Sharp XG-V10WLP Operation Manual

Sharp XG-V10WLP Manual

Get Sharp XG-V10WLP PDF manuals and user guides View all Sharp XG-V10WLP manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp XG-V10WLP manual content summary:

  • Sharp XG-V10WLP | Operation Manual - Page 1
    Sharp Projector(s) Network Configuration Operation Manual For The XG-V10WU XG-V10WM XG-V10XU XG-V10XM Sections: 1.) AN-L10T Optional Card Installation 2.) Projector Menu Configuration 3.) S.A.P.S. Software Configuration L:\tekcentr\CACTrain\SPS_ntwk 1 10/16/2001
  • Sharp XG-V10WLP | Operation Manual - Page 2
    What is a Network? A network is a group of computers, printers, projectors or other devices that are connected with cables or wirelessly (without cables). Information travels over the cables or through the airwaves, allowing network users to exchange documents and data with each other, print to the
  • Sharp XG-V10WLP | Operation Manual - Page 3
    When installing the expansion cards you must do the following: 1.) Shut projector Off. 2.) Remove the three screws from expansion plate cover. (Refer to Figure A) 3.) Remove (4) four screws that secure the RF shield (Refer to Figure B) NOTE: Number 2 - Only needs to be done if expansion slot is used
  • Sharp XG-V10WLP | Operation Manual - Page 4
    Expansion Slot with RF shield. FIG. B These (4) four screws secure shield. (Fig B) NOTE: The RF Shield only needs to be removed if expansion slot is used for first time. Expansion Slot Open (empty) Expansion Card Connector L:\tekcentr\CACTrain\SPS_ntwk FIG. C 4 10/16/2001
  • Sharp XG-V10WLP | Operation Manual - Page 5
    Projector Menu SetUp for the AN-L10T Optional Expansion Board The following "Projector Menu" functions need to be set in order to configure the projector to be used with the AN-L10T LAN card. 1.) ID Number Setup 2.) Optional Board (LAN Board) Setup 1.) To Setup the ID Number, proceed to the
  • Sharp XG-V10WLP | Operation Manual - Page 6
    There will be three items to configure thru the "LAN Board" menu option through the "Options 2" Menu. 1.) IP Address Set 2.) Gateway Set 3.) Subnet Mask 1.) The first option to be configured is "IP Address Set" When that option is selected, the following menu will appear. NOTE: The fields following
  • Sharp XG-V10WLP | Operation Manual - Page 7
    and the computers that serve pages to users are host nodes. The computers that control traffic within your company's network or at your local Internet service provider (ISP) are gateway nodes. NOTE: The "Gateway Set" address used is an example ONLY . This information is obtained through the IT / MIS
  • Sharp XG-V10WLP | Operation Manual - Page 8
    3.) The third option to be configured is "Subnet Mask" When that option is selected, the following menu will appear. NOTE: The fields following "SubNet Mask" will be blank if the LAN Card is used for first time. (For Example Only) NOTE: The "Subnet Mask" address used is an example ONLY . This
  • Sharp XG-V10WLP | Operation Manual - Page 9
    S.A.P.S Software V1.41 Network Configuration The steps below show how to configure the S.A.P.S. software for an existing Network. Launch the SAPS software, depending on how the software was originally configured, the menu when launched will be for either "Single" projector mode or "Multiple"
  • Sharp XG-V10WLP | Operation Manual - Page 10
    (Figure 3) Note: The projector must be in multiple projector mode in order to access the "Control Options" menu to continue with the network configuration involving the SAPS software. In Single Projector mode the Network control options menu items are inactive. (Refer to Figure 4) "Single Projector
  • Sharp XG-V10WLP | Operation Manual - Page 11
    Once the "Multiple Control" mode has been identified we can now proceed to the "Projector Setting " menu option under the "File" menu. (Refer to Figure 5) Figure 5 From the "Projector Setting" Mode we identify the "ID" Number which will be used by the projector. (Refer to Figure 6) This "ID" number
  • Sharp XG-V10WLP | Operation Manual - Page 12
    Figure 6 Under the "Projector" item select the proper projector XG-V10W / XU / M. Finally place a check in the "Use Projector" box. After confirming / adjusting the "Projector Setting" menu the "Apply" button will become active (Not ghosted) click the "apply" button and then the "OK" button and your
  • Sharp XG-V10WLP | Operation Manual - Page 13
    Proceed to the "Control Options" menu of the "Multiple Control" window There are four items which we will be interacting with on this menu option. 1.) Projector / Unique Name 2.) E-Mail Address Book 3.) Send E-mail Setting 4.) Sender setting (Refer to Figure 8) Figure 8 1.) The first item "
  • Sharp XG-V10WLP | Operation Manual - Page 14
    to 12 Characters Maximum. NOTE: the SAPS software can control up to 250 individual or grouped projectors. Please refer to your SAPS operation manual for further details on grouping projectors. Figure 10 After a "Projector / Unique Name" has been completed the changes will be reflected in the All
  • Sharp XG-V10WLP | Operation Manual - Page 15
    of using the SAPS software with the Networked V10 is status and diagnostics of the projector(s). The E-mail function e-mails your projector failure problems while also giving the E-mail recipients an overall status report. The Status report timing, when E-mail is sent out and what faults or
  • Sharp XG-V10WLP | Operation Manual - Page 16
    4.) The last item under the "Control Option" menu is "Sender Setting". (Refer to Figure 14) The SAPS software makes it possible to automatically send an e-mail message containing information concerning errors to a pre set e-mail address should projector errors be detected. The "E-mail Server (SMTP
  • Sharp XG-V10WLP | Operation Manual - Page 17
    Once identifying the "Scan Setting" menu option, the following screen appears. Depending on your projector setup and port configuration you must select what com ports to scan if any. For this example there are no other projectors connected so, no communication ports (com) need to be selected. If the
  • Sharp XG-V10WLP | Operation Manual - Page 18
    17) The green circle and the information indicated informs the SAPS administrator the unit is on and communicating. Please refer to the SAPS software manual for further information on these fields. If the projector is not detected with the scan setting the following screen will appear under the "All
  • Sharp XG-V10WLP | Operation Manual - Page 19
    Dynamic IP address Is a temporary IP address, which many Internet service providers use to limit the number of static IP addresses they allocate assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
XG-V10WU
XG-V10XU
XG-V10WM
XG-V10XM
Sections:
1.) AN-L10T Optional Card Installation
2.) Projector Menu Configuration
3.) S.A.P.S. Software Configuration
Sharp Projector(s) Network Configuration
Operation Manual
For The
L:\tekcentr\CACTrain\SPS_ntwk
1
10/16/2001