Sony DWM02/30 Product Information Document (Digirtal Wireless System Integrati
Sony DWM02/30 Manual
View all Sony DWM02/30 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sony DWM02/30 manual content summary:
- Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 1
Digital Wireless Microphone System System Integration Guide - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 2
Checking the Service Area With One Channel 51 Step 4 Checking Third-order Intermodulation Distortion 52 Step 5 Checking Simultaneous Multi-channel Operation 53 Troubleshooting 55 Configuration (82 channels 76 References 77 List of Supported Frequencies 77 Equipment Specifications 78 2 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 3
improved sound quality. In response to these important requirements, Sony continues to strive to develop a digital audio wireless transmission technology with a bundled camcorder to full-fledged studio/concert systems supporting simultaneous multi-channel operation. This provides users with the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 4
B01 Digital Wireless Transmitter WiDIF-HP Wireless transmission UHF Accessories (Option) AN-01 UHF Antenna WD-850 UHF Antenna Divider BNC Cable LAN Cable DWX Receiver Series DWR-R01D Digital Wireless Receiver DWR-S01D Digital Wireless Receiver DWX Adapter DWT-P01 Digital Wireless Transmitter AN - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 5
by Sony. It enables highly secure transmission with high sound quality and low system latency, and supports simultaneous or better 192 kHz or less π/4 Shift QPSK 3.4 milliseconds ** ** When DWM-01, DWT-B01, and DWR-R01D are used in combination. When analog output is combined with the DWR-S01D - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 6
regardless of receiver location. The service area range is about 10 meters from the control unit. Configuration for NT mode RMU-01 DWM-01 Control Data on 2.4GHz DWT-B01 Ethernet Hub LAN Cable Stage be useful, for example, in identifying the cause of reception problems. 6 What Is Cross Remote? - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 7
Technology Technology WiDIF-HP Technology A new high-profile format for the digital audio interface on UHF - WiDIF-HP -- has been developed for the DWX series. This section provides further details on WiDIF-HP technology. WiDIF-HP Technology Outline A digital audio wireless transmission system - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 8
is characterized by the following key features. Outstanding sound quality with 24-bit/48-kHz sampling Low latency Secure transmission The Sony digital audio codec achieves an optimum balance between sound quality, bit rate, and latency, while having the redundant bit assignment necessary for - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 9
CODEC 24 bit RF Digital De-modulator Data Audio Data Channel Decoding Up Sampling & Bit Expansion @48-kHz fs 1152 kb/s D/A AF Sony has developed a new digital modulator and demodulator that allows large-scale simultaneous multichannel operations. In addition to benefiting from advanced RF - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 10
WiDIF-HP technology was developed by Sony to fundamentally improve the transient response WiDIF-HP provides a fundamental solution to this problem and further enhances sound quality by realizing a Wireless Microphone DWM-01, Digital Wireless Transmitter DWT-B01, and Digital Wireless Receiver DWR-R01D. - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 11
are no errors, the audio signal quality will not be degraded. In the Sony digital wireless system, an error does not occur provided the D/U signal ratio Undesired Spectrum Spectrum * D/U ratio: Desired/Undesired ratio The Sony DWX series of digital wireless microphones employing the WiDIF-HP - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 12
Typically, analog systems require a D/U signal ratio of 40 dB or more. In the Sony digital wireless system on the other hand, an error does not occur provided the D/U signal or more, and is therefore much less prone to problems caused by intermodulation and is more efficient in handling frequencies - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 13
Technology Common Frequency Reuse Configuration In a digital wireless system, the minimum distance for reusing a common frequency is one sixth of an analog setup. Compared to an analog system or a mixed analog/digital system, the digital wireless system can be configured for a three times bigger - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 14
maintain confidentiality for conference rooms, live performance venues and other applications where strong measures against interception are required. The Sony digital system offers the choice between a secure mode using encryption keys, and a password mode where a secure group comprising multiple - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 15
indication RF level meter Model name Input level Attenuator level Transmission battery indication Example for transmitted information (with DWT-B01) Transmitter name Battery status RF power setting Attenuator level setting Low-cut filter setting Continuous operation time Using - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 16
and shotgun microphones with a suffix /9X in the model name, such as the ECM-77BC/9X, are certified by Sony to be suitable for use with the DWX digital wireless system. Other Sony professional microphones without a /9X in the model name may not be suitable for use with the DWX system. Microphones - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 17
based on application requirements and an evaluation of characteristics at the service area limit. Because WiDIF-HP is tuned to maintain voice much as possible even when errors occur, evaluation of error rates within the service area should be done using the Quality Level (QL) meter on the display - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 18
channel spacing applies only to fully digital wireless systems. Equal channel spacing is not available for analog wireless systems. Notes Refer to Sony digital wireless system frequency lists for further details on pre-programmed groups of frequencies built into every DWX transmitter and receiver - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 19
Technology System Behavior in Case of Interference To understand how analog and digital systems can have a mutual effect on each other in actual operation, it is important to consider the way in which the demodulated audio signal deteriorates when interference occurs. Analog Analog The stronger - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 20
DWT-B01 Metadata transmitted via WiDIF-HP Status information for each transmitter is sent on respective UHF frequency If metadata monitor function only is used, service system management PC Up to 6 Windows PCs are supported *When using the DWR-S01D as receiver, the RMU-01 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 21
wireless communication standard for domestic appliances. It uses the physical layer interface defined by the IEEE 802.15.4 and newly defines the network layer, security service provider, and application layer. ZigBee is not identical with IEEE 802.15.4. Cross Remote Technology 21 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 22
Technology System configuration APL Layer MAC Layer PHY Layer Application Layer: Defines the protocols for user interaction on the network (pairing and address allocation). Media Access Layer: Defines the specifications for device interaction on the network (error correction, ACK, resend request - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 23
Technology Used frequencies Cross Remote selects the optimal frequency for communication based on the system and the environment. If interference is detected on a currently used frequency, the system automatically switches to another frequency and continues communication. This assures stable - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 24
to identify devices by frequency assignment, as for the main communication link. As the control signal reaches all transmitters within the service area, pairing is necessary to establish which receiver is operating which transmitter. Control of transmitter A is intended, but signals also reach - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 25
to that remote control unit, and the connection to the paired receiver is established again. This process is called roaming. The Cross Remote service area can be enlarged by using multiple remote control units and maintaining communication through roaming. Roaming in NT mode Receiver RMU-01 NG - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 26
Features In ST mode, the transmitter and receiver communicate directly in a one-on-one configuration. When the receiver is placed within a main link service area, Cross Remote can be used within a range of about 10 meters from the receiver. Note Because the number of channels will increase when - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 27
Technology NT Mode Features In NT mode, transmitters and receivers communicate via the Remote Control Unit RMU-01 connected to a network. This enhances convenience during simultaneous multi-channel operation. In ST mode, a paired receiver and transmitter operate in a one-on-one configuration. This - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 28
Technology Communication flow from Wireless Studio Computer used for monitoring All commands must pass through receiver Send command via Ethernet Hub RMU-01 Transmit control command via 2.4 GHz band Transmitter Show transmitter information Send status ATT 0 dB information via - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 29
can be saved in a setup file and recalled later. Note Wireless Studio identifies the DWR-R01D and RMU-01 by IP address. The DWM-01/DWT-B01 are mutually identified by the DWR-R01D and MAC address. In order to allow later reloading and 100% restoring of setting information saved in Wireless - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 30
to ensure that the main (UHF) link and remote control (2.4 GHz) link wireless signals will not be interrupted in the Cross Remote service area. When installing main link equipment including antenna, receiver, and remote control unit, the possibility of interference from other equipment should be - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 31
a system and provides information about limitations, frequency support and other aspects. System Sections and Configuration Flow System Wireless Microphone DWX Transmitter Series DWT-B01 Digital Wireless Transmitter WiDIF-HP Wireless transmission DWT-P01 Digital Wireless Transmitter 2. - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 32
B band (4 MHz) Within A-B band (40 MHz) 2 diversity inputs Using DWR-R01D cascade connection, one WD-850 supports up to 64 channels Combination of 2 cascaded WD-850 units and DWRR01D cascade connection supports up to 128 channels Maximum is 82 regardless of number of RMU-01 units Maximum is 42 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 33
Configuring a DWX System Audio Equipment Selection When selecting equipment for a DWX series system, please take the features and specifications of the respective models into consideration. Equipment Features DWX series equipment is divided into the following categories. DWX Microphone Series - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 34
DWX System DWX Transmitter Series DWT-B01/E Digital Wireless Transmitter Compact and lightweight transmitter suitable for a wide range of input levels, from microphone level to line audio level. DWT-P01 Digital Wireless Transmitter The DWT-P01 is a plug-on transmitter that supports a wide range of - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 35
AC IN connector For connection of the supplied AC power cable. ANTENNA a/b OUT (Antenna a/b output) connectors (BNC-R) DWR-R01D can be connected to a and b, with support for cascading of up to 8 units. REM ANT (ST mode system antenna) For connection of an external antenna for the ST mode system - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 36
a single cable. Channel 1 can be analog, even if channel 2 is used as digital output. (Analog UHF Synthesizer Tuner Unit WRR-855S is also supported, but the AES/EBU digital output and analog output in channel 2 cannot be used.) Front Monitor output selector Selects the audio output from - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 37
. The DWR-R01D is supplied with two whip antennas. If the service area is small, you can also use the supplied whip antennas, but RMU-01 control and Wireless Studio combined monitoring capability, the DWX system supports a maximum of 82 channels in a networked configuration. If not configured - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 38
Configuring a DWX System Equipment Features UHF Accessories UHF Antenna AN-01 This is a unidirectional log periodic dipole antenna. Example of horizontal directivity characteristics Built-in low noise and low distortion booster amplifier with three gain settings: 18 dB/10 dB/0 dB. Booster - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 39
the tuner. ANTENNA B IN / DC OUT 1 and 2 (antenna B input/DC power output 1 and 2) connectors When connected by coaxial cable, the signal is input from the Sony UHF antenna while power is supplied to the antenna's booster amplifier. The power supply can be set to 9V or OFF using the ANTENNA B DC - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 40
- 9 V/12 V*3 9 V/12 V*3*4 9 V - 12 V Voltage selection method Switch None (Auto) - Support gain/attenuator 0 dB/-5 dB/-10 dB*5 0 dB/-5 dB/-10 dB 0 dB 0 dB/10 dB/18 dB ohms. Both for analog wireless systems and digital wireless systems, Sony recommends "5D-2V" -- "8D-2V" cables with 50-ohm - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 41
Configuring a DWX System Number of antennas and diversity reception Use two identical antennas The DWX system, like the conventional analog wireless system, uses the space diversity reception principle. Two antennas are employed to receive the signal, with the system automatically switching to the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 42
of at least 2 to 3 meters between transmitter and antennas should always be maintained. If the transmitter and antenna are too far apart, the service area will become doughnut-shaped. Installation should allow direct line of sight from transmitter to antenna There should be no obstacles between the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 43
intended only to cover cable losses. High gain settings exceeding the cable loss compensation requirements may actually result in a smaller service area during simultaneous multichannel operation, due to increased intermodulation. For example, when antenna input level is raised, the range from - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 44
Band usage: White space TV channel 2. Group usage: See "List of Supported Frequencies" (page 78) 3. Antenna installation location/orientation: distance to TX, on number of antennas and gain settings. Step 3 Checking the service area with one channel Using the desired channel only, assign a - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 45
of Wireless Studio. See the next section for details. Checking with the DWR-R01D display You can check whether the transmitter is in the service area by using the display of the Digital Wireless Receiver DWR-R01D. RF level meters QL meter Configuring a DWX System RF indicator RF (radio - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 46
installation location/orientation: Install according to requirements described in "Antenna installation position" (page 43). Antenna gain: Set according to instructions in "Booster gain setting conditions" (page 44), ensuring that cable losses can be fully covered. Number of antennas: Determine - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 47
System 4 If there is interference noise that could become a problem, change the channel plan perform the checking procedure again. the group. For details on the groups that can be selected, see "Sony Digital Wireless Microphone System Frequency Lists" (PDF). *When simultaneous multi-channel - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 48
on number of antennas and gain settings. Procedure Selecting the desired channel 5 Power up all TX except one, and position the TX within the envisioned service area at the location closes to the antenna. Example: In a 12-channel system, turn one TX off and turn the eleven other TX on. * Equipment - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 49
TX is the DWT-B01, it should be worn on the hip. *Equipment other than TX (RX, boosters, etc.) should be constantly on. 10 Move the desired channel TX throughout the service area, and check settings also after installation. (AN-820 supports Auto only.) Making and Checking RF Settings (UHF) 49 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 50
Power down a different TX Antenna installation and setup Power up only desired channel TX Check service area for desired channel (single channel) Sufficient service area achieved? Yes To Step 3 Optimize antenna installation conditions 1. Determine Antenna installation location/orientation - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 51
close to the mouth. If the TX is the DWT-B01, it should be worn on the hip. * Equipment other than TX (RX, boosters, etc.) should be constantly on. 13 Make the parameter settings, and move the desired channel TX throughout the service area, checking at various locations. Sample settings for checking - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 52
held in the hand, close to the mouth. If the TX is the DWT-B01, it should be worn on the hip, and the person should stand at very high, this also can cause problems because the required D/U ratio cannot be obtained in the antenna vicinity. The resulting service area will be shaped like a doughnut - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 53
DWT-B01, it should be worn on the hip, and the person should stand at the rim of the stage, approaching the antenna. 17 Move the desired channel TX throughout the service specific channels with lots of movement, to enlarge the service area for these channels. However, because third-order - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 54
No requirements of step 3 was determined? Yes Flowchart for Step 5 Checking simultaneous multi-channel operation Power up all transmitters Check service area for desired channel Combination clearing requirements of step 4 was determined? Yes Change TX RF power and RX ATT level parameters - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 55
Configuring a DWX System Troubleshooting If noise, audio output dropout, or a decrease in the QL occurs, check the following. Is the RF level No too low? Is the RF level - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 56
exists. Remove computers, Bluetooth mice, mobile phones, game devices, and other signal transmitting devices away from the area. If the problem persists after removing the above, interference from another system may be present. Perform a clear channel scan, and reselect a frequency without - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 57
wireless LAN access points. ST mode and NT mode The Sony digital wireless system supports two types of remote control: ST mode where a transmitter to a network. One RMU-01 unit can control up to 82 transmitters. The service area range is about 10 meters from the Remote Control Unit RMU-01. Up to - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 58
Configuring a DWX System System configuration examples Configure the system while referring to the following examples. Configuring an ST mode system When operating from the receiver only One DWR-R01D or DWR-S01D unit Transmitters When operating from the receiver and a computer One DWR-R01D - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 59
Configuring a DWX System Configuring an NT mode system Notes When determining the number of RMU-01 units to use, refer to the "Installation of Remote Control Unit RMU-01" (page 62) section and take the coverage area of the RMU-01 into consideration. When supplying power to the RMU-01 via PoE, - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 60
can be controlled remotely. Using multiple RMU-01 units to enlarge the service area is also possible. Up to nine units can be used in one network 100Base-TX LAN card CD-ROM drive Ethernet hub information The RMU-01 supports PoE (Power over Ethernet). When the RMU-01 is connected to the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 61
one RMU-01 covers touches those on others, completely adjacent and with no gaps. 1) Radius: approx. 10 m (33 feet) 2) Front side (the side with SONY logo) When installing multiple RMU-01 units, place them so that strong signal area touches that of adjacent RMU-01 unit. Installation example 1 (plane - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 62
the signal emission characteristics, install facing the front side (the side with SONY logo) downward. 4) Ceiling 5) Wall 6) Floor Number of coverage area the coverage area by overlap, and a transmitter moves out of the service area of one RMU-01 unit, roaming occurs and the connection switches to - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 63
, installation of equipment is facilitated even in locations where providing a conventional power supply would be difficult. When an IEEE802.3af compliant hub with PoE support is connected to the network, or when a PoE power supply is connected between the RMU-01 and a regular hub, the RMU-01 can be - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 64
transmitter information received via WiDIF-HP and passed onto the network. Step 5 Checking the control function While checking whether the obtained service area fulfills the requirements, determine the installation location and number of RMU-01 units. 64 Making and Checking Network Settings - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 65
Configuring a DWX System 2.4 GHz area operation check Checking with the DWR-R01D display Use the "Cross Remote" control condition indication to check whether the transmitter is in the 2.4 GHz area. "Cross Remote" control condition indication "Cross Remote" control condition indication Indicates the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 66
Configuring a DWX System Step 1 Network Setup Specify the IP addresses and subnet masks of the devices connected to the network. Network configuration Configure a dedicated network for the DWX system, using 100Base-TX/10Base-T Ethernet equipment. Do not use an existing network. System precautions - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 67
Configuring a DWX System Computer network settings Use the regular procedure for the respective operating system to set the IP address and subnet mask of the computer. PC network settings The following procedure explains the setting operations using the Windows XP operating system. *For details - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 68
Configuring a DWX System RMU-01 network settings Install the setup tool supplied with the RMU-01 on the computer and make the RMU-01 network settings from the computer. Procedure Start the RMU-01 setup tool on the computer. Click the [Search Devices] button. Note On some computers equipped with - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 69
Configuring a DWX System Step 2 Checking Equipment Connections Verify that all devices connected to the network are correctly installed and set up. Checking the remote mode The display of the DWR-R01D can be used to check whether the receiver currently operates in ST mode or NT mode. To show the - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 70
overlapping subnet masks, or other problems. If necessary, re-assign IP addresses to the computer, DWR-R01D, and RMU-01 units, as described in "IP address setup" (page 67). Note Wireless Studio identifies the DWR-R01D and RMU-01 by IP address. The DWM-01/DWT-B01 are mutually identified by the DWR - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 71
if reception has been set up properly, there may be a problem with the UHF service area. Return to the channel plan selection and RF level setting stage service area line of sight to transmitters position overlooking service area Increasing RMU-01 unit count: Up to 9 units are supported Making - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 72
Configuring a DWX System Flowchart Step 1 Network setup to Establish network settings for each device Step 2 Checking equipment connections Check mode Check equipment count Does number of devices shown in Wireless Studio match actual number of devices? Yes Step 3 Checking for 2.4 GHz - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 73
Checking the control function Perform pairing No Repeat RF level setting (see page 45) Check control function service area Desired service area achieved? Re-assess 2.4 GHz service area 1. Change RMU-01 unit location 2. Increase RMU-01 unit count No Yes Setup procedure is complete. Making - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 74
Sample System Configaration Sample Minimum System Configuration (2 channels) The Digital Wireless Transmitter DWT-B01 and the Digital Wireless Receiver DWR-S01D are used in a one-on-one configuration. Transmitters Cross Remote via internal 2.4 GHz DWR-R01D Sample Small-Scale - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 75
Sample Medium-Scale System Configuration Using Antenna Divider WD-850 (17 channels or more) Transmitters RMU-01 UHF antenna RMU-01 Sample System Configaration 50-ohm terminator 50-ohm terminator 50-ohm terminator DWR-R01D (Total eight units) DWR-R01D (Total eight units) To AC power source - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 76
Sample System Configaration Sample Maximum System Configuration (82 channels) Transmitters UHF antenna WD-850 WD-850 Network connections are not illustrated here. 76 Making and Checking Network Settings - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 77
References References List of Supported Frequencies * December, 2010 Because there are no dedicated frequency bands for wireless use 59 60 61 62 63 64 65 66 67 68 69 DWM-01/F31 EU TX DWM-01/C31 EU DWT-B01/E EU DWT-P01/E EU RX DWR-R01D EU DWR-S01D EU AN-01 SYM UHF L ACC AN-820A M H WD- - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 78
Continuous operating time 5 hours (Ambient temperature 25 °C, using Sony LR6 AA-size alkaline batteries, 10 mW output, wireless remote Instructions (1) Spare battery case (1), Soft case (1), USB adapter cable (1), USB cable (1), Warranty Card (1) DWM-01/F31, DWM-01/C31, DWT-B01/E, DWT-P01 - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 79
100Mbps (automatic detection) RJ45-type, 8-pin (accepts PoE power) EIAJ-type4 Conforms to IEEE802.3af (supports mode A and B) 48 V DC 12 V DC 50 mA or less 100 mA or less adapter (2), Screws (1 set), Safety wire (1), Operating Instructions (1), CD-ROM (1), Warranty booklet (1) DWR-S01D Carrier - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 80
-20 to +60 °C Approx. 482 × 44 × 300 mm (excl. protruding parts) Approx. 4.6 kg AC power cord (1), 50-ohm terminator (6), 3P-2P adapter (1), Operating Instructions (1), Warranty Card (1) Note Old AN-820A's are not suitable for to use with DWR-R01D 12V DC power setting. Damage will occur to old AN - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 81
Making and Checking Network Settings 81 References - Sony DWM02/30 | Product Information Document (Digirtal Wireless System Integrati - Page 82
without notice. The values for mass and dimension are approximate. "Sony","make.believe","DWX","WiDIF" and "Cross Remote" are trademarks of Sony Corporation. All other trademarks are the property of their respective owners. Sony group has acquired a globally integrated ISO 14001 certification. For
Digital Wireless
Microphone System
System Integration Guide