Sharp XV-Z7000U XV-Z7000U Operation Manual
Sharp XV-Z7000U Manual
 |
View all Sharp XV-Z7000U manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp XV-Z7000U manual content summary:
- Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 1
XV-Z7000U Serial No.: There are two important reasons for prompt warranty registration of your new SHARP LCD Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service (servicing) instructions - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 2
the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY Declaration of Conformity SHARP LCD PROJECTOR, MODEL XV-Z7000U This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 3
use and servicing. For your own protection and reliable usage of your LCD Projector, please be sure to read these "IMPORTANT SAFEGUARDS" carefully before use. 1. Read Instructions All the safety and operating instructions the outlet, contact your electrician to replace your obsolete outlet. Do not - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 4
converting the interlaced signal to the progressive. Useful for displaying slow-moving images or still SHARP Assistance (U.S.A. only) If you encounter any problems during setup or operation of this projector, first take a look at the section "Troubleshooting" on page 40. If this operation manual - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 5
Filter Maintenance 35 Lamp/Maintenance Indicators 37 Replacing the Projection Lamp 38 Using the Kensington Lock 40 Troubleshooting 40 Appendix Attaching the Lens Cap 41 Connection Pin Assignments 42 RS-232C Port Specifications 43 Computer Compatibility Chart 45 Specifications 46 Dimensions - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 6
the nearest Authorized SharpVision Service Center or Dealer replace lamp if rupture occurs. See "Replacing the Projection Lamp" on pages 38 and 39. CAUT I ON ATTENT I ON BQC-PGC20X //1 95˚F (ם35˚C) 41˚F (ם5˚C) Cautions Concerning the Setup of the Projector For minimal servicing and to maintain - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 7
in this manual where the topic is explained. Projector Front and Top View ON/OFF button 15 POWER indicator 15 16 INPUT/BACK button 20 KEYSTONE/Adjustment 19 (∂ /ƒ) buttons 20 ZOOM knob 15 ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU 37 LAMP REPLACEMENT indicator 37 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 8
compartment. properly seated. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • If you will not be using the remote control for a long time, remove the batteries. • Do not mix new and old or different types of batteries. • There are operations that - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 9
to prevent the remote control from skidding and shaking over a flat surface. Positioning the Remote Control The remote control can be used to control the projector within the ranges shown below. • The signal from the remote control can be reflected off a screen for easy operation. However, the - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 10
for remote control GLEGG9095CEZZ Power cord CACCU5013DE01 DIN-D-sub RS-232C cable QCNW-5288CEZZ Extra air filter PFILD0123CEZZ Lens cap PCOVZ1095CEKA Lens cap strap UBNDT0013CEZZ LCD projector operation manual TINS-7273CEZZ E-10 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 11
to the S-VIDEO INPUT terminal, or one end of the video cable to the OR VIDEO INPUT terminal on the projector and the video output terminal on the video source. 2 To use the built-in audio system, connect the RCA connectors to the corresponding AUDIO INPUT (S- VIDEO, VIDEO INPUT) terminals on - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 12
the one end of the D-sub/RCA cable to the INPUT 2 RGB/COMPONENT port on the projector. 2 Connect the other end of the cable to the corresponding terminals of a DVD player or DTV decoder. 3 To use the built-in audio system, connect one end of an audio cable to the AUDIO INPUT - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 13
the functions not to work. • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service Center or Dearler. When connecting this projector to a computer, select "RGB" by using RGB/COMPONENT on the remote control or the GUI menu. (See - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 14
, cross type, sold separately) DIN-D-sub RS-232C cable Projector RS-232C INPUT 1 /COMPONENT AUDIO INPUT Y PB PR manual of the computer for details on setting up. • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 15
for over one second, or POWER on the remote control. • The flashing green LAMP REPLACEMENT indicator shows that the lamp is warming up. Wait until the indicator stops flashing before operating the projector. • If the power is turned off and then immediately turned on again, it may take a short - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 16
is turned on, the POWER indicator and the LAMP REPLACEMENT indicator light green. • The POWER indicator flashes if projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the ON/ OFF button on the projector - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 17
and dim the lights when setting up the screen in a sunny or bright room. • A polarizing screen cannot be used with this projector. Standard Setup (Front Projection) Place the projector at the required distance from the screen according to the desired picture size. (See the table below.) FULL Mode - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 18
audience. Ceiling-mount Setup • It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. • Before mounting the projector, contact your nearest Authorized SharpVision Dealer or Servicer to obtain the recommended ceilingmount bracket and hardware (sold separately - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 19
can be made by pressing KEYSTONE, or by setting "Keystone" correction in the GUI menu. Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU Remote control Using the KEYSTONE buttons RGB/ INPUT 1 COMPONENT PICT MODE 1 Press KEYSTONE to adjust the setting. 1 INPUT - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 20
Using the GUI (Graphical User Interface) Menu Screens Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU 7 2, 4, 6 Remote control VOL POWER 3, 5 MUTE BACK MENU 1, 8 ENTER This projector has three sets of menu screens (INPUT 1 or 2 (COMPONENT), INPUT 2 (RGB) - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 21
Operation Using the GUI (Graphical User Interface) Menu Screens Items on the INPUT 1 or 2 (COMPONENT) Mode Menu Bar Main menu Picture1 Picture2 Options Language Sub menu Contrast Bright Red Blue Signal Type *1 Reset Color Tint Sharp Progressive *2 Reset Signal Info Lamp Timer - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 22
Operation Using the GUI (Graphical User Interface) Menu Screens Items on the S-VIDEO or VIDEO Mode Menu Bar Main menu Picture1 Picture2 Options Language Sub menu Contrast Bright Red Blue Reset Color Tint *3 Sharp Progressive Reset Signal Info Lamp Timer Keystone Auto Power Off - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 23
mode only) Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU Remote control VOL 2, 3 POWER 2, 4 1, 5 MUTE BACK MENU ENTER (GUI) On-screen Display The video input system mode is preset to "Auto"; however, it can be changed to a specific - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 24
projector's picture to your preferences with the following picture settings. Description of Adjustment Items Selected item Contrast Bright Red Blue Reset Color Tint Sharp ) mode, and then press ENTER. 3 Press ∂/ƒ to select a specific adjustment item, and then press ENTER. 4 Press ∂/ƒ to move the - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 25
setting. 6 To exit from the GUI, press MENU. Operation Projector Remote Control ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU 2, 3, 4 GUI, press MENU. Description of Progressive Modes 2D Progressive Useful for displaying fast-moving images such as sports and action - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 26
S-VIDEO CLR TEMP VIDEO KEYSTONE FREEZE 1 Auto Sync Adjustment • Used to automatically adjust a computer image. • Auto Sync adjustment can be made manually by pressing AUTO SYNC. • The sync adjustment is automatically made each time the projector is turned on while connected to a computer or the - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 27
26 for details. (Select the desired computer input mode with INPUT on the projector or INPUT 2 on the remote control.) 1 Press MENU. 2 Press ∂/ƒ to select "Fine Sync", and then press ENTER. 3 Press ∂/ƒ to select a specific adjustment item, and then press ENTER. 4 Press ∂/ƒ to move the mark of - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 28
PICT MODE INPUT 2 AUTO SYNC GAMMA S-VIDEO CLR TEMP VIDEO KEYSTONE FREEZE 1, 2 This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience. 1 Press FREEZE - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 29
GAMMA S-VIDEO CLR TEMP VIDEO KEYSTONE FREEZE 1 Position1 On-screen Display This function can be used to adjust the color temperature to suit the type of image input to the projector (video, computer image, TV broadcast, etc.). Decrease the color temperature to create warmer, reddish images - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 30
in a brightly lit room. 1 Press GAMMA on the remote control. Each time GAMMA is pressed, the gamma level toggles as shown on the left. s GAMMA 2 Useful Features E-30 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 31
Selecting the Picture Display Mode Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU Remote control RGB/ INPUT 1 COMPONENT PICT MODE INPUT 2 than a computer, the display is fixed in FULL (4:3) mode, with the image filling up the whole screen. Useful Features E-31 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 32
will be displayed. • It is recommended that the lamp be replaced after approximately 900 hours of usage. See pages 38 and 39 for lamp replacement. Useful Features Automatic Power Shutoff Function Projector Remote control ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 33
(4:3) mode even if another display mode has been selected. Theater Mode Function Projector Remote control ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU 2, 3, 4 2, 3 increase if internal temperature rises enough to activate the cooling function. Useful Features E-33 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 34
then press ENTER. 4 To exit from the GUI, press MENU. • This function is used for the reversed image and ceilingmount setups. See page 18 for these setups. Special Mode Adjustment Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU Remote control VOL 2, 3 POWER - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 35
. • The air filter should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location. • Have your nearest Authorized SharpVision Service Center or Dealer exchange the filter (PFILD0123CEZZ) when it is no longer possible to clean it - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 36
over the projector. Press the tab and remove the filter cover in the direction of the arrow. 1 Remove the air filter stopper. 2 Remove the air filter. Tab 4 Replace the air position. 2 Put the air filter stopper back into position. 5 Replace the filter cover. Insert the tab on the end of the - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 37
stops flashing and turns off. • Carefully replace the lamp. (See pages 38 and 39.) • Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair. • Securely install the filter cover. Maintenance & Troubleshooting • If the TEMPERATURE WARNING indicator illuminates - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 38
Center or Dealer. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer. IMPORTANT NOTE TO U.S. CUSTOMERS: The lamp included with this projector is backed by a 90-day parts and - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 39
of the arrow. Then tighten the user service screw. Maintenance & Troubleshooting Resetting the lamp timer 1 Connect the power cord. Plug the power cord into the AC socket of the projector. 2 Reset the lamp timer. 1 Press KEYSTONE ∂ and KEYSTONE ƒ on the projector at the same time. 2 Press INPUT - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 40
system for instructions on how to use it to secure the projector. Troubleshooting Problem Check No picture and no sound. • Projector power cord operation or performance. Maintenance indicator illuminates. • Refer to "Lamp/Maintenance Indicators" on page 37. Picture noise appears. • Adjust - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 41
the lens cap to the projector with the lens cap eyelet facing up. CAUTION • Do not lift or carry the projector by the lens or the lens cap as this may damage the lens. • You can also use the end of a mechanical pencil or other pointed object to feed the lens cap strap - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 42
Connection Pin Assignments INPUT 2 Port: 15-pin mini D-sub female connector Computer Input Analog 1. Video input (red) 2. Video input (green/sync on green) 5 1 3. Video input (blue) 10 6 4. Not connected 15 11 5. Composite sync 6. GND (red) 7. GND (green/sync on green) 8. GND (blue - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 43
Specifications PC control A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, sold separately) to the projector Normal response Parameter 4-digits O K Return code (0DH) Problem response (Failure due to incorrect command/parameter or the other - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 44
Specifications Commands EXAMPLE • When "BRIGHT" of RGB IMAGE ADJUSTMENT is set to מ10. Computer RABR _מ1 0 → ← Projector * * TINT (מ30 - ם30) V A S H _ _ _ * SHARPNESS (0 - 7) V A R E _ _ _ 2 RESET S-VIDEO/VIDEO COLOR TEMPERATURE ADJUSTMENT V AC T ___ COLOR TEMPERATURE * (1- 4) R - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 45
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in "CRT only" mode. Details on how to change display modes can be found in your notebook computer's operation manual. • This projector can receive 640 ן350 VESA format VGA signals, however, "640 - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 46
Specifications Product type LCD Projector Model XV-Z7000U Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I Display method LCD panel ן3, RGB optical shutter method LCD cap strap, LCD projector operation manual Replacement parts Lamp unit (Lamp/cage module) - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 47
21/32 (42) 1 17/64 (32) 3 15/64 (82) Side View 10 15/64 (260) 8 5/32 (207) 6 43/64 (169.5) FOCUS ZOOM ON/OFF POWER LAMP TEMP. KEYSTONE INPUT PICT MODE BACK ENTER MENU S-VIDEO INPUT VIDEO INPUT AUDIO INPUT (S-VIDEO, VIDEO INPUT) L R Top View RS-232C INPUT 1 /COMPONENT AUDIO INPUT - Sharp XV-Z7000U | XV-Z7000U Operation Manual - Page 48
for displaying slow-moving images or still images. RS-232C Function to control the projector from the computer by using the RS-232C ports on the projector and computer. Sync on green Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin. Theater
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
E-1
Important
Information
IMPORTANT
For your assistance in reporting the loss or theft of your
Color LCD Projector, please record the Serial Number
located on the bottom of the projector and retain this
information. Before recycling the packaging, please be
sure that you have checked the contents of the carton
thoroughly against the list of “Supplied Accessories”
on page 10.
Before using the LCD projector, please read this operation manual carefully.
OPERATION MANUAL
ENGLISH
Model No.: XV
-
Z7000U
Serial No.:
There are two important reasons for prompt warranty registration of your new SHARP LCD Projector,
using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2.
CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Rules.
WARNING:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“
dangerous voltage
”
within the product
’
s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
ENGLISH
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and high intensity discharge lamp (HID lamp) containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org .