Sharp XV-Z90U XV-Z90U Operation Manual
Sharp XV-Z90U Manual
 |
View all Sharp XV-Z90U manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp XV-Z90U manual content summary:
- Sharp XV-Z90U | XV-Z90U Operation Manual - Page 1
PROJECTOR PROJECTEUR PROYECTOR PROJETOR XV-Z90U OPERATION MANUAL MODE D'EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO ESPAÑOL PORTUGUÊS FRANÇAIS ENGLISH - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 2
page 11. Model No.: XV-Z90U Serial No.: There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 3
COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XVZ90+++1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING. MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 4
the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the distinct change in performance. 19. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 5
rupture, contact your nearest Authorized SharpVision Service Center or Dealer for a replacement. See "Replacing the Lamp" on page 46. CAUTION PRECAUCIÓN PRÉCAUTION BQC-XVZ90+++1 This caution is found at the bottom of the projector. See "Caution Concerning the Lamp Replacement" on page 2 for its - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 6
change during projector operation due to changes in the fan speed. Lamp Monitor Function When the projector is turned on after the lamp has been used for 2,400 hours, "LAMP" and " " will blink in the lower-left corner of the picture to advise you to replace the lamp. See page 46 for lamp replacement - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 7
mount Video Signal (VIDEO Lamp Maintenance 45 Confirming the Lamp Usage Time 45 Replacing the Lamp 46 Cleaning the Ventilative Holes 49 Using the Kensington Lock 50 Troubleshooting 50 For SHARP Assistance (U.S.A. only) ..... 50 Appendix Connecting Pin Assignments 51 (RS-232C) Specifications - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 8
Digital Light Processing, DLP, Digital Micromirror Device similar video system. 9. Easy-to-use Graphical User Interface projector by pressing the PICTURE SETTING button on the projector or on the remote control. 13. Component Video Input Utilizes a component video input signal (Y, PB, PR). The video - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 9
refer to the main pages in this manual where the topic is explained. Projector Front and Top View Lens shift dial 18 Zoom knob 16 Exhaust ventilative hole 4 Focus ring 16 Remote control sensor 15 5 TEMPERATURE WARNING indicator 5 LAMP REPLACEMENT indicator 16 POWER indicator 4 Exhaust ventilative - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 10
to the part names refer to the main pages in this manual where the topic is explained. Projector Side and Rear View Remote control sensor 15 Intake ventilative hole 49 49 Intake ventilative hole INPUT 2 DVI digital port 13 INPUT 3 S-VIDEO terminal 13 (4-pin Mini DIN) 14 RS-232C port (9-pin - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 11
Important Information Part Names Remote Control POWER buttons (ON/OFF) 16 KEYSTONE button 19 ENTER button 19 UNDO button 26 INPUT 1 button 24 INPUT 2 button 24 INPUT 4 button 24 AUTO SYNC button 35 RGB/COMP. button 36 Front View Top View 26 MENU button 19 ADJUSTMENT buttons 24 INPUT 3 button - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 12
Important Information Supplied Accessories Remote control RRMCGA064WJSA Two AA size batteries Power cord QACCDA007WJPZ Terminal cover GCOVAA116WJKA Lens cap CCAPHA004WJ01 Lens cap strap UBNDT0013CEZZ Operation manual TINS-A286WJZZ Screws for terminal cover XBBSN40P10000 E-11 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 13
cable (commercially available) to the INPUT 4 VIDEO terminal on the projector. 2 Connect the other end of the S-video cable or the video cable to the S-video output or Video output terminal of the video source. The S-video input terminal uses a video signal system where the picture is separated into - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 14
or press RGB/COMP. on the remote control. (See page 36.) CAUTION • Make sure to turn both the projector and the video equipment off, before switching the "DIGITAL INPUT TYPE" swich and connecting. Projector E-13 DVI to 15-pin D-sub adaptor (sold separately AN-A1DV) 3 RCA to 15-pin D-sub cable - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 15
RGB/COMP. on the remote control. (See page 36.) CAUTION • Make sure to turn both the projector and the video equipment off, before switching the "DIGITAL INPUT TYPE" swich and connecting. Projector DVI to 15-pin D-sub adaptor (sold separately AN-A1DV) DTV decoder Connecting to a Computer When - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 16
on a computer. • Make sure to turn both the projector and the video equipment off, before switching the "DIGITAL INPUT TYPE" swich SharpVision Service Center or Dealer. Operating the Remote Control Remote Control 23Ј (7 m) 30˚ 45˚ 30˚ The remote control can be used to control the projector - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 17
Setup & Connections Power ON/OFF POWER buttons TEMP. LAMP POWER Press POWER ON. • The blinking green LAMP REPLACEMENT indicator shows that the lamp is warming up. Wait until the indicator stops blinking before operating the projector. • If the power is turned off and then immediately turned on - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 18
Unlock the lever on the Swivel Stand. 2 Adjust the angle and direction of the projected image as you want by lifting up the projector and rotating the projector on the Swivel 2 Stand. 3 Lock the lever on the Swivel Stand. Adjustable up to ± 10° from the stadard position. Adjustable up to ± 25 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 19
Using the Lens Shift The picture can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the projector using your finger. Projector Projected Image Lens shift dial UP DOWN UP DOWN Setup & Connections E-18 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 20
of 2D Keystone Correction Selected item H Keystone V Keystone Reset Description Horizontally adjusts the keystone settings. Vertically adjusts the Horizontal Keystone Correction Vertical Keystone Correction E-19 1 Press KEYSTONE on the projector or on the remote control. 2 Press / to select "H - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 21
until the image on the screen becomes clear. (See page 16.) 2 Change the projection angle using the Swivel Stand to properly project images onto the screen (See page 17). 3 Align the edge of the screen closest to the projector with the test pattern by adjusting the zoom and the Swivel Stand. (See - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 22
(See the diagram [fig. 1] above.) When using a wide screen (16:9) 16 9 : Picture area : Area covered by the projection panel of the projector* Screen size (16:9) Projection distance and Keystone correction Diag. (x) Width Height Maximum (y1) Maximum horizontal placement range (h) 200" 174" 98 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 23
90° Lower edge of screen (White portion) = Standard (0) point Lower lens shift position (Desktop setup) Upper and Lower Lens Shift Position (Ceiling Mount) When the projector is in the inverted position, use the upper edge of the screen as the base line, and exchange the lower and upper lens shift - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 24
that you use the optional Sharp ceiling-mount bracket for this installation. • Before mounting the projector, remove the Swivel Stand. (See page 17 for removing and attaching the Swivel Stand.) • Before mounting the projector, contact your nearest Authorized SharpVision Service Center or Dealer to - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 25
button • When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG." will be displayed. On-screen Display INPUT 1 Press RESIZE. Each time RESIZE is pressed, the picture mode changes as shown on the next page. 1 E-24 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 26
Operation Buttons Adjusting the Picture Aspect Ratio DVD / VIDEO Imput Signal COMPUTER Imge Type NORMAL Projects the image fully on a screen while maintaining the aspect ratio. Output screen image BORDER STRETCH Projects the image - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 27
3 or 4 (VIDEO) mode 1 2 3 3 Basic Operation 4 1 Press MENU. The "Picture" menu screen for the selected INPUT mode appears. 2 Press / to display the other menu screen, if you want. The icon for the selected menu screen will be highlighted. 3 Press / to select a specific adjustment item - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 28
מ30 ם30 Tint מ30 ם30 Sharp מ30 ם30 Red מ30 ם30 Blue מ30 ם30 Reset CLR Temp 5500k 6500k 7500k 8500k PRJ V-Pos מ30 ם30 Reset Special Modes Auto Sync [ON/OFF] Signal Info Digital Shift מ30 ם30 * Subtitle מ10 ם10 Reset Lamp Timer OSD Display [ON/ - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 29
Menu Bar Main menu Sub menu Main menu Picture ( ) Options ( ) Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp מ30 ם30 מ30 ם30 מ30 ם30 מ30 ם30 מ30 ם30 ם30 Subtitle מ10 ם10 Reset Lamp Timer OSD Display [ON/OFF] Video Systems Background Auto Power Off [ - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 30
Display e. g. (VIDEO input in INPUT 3 or 4 mode) 1 2 You can adjust the projector's picture to your Sharp Red Blue CLR Temp Gamma White Emphasis Picture Setting Reset The "Picture" menu screen appears. 2 Press / to select a specific adjustment item. 3 Press / to move the mark of the selected - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 31
Adjusting the Picture 4 2, 3 1, 5 On-screen Display 2, 3 1, 4 On-screen Display Adjusting the Color Temperature This function allows for selecting the desired color temperature from six settings. With the lower value selected, the projected image becomes warmer, reddish and incandescent-like - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 32
Adjusting the Picture 4 2, 3 1, 5 On-screen Display Standard Black Detail Brighten White Detail Gamma Correction Function Gamma is an image quality enhancement function. Four gamma settings are available to allow for differences in the brightness of the room. Description of Gamma Modes - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 33
(INPUT 1 to INPUT 4 and DIGITAL). Even when the input mode or signal is changed, you can easily select optimal settings from the stored settings. • This function can be operated using the PICTURE SETTING button on the projector or on the remote control, as well as the OSD menu screen. Description - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 34
/ to display the "Fine Sync" menu screen. 3 Press / to select a specific adjustment item. 4 Press / to move the mark of the selected adjustment item to reset all adjustment items, select "Reset" on the "Fine Sync" menu screen and press ENTER. • The adjustable area of each item may be changed - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 35
Adjusting the Computer and DVD/DTV Images 2,3,4 1, 6 5 On-screen Display Special Modes Adjustment Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 36
MENU. • When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 33.) • The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. • "Auto Sync" cannot be used in the digital mode. AUTO - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 37
Turning On/Off the On-screen Display 2,3,4 1, 5 On-screen Display This function allows you to turn on or off the on-screen messages that appear during input select. Description of OSD Display Selected item ON ( ) OFF ( ) Description All On-screen Display are displayed. INPUT is not displayed. 1 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 38
1, 6 5 On-screen Display The video input system mode is preset to "Auto"; however, it can be changed to a specific system mode if the selected system mode to select the image displayed when no signal is being sent to the projector. Description of Background Images Selected item Blue ( ) None ( ) - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 39
can adjust settings according to the position and size of the screen. Description of Adjustment Items Selected item Description Digital Shift Subtitle Reset Adjusts the vertical position of the image. Adjusts the vertical size of the image. Digital Shift and Subtitle adjustments are returned to - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 40
setting. 5 To exit the menu screen, press MENU. • When changing the screen with the Subtitle setting, not only the bottom of the screen rises, but also the upper part is changed to a certain point. • The subtitle setting can be adjusted more - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 41
Selecting the Menu Screen Position 2,3,4 1,6 5 On-screen Display This function allows you to select the desired position of the menu screen. Description of Menu Position Selected item Description Center The menu is displayed on the center of the image. Upper Right The menu is displayed on - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 42
Automatic Power Shut-off Function 2,3,4 1, 5 When no input signal is detected for more than 15 minutes, the projector will automatically shut off. The on-screen message on the left will appear five minutes before the power is automatically turned off. Description of Automatic - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 43
2,3 4 1, 5 On-screen Display This projector is equipped with a reverse/invert image function which screen Display English is the preset language for the On-screen Display; however, this can be changed to German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 44
pressed in the order shown below. - --- -- 2 Press / to select a specific adjustment item. 3 Press / to move the mark of the selected adjustment item to setting. 4 To exit the menu screen, press MENU. • To reset all adjustment items, "Reset" in the "Picture" menu screen and press ENTER. • Advanced - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 45
: a TEMPERATURE WARNING indicator that warns you when the projector is too hot, and a LAMP REPLACEMENT indicator that warns you when to change the lamp. • If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT indicator will illuminate in red. After turning off the - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 46
off. Problem • Lamp has been used for over 2,400 hours. • Lamp has been used for over 2,500 hours. E-45 Possible Solution • Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-XVZ90+++1 from your nearest Authorized SharpVision Service Center or Dealer. • Replace the lamp - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 47
projector to the nearest Authorized SharpVision Service Center or Dealer for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-XVZ90+++1 from your nearest Authorized SharpVision Service Center or Dealer. Then carefully change the lamp by following the instructions - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 48
. of the arrow. 6 Loosen and remove the three-securing screws from the lamp cage. User service screws 7 8 9 Remove the lamp cage. Insert the new lamp cage firmly into the lamp cage Tighten the threesecuring screws to compartment. fasten the lamp cage. Maintenance & Troubleshooting E-47 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 49
the user service screw to fasten Plug the power cord. the lamp cage cover. 13 Press POWER ON on the projector to reset the lamp timer. Press , , , , order. Then press . and in "LAMP 0000H" is displayed on the screen. • You need to reset the lamp timer every time you replace the lamp and - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 50
ventilative holes should be cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location. Side and Rear view How to clean the ventilative holes holes Swivel stand Intake ventilative holes Maintenance & Troubleshooting E-49 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 51
(no green) on INPUT 2 RGB. • Change the input signal type. (See page 36.) For SHARP Assistance (U.S.A. only) If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on this page. If this operation manual does not answer your question - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 52
Connecting Pin Assignments DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector 9 ~ 16 1 2 7 8 17 24 18 23 • DVI Digital INPUT Pin No. Signal Pin No. Signal 1 T.M.D.S data 2- 16 Hot plug detection 2 T.M.D.S data 2+ 17 T.M.D.S data 0- 3 T.M.D.S data 2 shield 18 T.M.D.S data 0+ 4 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 53
Specifications and Command Settings PC control A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, commercially available) to the projector Parameter 4-digits O K Return code (0DH) Problem response (communication error or incorrect command) E R - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 54
(RS-232C) Specifications and Command Settings BUTTONS & REMOTE CONTROL KEY CONTROL CONTENTS POWER ON POWER OFF INPUT 1 (COMPONENT 1) INPUT 2 (COMPONENT 2) INPUT 3 (S-VIDEO) INPUT 4 (VIDEO) DIGITAL MODE COMMAND PARAMETER RETURN P O W R _ _ _ 1 OK OR ERR P O W R _ _ _ 0 OK OR ERR I V E D _ _ _ - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 55
SVGA 832 ן624 49.6 75 DVI Support Display Upscale Ture ✔ ✔ Intelligent Compression Upscale Intelligent Compression Appendix • This projector may not be able to display images from . Details on how to change display modes can be found in your notebook computer's operation manual. E-54 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 56
Dimensions Rear View Side View Top View Side View (327) 7/ 8 1 2 (153.8) 4 5 /8 (118) Front View Bottom View 14 /1 2 (368) E-55 6 9/ 1 6 Units: inches (mm) Appendix - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 57
Specifications Product type Projector Model XV-Z90U Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480i/480P/720P/1080i Display method DLP chip, RGB optical shutter method DLP manual, Screws for terminal cover Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ90+++1), - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 58
the color temperature to suit the type of image input to the projector. Decrease the color temperature to create warmer, reddish images for natural or STRETCH of COMPUTER, VIDEO and DTV inputs. DVI (Digital Visual Interface) Display digital interface that also supports Analog interfaces. GAMMA - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 59
mount 22 Clock 33 COMPONENT terminals 13 D Digital shift 38 DVI 14 E ENTER button 19 Exhaust ventilative hole 4 F Focus ring 16 H HDCP 7 I INPUT buttons 24 K Kensington Lock 50 KEYSTONE button 19 L LAMP REPLACEMENT 24 Subtitle 39 S-VIDEO INPUT terminal 12 Sync 35 Sync on green 54 - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 60
Specific Section (In-Home Service) Your Product Model Number & Description: XV-Z90U Projector (Be sure to have this information available when you need service for your Product.) Warranty Period for this Product: One (1) year parts and labor from date of purchase except for the Projector Lamp - Sharp XV-Z90U | XV-Z90U Operation Manual - Page 61
contract, negligence, strict liability or otherwise. WARRANTY PERIODS Projector 1 years (bulb 90 days) To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact: SHARP ELECTRONICS OF CANADA LTD. SHARP ELECTRONICS OF CANADA LTD 335 Britannia Road East
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
 |
 |
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACION
MANUAL DE OPERAÇÃO
XV
-
Z90U
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS