to the Small Form Factor Standard documented in SFF-8201 and SFF-8223, found at
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 44
    module compliance/conformance testing. Seagate Enterprise SED The SED drives referenced in this Product Manual have been validated by CMVP and have been thoroughly of an operator to assume a specific role and perform a corresponding set of services. 36 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 45
    Figure 26. Example of FIPS tamper evidence labels. Note. Image is for reference only, may not represent actual drive. Savvio 10K.3 SAS Product Manual, Rev. H 37
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 46
    features in the drive, the host must drive in their command payloads. 9.1 Data encryption Encrypting drives is generated by the drive, never leaves the drive, and is inaccessible to gatekeepers to the drive security services. Security-related drive owner can define up to 16 data bands on the drive,
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 47
    drive label and it can be read by the host electronically over the I/O. After receipt of the drive RNG) The drive has a drive's Admin and Locking SPs. 9.4 Drive drive is removed from its cabinet. The drive the drive is own drive-generated encryption drive Since the drive overwrites the drive drive
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 48
    SED drive, the download file must pass the acceptance criteria for the drive. For example it must be applicable to the correct drive model (non-SED) drive models. 9.9 Supported commands The SED models support the following two commands in addition to the commands supported by the standard
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 49
    mode page. Error recovery and defect management may involve using several SCSI commands described in the SAS Interface Manual. The drive implements selectable error recovery time limits required in video applications. The error recovery scheme supported by the drive provides a way to control the
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 50
    a single reread or re-write attempt. The maximum level used by the drive in LBA recovery is determined by the read and write retry counts. Table drive. Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a role in systems error management
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 51
    drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into service by the host system. On regular duty drives to certify that the data was properly written to the disk. Note. During Pre-Scan write verify commands, write performance Manual, Rev. H 43
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 52
    recently written data from the media and compares it to valid write command data resident in the drives data buffer. Any sectors that fail the comparison result in the invocation of a rewrite and rewrite fails, the sector is re-mapped to a spare location. 44 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 53
    exceed 4 meters (13.1 feet). Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system's SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 12.4.1 for
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 54
    "Temperature." The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disk assembly (HDA). You should confirm that adequate heat removal is to side) Figure 28. Air flow Above unit Under unit 46 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 55
    you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to in the drive and cannot be separated by the user. The equipment in which the drive is mounted is electrically isolating) method of mounting the drive in the host equipment. Increased
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 56
    the SAS Interface Manual (part number 100293071). 12.1 SAS features This section lists the SAS-specific features supported by Savvio drives. 12.1.1 task management functions Table 5 lists the SAS task management functions supported. Table 5: SAS task management functions supported Task name
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 57
    support: • Concurrent port transfers-The drive supports receiving COMMAND, TASK management transfers on both ports at the same time. • Full duplex-The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving frames on both ports. Savvio 10K.3 SAS Product Manual, Rev. H 49
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 58
    7 lists the SCSI commands supported by Savvio drives. Table 7: Supported commands Command name Change Definition Compare Copy Copy and Verify Format Unit [1] DPRY bit supported DCRT bit supported STPF bit supported IP bit supported DSP bit supported IMMED bit supported VS (vendor specific) Inquiry
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 59
    ) Power Condition page (1Ah) Rigid Disk Drive Geometry page (04h) Unit Attention page supported FUA bit supported Read (12) A8h Read (16) 88h Read (32) 7Fh/0009h Supported N N Y Y Y N Y N Y Y Y Y [2] Y Y [2] Y Y Y Y Y Y Y N Y Y Y Y Y N Y Y Y N Y Y Y Y N N N Savvio 10K.3 SAS Product Manual
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 60
    Reassign Blocks Receive Diagnostic Results Supported Diagnostics pages (00h) Translate 10) Send Diagnostics Supported Diagnostics pages (00h 16h 56h 01h 31h 30h 32h A2h B5h 0Bh 2Bh 1Dh 33h 1Bh 35h 91h Supported Y (non-SED drives only) Y N Y Y Y (non-SED drives only) N Y Y Y Y Y Y Y Y Y Y Y Y Y
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 61
    can result in firmware corruption. This usually makes the drive inoperable. [3] Reference Mode Sense command 1Ah for mode pages supported. [4] Y = Yes. Command is supported. N = No. Command is not supported. A = Support is available on special request. Savvio 10K.3 SAS Product Manual, Rev. H 53
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 62
    drive should return to the initiator per the format given in the SAS Interface Manual ** SCSI Revision support. See the appropriate drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 63
    are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message. 4. Changeable values Changeable values the drive in response to the Mode Sense command pages for SCSI implementation (see the SAS Interface Manual ). DEF = Default value. Standard OEM drives
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 64
    Table 9: Mode Sense data for 300GB drives MODE DATA HEADER: 01 6e 00 10 00 00 00 08 BLOCK DESCRIPTOR: 22 ec b2 5c 00 00 02 00 MODE PAGES: DEF 81 ff ff DEF 80 06 00 80 0f 00 00 00 CHG 80 06 b7 c0 8f 00 00 00 56 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 65
    Table 10: Mode Sense values for 146GB drives MODE DATA HEADER: 01 6e 00 10 00 00 00 08 BLOCK DESCRIPTOR: 11 17 73 30 00 00 02 00 MODE PAGES: DEF 81 ff ff ff DEF 80 06 00 80 0f 00 00 00 CHG 80 06 b7 c0 8f 00 00 00 Savvio 10K.3 SAS Product Manual, Rev. H 57
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 66
    support column indicates the feature or condition is supported. An "N" in the support column indicates the feature or condition is not supported. Table 11: Miscellaneous features Supported queue tags supported) Deferred error offset bytes Table 12: Miscellaneous status Supported Y Y Y Y Y Y Y
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 67
    the dimensions of the SAS connector. Details of the physical, electrical, and logical characteristics are provided within this section. The operational aspects of Seagate's SAS drives are provided in the SAS Interface Manual. Figure 29. Physical interface Savvio 10K.3 SAS Product
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 68
    ) 5.08 B 0.84 0.05 (22X) 0.15 B 4.90 0.08 P15 P1 S1 S7 CL OF DATUM B Figure 30. SAS device plug dimensions 60 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 69
    A 0.03 1.23 0.05 65 30 0.08 0.05 Detail 2 1.90 0.08 2.40 0.08 0.10 A D Figure 31. SAS device plug dimensions (detail) SECTION B - B Savvio 10K.3 SAS Product Manual, Rev. H 61
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 70
    Ground Diff. input pair Diff output pair Diff. input pair Diff output pair * - Short pin to support hot plugging NC - No connection in the drive. Pin P1* P2* P3 P4 P5 P6 P7 P8* P9* P10 P11* P12 P13 P14* P15 Volts 12 Volts Signal type Open collector out 62 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 71
    and signal name information. 12.5.1 Ready LED Out The Ready LED Out signal is driven by the drive as indicated in Table 14. Table 14: Ready LED Out conditions Normal command activity Ready LED Meaning bit on and off for 0.5 seconds) Toggles on/off Savvio 10K.3 SAS Product Manual, Rev. H 63
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 72
    100 µA 0 ≤VOL ≤0.225 V 12.5.2 Differential signals The drive SAS differential signals comply with the intra-enclosure (internal connector) Manual, part number 100293071. For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 73
    surface 10 bytes per track 10 Savvio 10K.3 SAS Product Manual, Rev. H C cache operation 12 cache segments 12 48 clear task set function 48 commands supported 50 condensation 31 condition met/good service 20 D DAR 43 Data Bands 39 data bands 38 data block size modifing the 8 data buffer to/from disk
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 74
    34 EraseMaster 39 error management 41 rates 14 disk assembly. See HDA heads read/write data 10 heat removal 46 heat source 46 host equipment 47 hot plugging the drive 15 humidity 31 humidity limits 30 I Idle Read After Write 44 inquiry data 54 installation 45 guide 5 interface commands supported
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 75
    in Mode Select command 58 Synchronized (locked) spindle operation 58 Zero latency read 58 miscellaneous status support ACA active 58 ACA active, faulted initiator 58 Busy 58 Check condition 58 Condition met/good 58 14 recovered media data 14 reference Savvio 10K.3 SAS Product Manual, Rev. H 67
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 76
    self-encrypting drives 38 Self-Monitoring Analysis and Reporting Technology 8, 16 Serial Attached SCSI (SAS) Interface Manual 2 shielding management response codes 48 Function complete 00 48 Function not supported 05 48 Function reject 04 48 task set full status 58 TCG 38 technical support services
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 77
    Z zero latency read 58 zone bit recording (ZBR) 7 Savvio 10K.3 SAS Product Manual, Rev. H 69
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 78
    70 Savvio 10K.3 SAS Product Manual, Rev. H
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 79
  • Seagate ST9900805SS | Savvio 10K.3 SAS Product Manual - Page 80
    Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Product Manual
Savvio
®
10K.3 SAS
100516229
Rev. H
December 2011
Standard Models
ST9300603SS
ST9146803SS
Self-Encrypting Drive Models
ST9300503SS
ST9146703SS
SED FIPS 140-2 Models
ST9300403SS
ST9146603SS