Sharp XG-SV100W Setup Manual
Sharp XG-SV100W Manual
 |
View all Sharp XG-SV100W manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp XG-SV100W manual content summary:
- Sharp XG-SV100W | Setup Manual - Page 1
be Sent when an Error Occurs (Mail - Recipient Settings 21 Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support - Access URL 21 Resetting the Lamp Timer of the Projector via LAN 22 Troubleshooting 24 - Sharp XG-SV100W | Setup Manual - Page 2
Connecting Pin Assignments COMPUTER/COMPONENT 1, 2 input and COMPUTER/COMPONENT output Terminals: mini D-sub 15 pin female connector 11 15 1 5 6 10 COMPUTER Input/Output Pin No. Signal 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. - Sharp XG-SV100W | Setup Manual - Page 3
CS CI Note • Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Projector Pin No. 4 5 6 Computer Pin No. 4 5 6 USB Terminal: Type B USB connector 43 Pin No. 1. 2. 3. 4. Signal VCC USB- USB+ SG Name USB power USB - Sharp XG-SV100W | Setup Manual - Page 4
type, commercially available) to the projector. (See page 25 of the projector's operation manual for connection.) Communication conditions Set the code (0DH) Problem response (communication error or incorrect command) ERR Return code (0DH) Info • When controlling the projector using RS-232C - Sharp XG-SV100W | Setup Manual - Page 5
projector, make the following setting. Computer P OWR _ _ _ 1 o m Projector OK Power Projector Condition Lamp M _ _ _ 1 XGSV100W/XGSV200X M N R D _ _ _ 1 XG-SV100W/XG-SV200X P J N 1 * * * * OK or ERR P J N 2 * * * * OK or ERR P J N 3 * * * * OK or ERR P J N 0 _ _ _ 1 Projector Name I R G B - Sharp XG-SV100W | Setup Manual - Page 6
16:9 Native Full Border (XG-SV200X only) Area Zoom V-Stretch Normal 16:9 Border (XG-SV200X only) Area Zoom V-Stretch Normal 16:9 Border (XG-SV200X only) Area Zoom V-Stretch Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp BrilliantColor™ DNR Picture Reset Signal Type Audio Input - Sharp XG-SV100W | Setup Manual - Page 7
Input Dynamic Range Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp BrilliantColor™ DNR Picture Reset Audio Input Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp BrilliantColor™ DNR Picture Reset Audio Input Standard Presentation Movie Game sRGB -30 - +30 -30 - +30 - Sharp XG-SV100W | Setup Manual - Page 8
RS-232C Specifications and Commands CONTROL CONTENTS Clock Phase H-position V-position Fine Sync Adjustment Reset Overscan OSD Display Video System Background Eco+Quiet Auto Sync Auto Power Off Auto Restart STANDBY Mode PRJ Mode Language -150 - +150 -30 - +30 -150 - + - Sharp XG-SV100W | Setup Manual - Page 9
Output". *4 This command can send only when the ceiling-mount rotating module (AN-SV100T: commercially available) is connected to the projector. *5 The Lamp Timer Reset command is available only in standby mode. *6 If the lens cover is not correctly attached, you may receive an "ERR" response - Sharp XG-SV100W | Setup Manual - Page 10
Number: 0: Lamp Off 1: Lamp on 1st Byte: Fan Error Status 2nd Byte: Lamp Error Status 3rd Byte: Temp. Error Status 4th Byte: Cover Open Status 5th Byte: Not Used, Return 0 6th Byte: Other Error Status 0: No Error Detected 1: Warning 2: Error Detected Projector Name SHARP XG-SV100W/XG-SV200X Not used - Sharp XG-SV100W | Setup Manual - Page 11
settings may need to be changed. Please consult your network administrator for assistance with these settings. You can make network settings both on the projector and on the computer. The following procedure is for making settings on the computer. Network settings on the computer 1. Connecting the - Sharp XG-SV100W | Setup Manual - Page 12
's LAN terminal and connect the other end of the cable to the computer's LAN terminal. 3 Plug the power cord into the AC socket of the projector. A LAN cable being connected to the network LAN cable (cross-over type, commercially available) 4 Turn on the computer. ON Info Confirm that the LINK - Sharp XG-SV100W | Setup Manual - Page 13
Setting up the Projector Network Environment 2. Setting an IP Address for the Computer and tasks" of "Network and Internet", and click "View status" in the new window. • This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click "Network - Sharp XG-SV100W | Setup Manual - Page 14
IP address, Subnet mask and Default gateway as you will be required to reset them later. 2 Set temporarily as follows: IP address: 192.168.150.3 (Do not input any values.) Note • The factory default settings for the projector are as follows: DHCP Client: OFF IP address: 192.168.150.2 Subnet mask - Sharp XG-SV100W | Setup Manual - Page 15
's IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. (See page 62 of the projector's operation manual for setting.) DHCP Client: Off IP Address: 192.168.150.002 Subnet Mask: 255.255.255.000 1 Start Internet Explorer (version 6.0 or - Sharp XG-SV100W | Setup Manual - Page 16
setting screen appears, ready for network settings for the projector. Items Setting example / Remarks New You can set having an IP address of "192.168.150.XXX", you don't have to change the projector IP address. • For details about each setting, consult your network administrator. 5 Click the - Sharp XG-SV100W | Setup Manual - Page 17
to external equipment before starting the operation. (See pages 22-26 of the projector's operation manual.) Complete the AC cord connection. (See page 26 of the projector's operation manual.) Note • When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category - Sharp XG-SV100W | Setup Manual - Page 18
can confirm the projector status. You can confirm the following items: • MAC Address • Power • Condition • Lamp Timer • Lamp Life • Input • For details about each item, refer to the projector's operation manual. On this screen, you can perform projector control. You can control the following items: - Sharp XG-SV100W | Setup Manual - Page 19
Select • DLP® LinkTM • DLP® LinkTM Invert • Rotate Indicator • All Reset Note • If you click the "Refresh" button before the screen is displayed completely this page while the projector is warming up. • For details about each item, refer to the projector's operation manual. On this screen, - Sharp XG-SV100W | Setup Manual - Page 20
/ Remarks Setting an SMTP server address for email transmission. e.g.1: 192.168.150.253 e.g.2: smtp123.sharp.co.jp * When using a domain name, make settings for the DNS server. Setting the projector's e-mail address. The e-mail address set here becomes Originator E-mail Address. Setting the sender - Sharp XG-SV100W | Setup Manual - Page 21
Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail - Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support - Access URL) On this screen, you can - Sharp XG-SV100W | Setup Manual - Page 22
Resetting the Lamp Timer of the Projector via LAN When the projector is connected to a network, you can use the communications program to send a command to reset the lamp If you do not have HyperTerminal installed, see the operation manual of your computer. • Depending on the settings of your - Sharp XG-SV100W | Setup Manual - Page 23
Properties window appears, click "OK". 8 If a user name and/or password is set for the projector, enter the user name and password. 9 Send the lamp reset command "LPRE0001". • This command can only be sent when the projector is in standby mode. • When "OK" is received, this indicates that the - Sharp XG-SV100W | Setup Manual - Page 24
Troubleshooting Communication cannot be established with the projector When connecting the projector using serial-connection ? Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly. ? Check that the RS-232C cable is a cross- - Sharp XG-SV100W | Setup Manual - Page 25
Troubleshooting ? Take the following steps for checking the network settings for the computer. 1. Open a command prompt. • In the case of Windows® 2000: click "start" ➔ "Programs" ➔ "Accessories" ➔ " - Sharp XG-SV100W | Setup Manual - Page 26
Troubleshooting ? Check if the "TCP/IP" protocol is operating correctly using the "PING" command. Also, check if an IP have forgotten your user name or your password. ? Initialize the settings. (See page 62 of the projector's operation manual.) ? After the initialization, carry out setting again. -26
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
MODEL
XG-SV100W
XG-SV200X
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments
............................................................
2
RS-232C Specifications and Commands
.........................................
4
Operating the Projector Using the PJLink
TM
Protocol
..................
10
Setting up the Projector Network Environment
...............................
11
1. Connecting the Projector to a Computer
............................................
12
2. Setting an IP Address for the Computer
.............................................
13
3. Setting up a Network Connection for the Projector
............................
15
Controlling the Projector via LAN
...................................................
17
Controlling the Projector Using Internet Explorer
....................................
17
Confirming the Projector Status (Status)
.................................................
18
Controlling the Projector (Control)
...........................................................
18
Setting and Adjusting the Projector (Settings & Adjustments)
................
19
Setting the Security (Network – Security)
................................................
19
Making General Settings for the Network (Network – General)
...............
20
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings)
............................................................
20
Setting Error Items and Destination Addresses to which E-mail is to be
Sent when an Error Occurs (Mail – Recipient Settings)
................
21
Setting Error Items and the URL that are to be Displayed
when an Error Occurs (Service & Support – Access URL)
............
21
Resetting the Lamp Timer of the Projector via LAN
.....................
22
Troubleshooting
................................................................................
24