Sharp PG-F255W PG-F255W Setup Manual

Sharp PG-F255W - Notevision WXGA DLP Projector Manual

Get Sharp PG-F255W - Notevision WXGA DLP Projector PDF manuals and user guides
UPC - 074000365759
View all Sharp PG-F255W manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp PG-F255W manual content summary:

  • Sharp PG-F255W | PG-F255W Setup Manual - Page 1
    PROJECTOR MODEL PG-F255W SETUP MANUAL Connecting Pin Assignments 2 RS-232C Specifications and Commands .......... 4 Setting up the Projector Network Environment ... 9 1. Connecting the Projector when an Error Occurs (Service & Support - Access URL 19 Setting up the Projector Using RS-232C or
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 2
    Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini Dsub 15 pin female connector 11 15 1 5 6 10 COMPUTER Input/Output Pin No. Signal 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. Not
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 3
    RS CS CI Note • Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Projector Pin No. 4 5 6 Computer Pin No. 4 5 6 USB Terminal : Type B USB connector 43 Pin No. Signal Name 1. VCC USB power 2. USB- USB data
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 4
    type, commercially available) to the projector. (See page 24 of the projector's operation manual for connection.) Communication conditions Set the Problem response (communication error or incorrect command) O K Return code (0DH) E R R Return code (0DH) Info • When controlling the projector
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 5
    Lamp Life 5% or less 2: Fan Error 16: Lamp Burn-out 4: Cover Open 32: Lamp Ignition Failure 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp PGF255W M N R D _ _ _ 1 PG-F255W 0:Standby P J N 1 * * * * OK or ERR P J N 2 * * * * OK or ERR P J N 3 * * * * OK or ERR P J N 0 _ _ _ 1 Projector
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 6
    DVI INPUT CONTROL CONTENTS S-Video Video Normal Stretch Area Zoom V-Stretch Normal Stretch Area Zoom V-Stretch Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp BrilliantColorTM Progressive DNR Picture Reset Signal Type Audio Input Picture Mode Contrast Bright Red Blue Color Tint
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 7
    Movie Game Contrast -30 - +30 Bright -30 - +30 Red -30 - +30 Blue -30 - +30 Color -30 - +30 Tint -30 - +30 Sharp -30 - +30 CLR Temp -1 - +1 BrilliantColorTM 0 - +2 Progressive 2D Progressive 3D Progressive Film Mode DNR Off Level 1 Level 2 Picture Reset Audio Input Audio
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 8
    çais Italiano Svenska Português Setup Guide System Sound Internal Speaker RGB Frequency Check Fan Mode Lamp Timer Reset *3 polski Türkçe ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR OK or ERR *1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *2 This command
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 9
    settings may need to be changed. Please consult your network administrator for assistance with these settings. You can make network settings both on the projector and on the computer. The following procedure is for making settings on the computer. Network settings on the computer 1. Connecting the
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 10
    's LAN terminal and connect the other end of the cable to the computer's LAN terminal. 3 Plug the power cord into the AC socket of the projector. A LAN cable being connected to the network LAN cable (cross-over type, commercially available) 4 Turn on the computer. ON Info Confirm that the LINK LED
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 11
    Setting up the Projector Network Environment 2. Setting an IP Address for the Computer status and tasks" of "Network and Internet", and click "View status" in the new window. • This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click 1 "
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 12
    IP address : 192.168.150.3 Subnet mask : 255.255.255.0 Default gateway : (Do not input any values.) Note • The factory default settings for the projector are as follows: DHCP Client : OFF IP address : 192.168.150.2 Subnet mask : 255.255.255.0 Default gateway : 0.0.0.0 7 After setting, click the "OK
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 13
    's IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. (See page 50 of the projector's operation manual for setting.) DHCP Client : Off IP Address : 192.168.150.002 Subnet Mask : 255.255.255.000 1 Start Internet Explorer (version 5.0 or
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 14
    . If "192.168.150.2" is not used in the network having an IP address of "192.168.150.XXX", you don't have to change the projector IP address. • For details about each setting, consult your network administrator. 5 Click the "Apply" button. 6 The set values appear. Confirm that the values are set
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 15
    to external equipment before starting the operation. (See pages 2125 of the projector's operation manual.) Complete the AC cord connection. (See page 25 of the projector's operation manual.) Note • When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 16
    can confirm the projector status. You can confirm the following items : • MAC Address • Power • Condition • Lamp Timer • Lamp Life • Input For details about each item, refer to the projector's operation manual. On this screen, you can perform projector control. You can control the following items :
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 17
    • DNR • Lamp Setting • Resolution Setting • Signal Type • Video System • Dynamic Range • Resize • OSD Display • Background • Setup Guide • Projection Mode this page while the projector is warming up. • For details about each item, refer to the projector's operation manual. On this screen, you
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 18
    Remarks Setting an SMTP server address for e-mail transmission. e.g.1 : 192.168.150.253 e.g.2 : smtp123.sharp.co.jp * When using a domain name, make settings for the DNS server. Setting the projector's e-mail address. The e-mail address set here becomes Originator E-mail Address. Setting the sender
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 19
    Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail - Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support error (Lamp, Temp projector's operation manual. On this
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 20
    to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector. When Connecting Using RS-232C 1 Launch general purpose terminal emulator. 2 Input settings for the RS-232C port of the terminal emulator as follows. Baud Rate
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 21
    theWindows® desk- top and select "Run". 2 Enter"telnet 192.168.150.2"in the text box that opens up. (If the IP address of the projector is 192.168.150.2.) 3 Click the "OK" button. ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 22
    Addr (Factory default setting : Ac- cept All) For improved security, it is possible to set up to three IP addresses allowing connection to the projector. Set IP addresses can be cancelled using [9] Accept All IP Addr. (Page 28) [0] Search Port (Factory default setting : 5006) Setting the port number
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 23
    Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v 1 Model Name : XX-XXXX Projector Name : XX-XXXX MAC Address : XX:XX:XX:XX:XX:XX DHCP Client : Disable IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 24
    quit menu. ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>s 1 All Connection will be
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 25
    mask after change (*). Note • If the values for IP Address, Subnet Mask or Gateway of the projector have been changed via Telnet, the computer cannot be connected to the projector depending on the computer's network settings. User Name Setting ([4]User Name) Carrying out security protection using
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 26
    Name : XX-XXXX Please Enter : MY XX-XXXX 2 (change) -> MY XX-XXXX * 1 Enter "7" and press the "Enter" key. 2 Enter projector name. Display set projector name (*). Note • Password can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ • In the default state, the
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 27
    ([D]Disconnect All) It is possible to disconnect all the TCP/IP connections currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection. setup>d 1 Disconnect
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 28
    RS-232C or Telnet Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is working normally. advanced>5 1 Ping Test IP addr :192.168.150.1 Please Enter :192.168.150.152 2 (change) -> 192
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 29
    RS-232C or Telnet Setting of Search Port (ADVANCED[0]Search Port) Sets the port number used when searching for the projector from the network. advanced>0 1 Please Enter Port Number for Search from Computer. Valid range : 1025 to 65535 Search Port : 5006 Please Enter : 5004 2 (change
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 30
    Lamp Timer of the Projector via LAN When the projector is connected to a network, you can use the communications program to send a command to reset the lamp ". • If you do not have HyperTerminal installed, see the operation manual of your computer. • Depending on the settings of your computer, you
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 31
    Properties window appears, click "OK". 8 If a user name and/or password is set for the projector, enter the user name and password. 9 Send the lamp reset command "LPRE0001". • This command can only be sent when the projector is in standby mode. • When "OK" is received, this indicates that the
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 32
    Troubleshooting Communication cannot be established with the projector When connecting the projector using serial-connection \ Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly. \ Check that the RS-232C cable is a cross-
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 33
    Troubleshooting \ Take the following steps for checking the network settings for the computer. 1. Open a command prompt. • In the case of Windows® 2000: click "start" ➔ "Programs" ➔ "Accessories" ➔ "
  • Sharp PG-F255W | PG-F255W Setup Manual - Page 34
    Troubleshooting \ Check if the "TCP/IP" protocol is operating correctly using the "PING" command. Also, check if an IP have forgotten your user name or your password. \ Initialize the settings. (See page 51 of the projector's operation manual.) \ After the initialization, carry out setting again. -34
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
MODEL
PG-F255W
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments
............................
2
RS-232C Specifications and Commands
..........
4
Setting up the Projector Network Environment ...
9
1. Connecting the Projector to a Computer
..........
10
2. Setting an IP Address for the Computer
..........
11
3. Setting up a Network Connection for the Projector ..
13
Controlling the Projector via LAN
....................
15
Controlling the Projector Using Internet Explorer
(Version 5.0 or later)
...................................
15
Confirming the Projector Status (Status)
.............
16
Controlling the Projector (Control)
.......................
16
Setting and Adjusting the Projector
(Settings & Adjustments)
............................
17
Setting the Security (Network – Security)
............
17
Making General Settings for the Network
(Network – General)
..................................
18
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings)
.......................
18
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ... 19
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL)
...........
19
Setting up the Projector Using RS-232C or Telnet
....
20
When Connecting Using RS-232C
.......................
20
When Connecting Using Telnet
............................
21
SETUP MENU (Main Menu)
.................................
22
ADVANCED SETUP MENU
.................................
22
View Setting Detail List ([V]View All Setting)
.......
23
Set Items
...............................................................
23
Save Settings and Quit ([S]Save & Quit)
.............
24
Quit without Saving Settings ([Q]Quit Unchanged) ..
24
IP Address Setting ([1]IP Address)
......................
25
Subnet Mask Setting ([2]Subnet Mask)
...............
25
Default Gateway Setting ([3]Default Gateway)
....
25
User Name Setting ([4]User Name)
.....................
25
Password Setting ([5]Password)
..........................
26
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate)
............................
26
Projector Name Setting ([7]Projector Name)
.......
26
DHCP Client Setting ([8]DHCP Client)
.................
26
Disconnecting All Connections
([D]Disconnect All)
.....................................
27
Entering ADVANCED SETUP MENU
([A]Advanced Setup)
..................................
27
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
.............
27
Data Port Setting (ADVANCED[2]Data Port)
.......
27
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test)
............
28
Setting of Accept IP Address (ADVANCED[6]Accept
IP Addr(1) – [8]Accept IP Addr(3))
................
28
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
............
28
Setting of Search Port
(ADVANCED[0]Search Port)
......................
29
Return to Default Settings
(ADVANCED[!]Restore Default Setting)
............
29
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
..............
29
Resetting the Lamp Timer of the Projector
via LAN
.......................................................
30
Troubleshooting
.................................................
32