Sharp PN-Y436 PN-Y326 PN-Y436 PN-Y496 PN-Y556 Operation Manual
Sharp PN-Y436 Manual
View all Sharp PN-Y436 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp PN-Y436 manual content summary:
- Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 1
PN-Y556 PN-Y496 PN-Y436 PN-Y326 LCD MONITOR OPERATION MANUAL - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 2
IMPORTANT: To aid reporting in case of loss or theft, please record the product's model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No.: Serial No.: U.S.A. ONLY - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 3
user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: FCC Regulations and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 4
SHARP LCD product. To ensure safety and many years of trouble service life of your LCD product, please read the following precautions carefully before using the product. 1. Read instructions - All operating instructions must be read and understood before the product is operated. 2. Keep this manual - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 5
spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • sides of the batteries according to the instructions in the compartment. • Do not mix reaction control in nuclear facility, medical life support system, and missile launch control in a weapon - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 6
block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 7
INSTRUCTIONS - The TFT color LCD phenomena of LCDs and will not affect the performance of the monitor. - Do not display a still from an authorized SHARP servicing dealer or service center. - Images or malfunctioning. Refer the servicing to the service representative. Manual Scope - Microsoft - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 8
work must be performed by an authorized SHARP dealer. You should never attempt to the monitor at the ambient temperature within the range of 32°F (0°C) to 86°F (30°C). Provide 7-7/8 inch (200 required range. - Do not press hard on the LCD panel or otherwise subject it to impacts. Flat installation - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 9
play 24 Settings 25 Supported formats 26 Menu Items 27 Displaying the menu screen 27 Troubleshooting 44 Specifications 46 Mounting Precautions (For SHARP dealers and service engineers 52 Supplied Components If any components are missing, please contact your dealer. Liquid Crystal Display - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 10
monitor. 56 16 17 18 19 23 8 20 22 21 3 10 11 12 13 14 15 4 1. LCD panel 2. Power LED / Remote control sensor (See pages 18,17.) 3. Power button (See page 18.) 4. Kensington MicroSaver Security System. Caution • Consult your SHARP dealer for attachment/detachment of optional parts. E 10 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 11
button (See page 18.) 3. MUTE button (See page 20.) 4. VOL +/- buttons (See page 20.) BRIGHT +/- buttons (See page 20.) Cursor control ( / / / ) buttons 5. DISPLAY/Red button (See page 20.) 6. MODE/Green button (See page 21.) 7. INPUT button (See page 20.) 8. MENU button (See page 20.) 9. ENTER - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 12
cables. Also, read the manual of the equipment to be cause malfunctions and the other problems. • Do not use any when a computer screen is displayed for the first time using info" in the root folder. Supported USB flash drives File System Capacity FAT32 Up to 32 GB (maximum file size 2 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 13
: - PN-Y556/PN-Y496/PN-Y436/PN-Y326 - PN-Y555/PN-Y475/PN-Y425/PN-Y325 11 memory cards (up to 32GB) are supported. The explanations in this manual refer to both SD memory cards info" in the root folder. Supported SD memory cards File System FAT32 Capacity Up to 32 GB (maximum file size 2 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 14
Connecting the Power Cord Caution • Use only the power cord supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Main power switch 1 For power outlet 3 Power cord ( - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 15
Setting the USB flash drive cover 1. Insert the USB flash drive into the USB port. 2. Attach the USB flash drive cover and secure with the provided screw. Power supply USB port terminal Screw TIPS • If the USB flash drive will be attached, use a USB flash drive with dimensions no greater than - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 16
Attaching the logo sticker You can attach the supplied logo sticker on the monitor. Refer to the following example to attach the sticker as necessary. Example for landscape orientation Example for portrait orientation E 16 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 17
the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow. 2. See the instructions in the compartment and put in the supplied batteries (R-6 ("AA" size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Close the cover - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 18
the power ON/OFF. Turning on the main power When the main power is turned on, the power LED lights. Wait until the screen is displayed. POWER button Main power switch Status Green lit Orange lit Green flashing Power LED Status of the monitor Power on Power off (Standby mode) Input - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 19
nDate/time setting • If the time has not been set, such as when the monitor is first turned on, set the date and time in DATE/TIME SETTING of the SETUP menu. Be sure to set the date and time. TIPS • Set the time on a 24-hour basis. • The clock stops if the main power remains off for about 1 week.* - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 20
SD memory card connected. 2. MUTE Turns off the volume temporarily. Press the MUTE button again to turn the sound back to the previous level. 3. MENU Displays and turns off the menu screen. (see page 27.) 31 Press or to adjust the brightness. * If you do not press any buttons for about - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 21
→ sRGB→ HIGH ILLUMINANCE → Media Player → STD... • HIGH ILLUMINANCE is a display with colors suited to bright locations. • sRGB is for DVI-D, HDMI[PC], SD memory card is being played. (See page 25.) TIPS • 8 SIZE , 9 , DISPLAY and 10 MODE are also used when playing a file in a USB flash drive or an - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 22
the "autoplay" folder that meet the criteria below play automatically. (Supported formats and file names are different from other playback.) Format Image files • Mixed playback of image files and video files is not possible. To display a mix of image files and video files, see "SCHEDULE" (see page - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 23
• For the types of files that can be played and cautionary points, see "Supported formats". (See page 26.) 1. Insert a media to be played (the USB be played, and the play method. (See the description below.) TIPS • The displayed screen size is as follows: Image: Dot by Dot Video: NORMAL, WIDE, - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 24
as they are of the same type. Mixed file types are not played. • To return to the next higher item, press or . RETURN • When displaying the video file list, the thumbnails of some files may take time to appear. Wait until the thumbnails appear before performing the next operation. Playing - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 25
of a file, or files in a folder, is repeated. Play Once.... Do not repeat Repeat......... Play repeatedly Slideshow Time (Only during [Folder] or [Photo] display.) Set the slideshow change time. This setting is also applied to auto play and schedule play. The times below are general guidelines, and - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 26
format is supported. • A maximum of 32 alphanumeric characters can be used for folder name and file name. A file name or folder name may not display correctly if product failure or problem. • Operation is not assured when a non-supported format is used. The following types of problems may occur: - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 27
. 1 Name of the menu nExample of operation 2 An item being selected (highlighted) (Adjusting CONTRAST in the PICTURE menu) MENU 1. Press to display the menu screen. SCREEN PICTURE AUDIO SETUP H/V-POS SIZE RESET 2. Press or to select PICTURE, and press . ENTER 3. Press or to select - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 28
the sharpness of the image. COLOR ADJUSTMENT COLOR MODE Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See page 21.) * sRGB is DVI-D, HDMI[PC], D-SUB[RGB] input only. See page 21 for details. WHITE BALANCE THRU Displays the - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 29
(number of monitors) in the horizontal/vertical direction used for the enlargement. ENLARGE-POS Specify the split screen to be displayed when the enlargement function is used. (See page 32.) BEZEL ADJUST When ENLARGE is set to ON, sets whether or not to use the frame correction function. THERMAL - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 30
operation from the remote control unit, RS-232C commands, or LAN for more than the set time. POWER ON DELAY You can delay the screen display after the monitor is turned on. The period can be set up to 60 seconds in units of 1 second. When this function is activated, the - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 31
Menu Items POWER MANAGEMENT POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode. AUTOPLAY (See page 22.) Set the type of file to be automatically played from a USB flash drive or an SD memory card. SUPPLY USB POWER ON Power can be supplied from - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 32
of monitors aligned in the vertical direction in ENLARGE V. 5. Set the section of the separated image to be displayed on each monitor in ENLARGE-POS. 1) Press . ENTER 2) Press or to select position, then press . 7 11 15 2 6 10 14 1 5 9 13 3 8 13 18 23 2 7 12 17 22 1 6 11 16 21 E 32 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 33
input mode at power on with or . (6) PLAYLIST SETTING This only appears when INPUT is set to [Media Player]. Use to create a playlist for automatic display/playback of files in a media. • Image files and video files can be combined in the same playlist. • Audio files cannot be used. • Up to 30 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 34
click [Adj_uty.exe]. The adjustment pattern will appear. Adjust the screen automatically or manually. TIPS • Up to 3 SCHEDULE items can be registered. • Setting the 5. Eject the CD-ROM from the CD-ROM drive. TIPS • If the display mode on the computer you are using is 65,000 colors, the color levels - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 35
+, -, space, ?) RS-232 straight cable (commercially available) RS-232C input terminal nDaisy chain connection... Advanced operation PN-Y556/PN-Y496/PN-Y436/PN-Y326 or PN-Y555/PN-Y475/ PN-Y425/PN-Y325 monitors can be connected together in a daisy chain connection. Connect with RS-232 straight cable - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 36
Controlling the Monitor with a computer (RS-232C) nResponse code format When a command has been executed correctly O K Return code (0DH, 0AH) A response is returned after a command is executed. * If an ID number has been assigned Space (20H) Return code (0DH, 0AH) O K SPC 0 0 1 ID number of - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 37
Controlling the Monitor with a computer (RS-232C) nCommands for ID control The command examples shown on this page assume the following connection and ID SETTING. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDLK The parameter of this command sets the ID number of the monitor. The monitor - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 38
Controlling the Monitor with a computer (RS-232C) nRepeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [ - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 39
Controlling the Monitor with a computer (RS-232C) RS-232C command table How to read the command table Command: Direction: Parameter: Reply: * : Command field (See page 35.) W When the "Parameter" is set in the parameter field (see page 35), the command functions as described under "Control/ - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 40
Controlling the Monitor with a computer (RS-232C) SETUP menu Function Command Direction Parameter Reply Control/Response contents * DATE/TIME SETTING DATE WR AABBCCDDEE AABBCCDDEE AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute LAN SETUP DHCP client DHCP WR 0-1 0-1 0: OFF, 1: ON - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 41
Controlling the Monitor with a computer (RS-232C) Others Function VOLUME MUTE INFORMATION MODEL SERIAL NO TEMPERATURE SENSOR Command Direction VOLM WR MUTE WR INF1 R SRNO R DSTA R Parameter 0-31 0-1 TEMPERATURE ACQUISITION ERRT R CAUSE OF LAST STANDBY MODE STCA W 0 R Reply - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 42
SETUP options. (See page 29.) After setting each item, press . RETURN SETTING DISPLAY Shows the LAN SETUP settings. DHCP CLIENT If your LAN has a DHCP server an address automatically, change this setting to ON. To set the address manually, set this to OFF. IP ADDRESS If the DHCP CLIENT is set to - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 43
can control the monitor using RS-232C commands (see page 39) via terminal software and other appropriate applications. Read the manual for the terminal software for detailed instructions. (1) Connect the computer to the monitor. 1. Specify the IP address and data port number (fixed at "10008"), and - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 44
If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips. There is no play properly. • Is the file in a supported format? (See page 26.) The following problems may occur if a non-supported format is used: - The file does not - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 45
to prevent high-temperature-related problems. When this occurs, the Power mode due to a rise in temperature, to return to normal display, turn the power switch off and then back on again. the vents. Remove dust if possible. Ask SHARP dealer about removing internal dust. - If Troubleshooting 45 E - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 46
PN-Y556 PN-Y496 PN-Y436 PN-Y326 LCD component 55" Class 49" Class 43" Class 32" Class [54-5/8 inch [48-1/2 inch [42-1/2 inch [31-9/16 inch (138.78cm) diagonal] (123.20cm) diagonal] (107.98cm) diagonal] (80.13cm) diagonal] TFT LCD TFT LCD TFT LCD TFT LCD improvement, SHARP reserves - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 47
534]) 22 [559] 11-1/8 [282.5] 8 [203] [15.5] [10.5] 1-13/16 [46] [PN-Y326] 28-1/2 [724.5] 7/16 [10.5] Opening width (27-11/16 [703.5]) 7/16 5/8 11/16 wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 48
Power consumption* 105 W 87 W 76 W 69 W 7.0 W 7.0 W 7.0 W 7.0 W * Values of the PN-Y556, PN-Y496, PN-Y436, and PN-Y326 in that order from the top. nDDC (plug and play) The monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for plug and play between monitors and - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 49
image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed. • Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input. nCompatible signal timing (AV) Screen resolution 1920 × 1080p 1920 - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 50
Specifications nDVI-D input terminal pins (DVI-D 24 pin) nHDMI input terminal pins (HDMITM Connector) No. Function 1 TMDS data 2- 2 TMDS data 2+ 3 TMDS data 2/4 shield 4 N.C. 5 N.C. 6 DDC clock 7 DDC data 8 N.C. 9 TMDS data 1- 10 TMDS data 1+ 11 TMDS data 1/3 shield 12 N.C. No. - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 51
nDVI-D output terminal pins (DVI-D 24 pin) Specifications nRS-232C output terminal pins (D-sub 9 pin) No. Function 1 TMDS data 2- 2 TMDS data 2+ 3 TMDS data 2/4 shield 4 N.C. 5 N.C. 6 DDC clock 7 DDC data 8 N.C. 9 TMDS data 1- 10 TMDS data 1+ 11 TMDS data 1/3 shield 12 N.C. No. - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 52
Mounting Precautions (For SHARP dealers and service engineers) • When installing, removing or moving the driver. • When moving the monitor, hold the parts marked by below. Do not hold the LCD panel. This may cause product damage, failure, or injury. • After mounting, please carefully ensure - Sharp PN-Y436 | PN-Y326 | PN-Y436 | PN-Y496 | PN-Y556 Operation Manual - Page 53
PN-Y556-Y496-Y436-Y326 M EN16J(1)
PN-Y556
PN-Y496
PN-Y436
PN-Y326
LCD MONITOR
OPERATION MANUAL