Sharp KB-0333KW KB-0333K Operation Manual / Installation Instructions
Sharp KB-0333KW Manual
 |
View all Sharp KB-0333KW manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp KB-0333KW manual content summary:
- Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 1
1 1 " KB-0333K &OLLOWED - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 2
OF PURCHASE DEALER SERVICER / / SERIAL NUMBER TELEPHONE TELEPHONE TO PHONE: DIAL DIAL 1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for telephone number (including area code) and description of the problem. TO ACCESS INTERNET: www.sharpusa.com 2 - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 3
. If it is necessary to remove the unit for repair, the servicer will reinstall the unit at no extra charge, provided it was installed according to Sharp's Installation Instructions. TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP or visit www.sharpusa.com. SAVE THE PROOF OF - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 4
Sharp at the address or telephone number listed on page 2 of this manual. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service medium settings. Installer: Leave this manual with the homeowner. Homeowner: Operating instructions and Cleaning information are on - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 5
LINE ELECTRICAL ACCESS HOLE (In wall) 7" ROUND VERTICAL DUCTING (Recessed-bottom (In cabinet bottom) NON-DUCTED (Recessed-bottom (In cabinet bottom) 3 Run house wiring between service panel and hood location. 5 - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 6
PREPARE THE HOOD 1 Remove 7" Round Duct Plate from top of hood. Set duct plate aside - with mounting screws. 2 Remove tape holding Filters in place. Pull down on filter tabs or finger holes and lift filters out. Set filters aside. 3 Remove Teflon®Coated Bottom Cover from hood. Set cover and - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 7
10 Re-install air chute and screw, re-connect wire harness and replace light panel. Note: Be careful not to trap wires between Support Fin and light panel. 11 Remove appropriate Duct Knockout(s) from top or back of hood. PREPARE THE HOOD 13 3 1⁄4" x 10" Ducted Discharge Only: Remove tape - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 8
EDGE MOTOR SLOTS PERFORMANCE RING CONNECT WIRING WARNING To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. 1 Connect House Wiring (120 VAC) to hood. Use a piece of cardboard to - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 9
make joints secure and air tight. 5 Replace filters, turn on power at service panel and test for proper operation. If hood is to be installed Non- filters, model KBK-330, from your local distributor, retailer or from Sharp (see page 2). NON-DUCTED FILTERS • Attach charcoal filters to the aluminum - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 10
to turn off the indicator light. 2 4 HEAT SENSOR Your Sharp Insight Range Hood is equipped with an advanced Heat Sensor. The supply stores have them in stock. To replace the fuse: 1. Disconnect power at service entrance. 2. Remove filters, bottom panel, light wire harness and air chute. 3. - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 11
WARNING To reduce the risk of electric shock, disconnect from power supply before cleaning. Aluminum mesh filters: Clean frequently using hot water and a mild detergent. Filters are dishwasher safe. Charcoal filters (additional filters for non- ducted installations): Clean filter surfaces frequently - Sharp KB-0333KW | KB-0333K Operation Manual / Installation Instructions - Page 12
- This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. SHARP ELECTRONICS CORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 626995B PRINTED IN USA
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
I
NSIGHT
R
ANGE
H
OOD
KB-0333K