Sharp DVENDFSV DVENDFSV Vendor Interface Install Guide
Sharp DVENDFSV Manual
View all Sharp DVENDFSV manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp DVENDFSV manual content summary:
- Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 1
Installation Instructions for DVENDFSV External Vendor Interface Cable Kit Models: MX-M3071S / MX-M3571S / MX-M4071S / MX-M5071S / MX-M6071S (For installation by a Sharp authorized technician) Kit - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 2
Step 3: • Remove the 1 screw and remove the ROM cover. • Remove 6 screws and remove the rear cover. Step 4: • Back cover removed Screw - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 3
Step 5: • Prepare the cable • Fasten the cable ties to the cable. •Pay attention to the fastening direction of the tie to ensure proper mounting direction. •The extra end of the tie should be cut off with 1-2 mm remained. Step 6: •Insert the connector onto the PCU PWB. - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 4
Step 7: • Position the cable as shown below • Fasten the ground wire as shown in the 2nd picture. Pay attention to the position of the round terminal mount. Step 8: • Open the cut out on the ROM Cover and pass the wire through the hole. Attach the cover with 1 screw. - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 5
Step 9: • Re-install the rear cover using 6 screws. Step 10: • Re-attach the ROM cover using 1 screw. - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 6
Reference: Enter to Simulation Mode • Enter password entry screen in the same way with current model. • Enter password to log into pass code entry screen. (new) • Enter pass code to log into Simulation Mode . 1. Password is needed.(for service) (new) 2. Pass code is needed. - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 7
Reference: New Simulation Mode (new) • After pass code is entered, Easy Simulation Mode is displayed. • Simulation Mode is switchable by button. • Default Simulation Mode is Normal Mode. Normal Mode Button to switch Easy Mode Button to switch - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 8
Step 11: Enable the Vendor Mode • Enter simulation 26-3 • Refer to screen shot below - On the line for Outside Auditor, select "P Vendor 1'' Default Screen for Simulation 26-3 Vendor mode turned on - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 9
Step 12: Optional Settings: Document Filing • Refer to the screen shot below - On the line for DOC ADJ, select "ON'' to enable Document Filing. The default setting is OFF. Screen with previous setting turned on for Simulation 26-3: Doc ADJ turned on - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 10
Step 13: Optional Settings: Continuous Paper Feeding Refer to the screen shot below - On the line for PF ADJ, select "ON'' to enable Continuous Paper Feeding. The default setting is OFF. Screen with previous settings turned on for Simulation 26-3: PF ADJ turned on - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 11
Step 14: Optional Settings: Vendor Mode Refer to the screen shot below - On the line for VENDOR MODE, select MODE 1, MODE 2, or MODE 3 based on the preferred setting shown in the Condition Table below. The default setting is MODE 3. Condition Table Mode 1 Mode 2 Mode 3 The specified number of - Sharp DVENDFSV | DVENDFSV Vendor Interface Install Guide - Page 12
Step 15: Optional Settings: Count-up Timing • Refer to the screen shot below - On the line for COUNTUP TIMING, ο Select FUSER_IN to change the count-up timing to when the lead edge of the paper passes over the sensor after fusing ο Select FUSER_OUT to change the count-up timing to when the trail
Kit Contents:
•
(1) Vendor Interface Cable
•
(1) 8″ Stress Relief Tie
•
(3) 4″ Nylon Mounting Ties
•
(1) #8 x ¾″ Self Tapping Screw
•
(1) #8 SAE Washer
Installation Instructions for DVENDFSV External Vendor Interface Cable Kit
Models: MX-
M
3071S / MX-
M
3571S / MX-
M
4071S / MX-
M
5071S / MX-
M
6071S
(
For installation by a Sharp authorized technician)
Step 1:
•
Prepare the cable for installation.
•
Have other installation accessories at hand.
Step 2:
•
Ensure machine is turned off and unplugged
from wall outlet
•
Disconnect Network and Fax line
(if equipped)