Sharp XG-P560W XG-P560W Setup Manual
Sharp XG-P560W - WXGA DLP Projector Manual
 |
View all Sharp XG-P560W manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp XG-P560W manual content summary:
- Sharp XG-P560W | XG-P560W Setup Manual - Page 1
DATA PROJECTOR MODEL XG-P560W XG-P560W-N SETUP MANUAL Setting up the Screen 2 Screen Size and Projection Distance 3 Connecting Pin Assignments 11 Wired Remote Control Terminal Specifications ...... 13 RS-232C Specifications and Commands ........ 14 Setting up the Projector Network Environment - Sharp XG-P560W | XG-P560W Setup Manual - Page 2
of standard setup Side View H1 Screen Center of screen H2 L Top View Screen Lens center • The distance from the screen Lower lens shift position to the projector may vary (High mount setup) depending on the size of the screen. Lens center Upper lens shift position (Desktop setup) • The - Sharp XG-P560W | XG-P560W Setup Manual - Page 3
screen size varies according to the distance from the lens of the projector to the screen. The optional lenses from Sharp are also available for specialized application. Please see your nearest Sharp Authorized Projector Dealer to details on all the lenses. (Refer to the lens operation manual - Sharp XG-P560W | XG-P560W Setup Manual - Page 4
and Projection Distance Standard Zoom Lens (AN-P18EZ : Standard Equipment with XG-P560W) F2.5, f=25.5-32 mm 16:10 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [χ] Width Height Minimum [L1] Maximum - Sharp XG-P560W | XG-P560W Setup Manual - Page 5
Distance Fixed Wide Lens (AN-P8EX) F2.5, f=11.6 mm 16:10 Signal Input (Normal Mode) Picture (Screen) size Diag. [χ] -0.37689χ / 2.54 W (in) = ±0.23691χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Diag. [χ] Width 120'' (305 cm) 244 cm (96'') 100'' (254 cm) 203 cm (80'') 80 - Sharp XG-P560W | XG-P560W Setup Manual - Page 6
Fixed Wide Lens (AN-P12EX) F2.5, f=17.1 mm 16:10 Signal Input (Normal Mode) Picture (Screen) size Projection distance 2.54 W (in) = ±0.23691χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance Diag. [χ] Width Height 200'' (508 cm) 406 cm (160'') 305 cm (120 - Sharp XG-P560W | XG-P560W Setup Manual - Page 7
3048 H1 (in) = -1.56815χ / 2.54 H2 (in) = 0.2221χ / 2.54 W (in) = ±0.75379χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [χ] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2 - Sharp XG-P560W | XG-P560W Setup Manual - Page 8
3048 H1 (in) = -1.56815χ / 2.54 H2 (in) = 0.2221χ / 2.54 W (in) = ±0.75379χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [χ] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2 - Sharp XG-P560W | XG-P560W Setup Manual - Page 9
3048 H1 (in) = -1.56815χ / 2.54 H2 (in) = 0.2221χ / 2.54 W (in) = ±0.75379χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [χ] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2 - Sharp XG-P560W | XG-P560W Setup Manual - Page 10
3048 H1 (in) = -1.56815χ / 2.54 H2 (in) = 0.2221χ / 2.54 W (in) = ±0.75379χ / 2.54 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [χ] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2 - Sharp XG-P560W | XG-P560W Setup Manual - Page 11
Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini D-sub 15 pin female connector 10 6 5 1 15 11 RGB Input 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. Not connected 6. Earth (red) 7. Earth - Sharp XG-P560W | XG-P560W Setup Manual - Page 12
CI Note • Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Projector Pin No. 4 5 6 Computer Pin No. 4 5 6 LAN Terminal: LAN (RJ-45) Pin No. 1 2 3 4 Signal TX+ TX- RX+ 8 ... 1 Pin No. 5 6 7 8 Signal RX- -12 - Sharp XG-P560W | XG-P560W Setup Manual - Page 13
0 FOCUS - 1 0 1 1 01 0 1 0 0 1 11 1 0 SHUTTER CLOSE 1 0 1 1 0 1 1 0 0 1 0 0 1 1 0 H&V LENS SHIFT 1 0 1 1 0 0 0 1 1 0 0 0 1 1 0 MUTE 1 0 1 1 01 1 1 0 1000 1 0 KEYSTONE 1 0 1 1 01 indicating "Front" and "01" indicating "Rear". Sharp remote control signal format Transmission format: 15-bit - Sharp XG-P560W | XG-P560W Setup Manual - Page 14
to the projector. (See page 27 of the projector's operation manual for connection.) problems.) Note • When controlling the projector using the RS-232C commands, you cannot confirm the projector , the settings/adjustments are executed without the on-screen display. • If an underbar (_) appears in - Sharp XG-P560W | XG-P560W Setup Manual - Page 15
_ 2 0% - 100% (Integer) L P R E 0 0 0 1 ERR L P R E 0 0 0 2 ERR T N A M _ _ _ 1 XGP560W M N R D _ _ _ 1 XG-P560W S N R D _ _ _ 1 Serial No. P J N 1 * * * * OK or ERR P J N 2 * * * * OK or ERR P J N 3 * * * * OK or ERR P J N 0 _ _ _ 1 Projector Name I R G B _ _ _ 1 OK or ERR I R G B _ _ _ 2 OK or ERR - Sharp XG-P560W | XG-P560W Setup Manual - Page 16
Contrast -30 - +30 Bright -30 - +30 Color -30 - +30 Tint -30 - +30 Red -30 - +30 Green -30 - +30 Blue -30 - +30 Sharp -30 - +30 CLR Temp *4 Progressive 2D Progressive 3D Progressive Film DNR Off Level 1 Level 2 Level 3 Adjustment Reset Signal Type Auto RGB Component - Sharp XG-P560W | XG-P560W Setup Manual - Page 17
Custom Contrast -30 - +30 Bright -30 - +30 Color -30 - +30 Tint -30 - +30 Red -30 - +30 Green -30 - +30 Blue -30 - +30 Sharp -30 - +30 CLR Temp *4 Progressive 2D Progressive 3D Progressive Film DNR Off Level 1 Level 2 Level 3 Adjustment Reset Signal Type D. PC RGB D. PC - Sharp XG-P560W | XG-P560W Setup Manual - Page 18
-30 - +30 Bright -30 - +30 Color -30 - +30 Tint -30 - +30 Red -30 - +30 Green -30 - +30 Blue -30 - +30 Sharp -30 - +30 CLR Temp *4 Progressive 2D Progressive 3D Progressive Film DNR Off Level 1 Level 2 Level 3 Adjustment Reset Display (Status display) C.M.S. COMPUTER1 - Sharp XG-P560W | XG-P560W Setup Manual - Page 19
Startup Image Selection Eco Mode Auto Search Auto Power Off Lamp Mode Lens Type PRJ Mode Stack Setting Keylock Level Set Inputs Fan Mode the RS-232C function stops, the projector send no response code. *6 See page 65 of the projector's operation manual for the initialized items by using "All - Sharp XG-P560W | XG-P560W Setup Manual - Page 20
settings may need to be changed. Please consult your network administrator for assistance with these settings. You can make network settings both on the projector and on the computer. The following procedure is for making settings on the computer. Network settings on the computer 1. Connecting the - Sharp XG-P560W | XG-P560W Setup Manual - Page 21
1 Disconnect the computer's LAN cable from the existing network. 2 Connect a commercially avail- able LAN cable (UTP cable, Category 5, cross-over type) to the projector's LAN terminal and connect the other end of the cable to the computer's LAN terminal. 3 Plug the power cord into the AC socket of - Sharp XG-P560W | XG-P560W Setup Manual - Page 22
Setting up the Projector Network Environment 2. Setting an IP Address for the Computer status and tasks" of "Network and Internet", and click "View status" in the new window. • This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click 1 " - Sharp XG-P560W | XG-P560W Setup Manual - Page 23
IP address : 192.168.150.3 Subnet mask : 255.255.255.0 Default gateway : (Do not input any values.) Note • The factory default settings for the projector are as follows: DHCP Client : OFF IP address : 192.168.150.2 Subnet mask : 255.255.255.0 Default gateway : 0.0.0.0 7 After setting, click the "OK - Sharp XG-P560W | XG-P560W Setup Manual - Page 24
64 of the projector's operation manual for setting.) DHCP Client : OFF IP Address : 192.168.150.002 Subnet Mask : 255.255.255.000 1 Start Internet Explorer (version 5.0 or later) on the computer, and enter "http://192.168.150.2/" in "Address", and then press the "Enter" key. 2 If a user name and - Sharp XG-P560W | XG-P560W Setup Manual - Page 25
4 The TCP/IP setting screen ap- pears, ready for network settings for the projector. Items Setting example / Remarks having an IP address of "192.168.150.XXX", you don't have to change the projector IP address. • For details about each setting, consult your network administrator. 5 Click the - Sharp XG-P560W | XG-P560W Setup Manual - Page 26
projector's operation manual.) Complete the AC cord connection. (See page 28 of the projector's operation manual.) Note • When connecting the projector Setting up a Network Connection for the Projector" (pages 24, 25), enter "http://192.168.150.2/". 3 A screen for controlling the pro- jector appears, - Sharp XG-P560W | XG-P560W Setup Manual - Page 27
") will be displayed. Wait for a moment and then operate again. • For details about each item, refer to the projector's operation manual. On this screen, you can perform projector control. You can control the following items : • Power • Input Select • Volume • Mute (Audio) • Shutter Note • If you - Sharp XG-P560W | XG-P560W Setup Manual - Page 28
Auto Search • Auto Power Off • Password • Lamp Mode • Lens Type • Projection Mode • Keylock Level • Set projector's operation manual. (The network setting items will not be initialized.) -28 On this screen, you can make settings relating to security. Items Description User Name Setting of user - Sharp XG-P560W | XG-P560W Setup Manual - Page 29
to "A-Z" automatically.) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. Items 168.150.253 e.g.2 : smtp123.sharp.co.jp * When using a domain name, make settings for the DNS server. Setting the projector's e-mail address. The e-mail - Sharp XG-P560W | XG-P560W Setup Manual - Page 30
Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail - Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support - Access URL) On this screen, you can - Sharp XG-P560W | XG-P560W Setup Manual - Page 31
" key. • SETUP MENU will be displayed. ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup - Sharp XG-P560W | XG-P560W Setup Manual - Page 32
projector is 192.168.150.2.) 3 Click the "OK" button. 4 "User Name:"is displayed. Input the user name and press the "Enter" key. • If a user User Name [5]Password [6]RS-232C Baud Rate [7]Projector 2. • User name and password are not set in the factory default settings. • If the user name or - Sharp XG-P560W | XG-P560W Setup Manual - Page 33
-232C or Telnet SETUP MENU (Main Menu) ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup - Sharp XG-P560W | XG-P560W Setup Manual - Page 34
.168.150.2 to 192.168.150.3) ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>1 1 IP - Sharp XG-P560W | XG-P560W Setup Manual - Page 35
Save set values and quit menu. ▼SETUP MENU SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>s 1 All - Sharp XG-P560W | XG-P560W Setup Manual - Page 36
been changed via Telnet, the computer cannot be connected to the projector depending on the computer's network settings. User Name Setting ([4]User Name) Carrying out security protection using user name. setup>4 1 User Name : Please Enter : XX-XXXX 2 (change) -> XX-XXXX * 1 Enter "4" and - Sharp XG-P560W | XG-P560W Setup Manual - Page 37
Name : XX-XXXX Please Enter : MY XX-XXXX 2 (change) -> MY XX-XXXX * 1 Enter "7" and press the "Enter" key. 2 Enter projector name. Display set projector name (*). Note • Password can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ • In the default state, the - Sharp XG-P560W | XG-P560W Setup Manual - Page 38
connections currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force an error message ("Parameter Error!") will be displayed and the screen returns to the ADVANCED SETUP MENU. Entering ADVANCED SETUP MENU ([A]Advanced - Sharp XG-P560W | XG-P560W Setup Manual - Page 39
RS-232C or Telnet Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is working normally. advanced>5 1 Ping Test IP addr :192.168.150.1 Please Enter :192.168.150.152 2 (change) -> 192 - Sharp XG-P560W | XG-P560W Setup Manual - Page 40
Menu) Returns to the main SETUP MENU. advanced>q 1 SETUP MENU [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup - Sharp XG-P560W | XG-P560W Setup Manual - Page 41
be controlled by the remote control. Only while the remote control is connected to the projector with a ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNWGA038WJPZ), the projector set as the slave can be controlled by the remote control. • Even while the - Sharp XG-P560W | XG-P560W Setup Manual - Page 42
(See page 62 on the projector operation manual.) 3 Perform "Pair Stack" of the both projectors. (See page 63 on the projector operation manual.) 4 Select inputs as specified in the table below. (See page 63 on the projector operation manual.) Projector 1 Projector 2 Master Set Inputs COMPUTER1 - Sharp XG-P560W | XG-P560W Setup Manual - Page 43
cable. (See page 24 on the projector operation manual.) 7 Connect the MONITOR OUT (FOR COMPUTER/COMPONENT1, 2) terminal on the projector 1 to the COMPUTER/COMPONENT1 terminal on the projector 2 using an RGB cable. (See page 27 on the projector operation manual.) 8 Connect the LAN terminal on the - Sharp XG-P560W | XG-P560W Setup Manual - Page 44
Video Wall Projection Usually, a costly image-processing device is required to set up a video wall projection. This projector has built-in video wall capability that doesn't require additional equipment. Info • Before setting up the video wall projection, install Internet Explorer (version 5.0 or - Sharp XG-P560W | XG-P560W Setup Manual - Page 45
an example of how to build a 2 X 2 video wall using 4 projectors. COMPUTER/COMPONENT1 terminal Projector 1 RGB cable MONITOR OUT (FOR COMPUTER/ COMPONENT1,2) terminal RGB cable COMPUTER/COMPONENT1 terminal Projector 2 Computer MONITOR OUT (FOR COMPUTER/ COMPONENT1,2) terminal RGB cable COMPUTER - Sharp XG-P560W | XG-P560W Setup Manual - Page 46
Click "Video Wall" on the menu. • "Video Wall" display will appear. 3 Select "2 X 2" on "Division". 4 Click the assigning button for the desired position. • The projector will be assigned to the part of the video wall. Note • For more details on the assigned position and the actual position of the - Sharp XG-P560W | XG-P560W Setup Manual - Page 47
are examples for assigning the projected images for the front and rear projections. Front Projection Rear Projection 1 2 3 4 5 6 1 2 7 8 9 3 4 5 6 7 8 9 The numbers of the projector refer to the numbers of the projected positions. 1 2 3 4 5 6 7 8 9 The numbers of the - Sharp XG-P560W | XG-P560W Setup Manual - Page 48
X 1", "3 X 1", "4 X1", "5 X 1", "6 X 1", "7 X 1" or "8 X 1" on "Division" (see page 46) allows you to create the wide video wall. To create the wide video wall with three projectors lining up in single file from left to right (as shown above), select "3 X 1" on "Division", select a position for each - Sharp XG-P560W | XG-P560W Setup Manual - Page 49
2 : Slave MONITOR OUT (FOR COMPUTER/ COMPONENT1, 2) terminal RGB cable COMPUTER/COMPONENT1 terminal Projector 3: Slave MONITOR OUT (FOR COMPUTER/ COMPONENT1, 2) terminal RGB cable COMPUTER/COMPONENT1 terminal Projector 4 : Slave RGB cable LAN terminal 5BNC to mini D-sub 15 pin cable VIDEO - Sharp XG-P560W | XG-P560W Setup Manual - Page 50
■ Preparation • Follow the procedure below after setting up the basic connection. • When "User Name" and "Password" have been set to the projector, reset them before the stack projection setup. To set "User Name" and "Password", use the same user name and password for both of the master and slave - Sharp XG-P560W | XG-P560W Setup Manual - Page 51
: 192.168.150.4 • Slave 2 : 192.168.150.5 • Slave 3 : 192.168.150.6 9 Click the "Apply" button. 10 Access the projector 2 from the computer via Internet Explorer. (See "Controlling the Projector Using Internet Explorer (Version 5.0 or later)" on page 26 for the details.) 11 Click "Stack" on the menu - Sharp XG-P560W | XG-P560W Setup Manual - Page 52
Video Wall Projection 13 Repeat the same procedure from the step 10 to 12 for the projector 3 and 4. 14 Select inputs as specified in the table on the right. (See page 63 on the projector operation manual.) Note • Set input terminals you will use to "ON". Set input terminals you will not use to - Sharp XG-P560W | XG-P560W Setup Manual - Page 53
Lamp Timer of the Projector via LAN When the projector is connected to a network, you can use the communications program to send a command to reset the lamp ". • If you do not have HyperTerminal installed, see the operation manual of your computer. • Depending on the settings of your computer, you - Sharp XG-P560W | XG-P560W Setup Manual - Page 54
Properties window appears, click "OK". 8 If a user name and/or password is set for the projector, enter the user name and password. 9 Send the lamp reset command. "LPRE0001" for LAMP 1 "LPRE0002" for LAMP 2 • These commands can only be sent when the projector is in standby mode. • When "OK" is - Sharp XG-P560W | XG-P560W Setup Manual - Page 55
Troubleshooting Communication cannot be established with the projector When connecting the projector using serial-connection \ Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly. \ Check that the RS-232C cable is a cross- - Sharp XG-P560W | XG-P560W Setup Manual - Page 56
Troubleshooting \ Take the following steps for checking the network settings for the computer. 1. Open a command prompt. • In the case of Windows® 2000: /all displays all the setting information related to TCP/IP. 3. To return to the Windows® screen, enter "exit" and press the "Enter" key. -56 - Sharp XG-P560W | XG-P560W Setup Manual - Page 57
Troubleshooting \ Check if the "TCP/IP" protocol is operating correctly using the " screen, enter "exit" and then press the "Enter" key. A connection cannot be made because you have forgotten your user name or your password. \ Initialize the settings. (See page 65 of the projector's operation manual - Sharp XG-P560W | XG-P560W Setup Manual - Page 58
Dimensions Units: inches (mm) Side View Rear View Top View Side View 25 3/32 (637) 13/64 19/64 (5) (7.5) 7 31/64 (190) (123.5) (91.5) 3 39/64 - Sharp XG-P560W | XG-P560W Setup Manual - Page 59
Dimensions Projector and Lens Dimensions [When AN-P8EX is installed] 2 /29 32 (73.6) 25 3/32 (637) Unit : inches (mm) [When AN-P18EZ is installed] /31 32 (24.5) 1/8 (2.8) 25 3/32 (637) Unit : inches (mm) Lens center 3 57/ 64 (98.5) Lens center (98.5) 57/ 64 3 [When AN-P12EX is
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
 |
 |
MODEL
XG-P560W
XG-P560W-N
DATA PROJECTOR
SETUP MANUAL
Setting up the Screen
..........................................
2
Screen Size and Projection Distance
................
3
Connecting Pin Assignments
..........................
11
Wired Remote Control Terminal Specifications
......
13
RS-232C Specifications and Commands
........
14
Setting up the Projector Network Environment
... 20
1. Connecting the Projector to a Computer
..........
21
2. Setting an IP Address for the Computer
..........
22
3.
Setting up a Network Connection for the Projector
... 24
Controlling the Projector via LAN
....................
26
Controlling the Projector Using Internet Explorer
(Version 5.0 or later)
...................................
26
Confirming the Projector Status (Status)
.............
27
Controlling the Projector (Control)
.......................
27
Setting and Adjusting the Projector
(Settings & Adjustments)
............................
28
Setting the Security (Network – Security)
............
28
Making General Settings for the Network
(Network – General)
...................................
29
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings)
........................
29
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ... 30
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL)
...........
30
Setting the Projector Using RS-232C or Telnet
... 31
When Connecting Using RS-232C
.......................
31
When Connecting Using Telnet
............................
32
SETUP MENU (Main Menu)
.................................
33
ADVANCED SETUP MENU
.................................
33
Controlling the Projector Using RS-232C or Telnet
... 34
View Setting Detail List ([V]View All Setting)
.......
34
Set Items
...............................................................
34
Save Settings and Quit ([S]Save & Quit)
.............
35
Quit without Saving Settings ([Q]Quit Unchanged)
... 35
IP Address Setting ([1]IP Address)
......................
36
Subnet Mask Setting ([2]Subnet Mask)
...............
36
Default Gateway Setting ([3]Default Gateway)
....
36
User Name Setting ([4]User Name)
.....................
36
Password Setting ([5]Password)
..........................
37
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate)
............................
37
Projector Name Setting ([7]Projector Name)
.......
37
DHCP Client Setting ([8]DHCP Client)
.................
37
Disconnecting All Connections
([D]Disconnect All)
.....................................
38
Entering ADVANCED SETUP MENU
([A]Advanced Setup)
..................................
38
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
.............
38
Data Port Setting (ADVANCED[2]Data Port)
.......
38
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test)
............
39
Setting of Accept IP Address (ADVANCED
[6]Accept IP Addr(1) – [8]Accept IP Addr(3)) ..
39
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
............
39
Setting of Search Port
(ADVANCED[0]Search Port)
......................
40
Return to Default Settings
(ADVANCED[!]Restore Default Setting)
.....
40
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
.......
40
Stack Projection
.................................................
41
Setting up the Stack Projection
............................
42
Video Wall Projection
........................................
44
Setting up the Video Wall Projection
Basic
.........
45
Adjusting the Position Horizontally and Vertically
... 47
Returning to the Default Video Wall Setup
...........
47
Assigning the Projected Image on the
Video Wall Setup
........................................
47
Notes on the Wide Video Wall Projection
.............
48
Setting up the Video Wall Projection
Application
.. 49
Resetting the Lamp Timer of the Projector via LAN
... 53
Troubleshooting
.................................................
55
Dimensions
........................................................
58