Sony WI-SP600N Reference Guide
Sony WI-SP600N Manual
 |
View all Sony WI-SP600N manuals
Add to My Manuals
Save this manual to your list of manuals |
Sony WI-SP600N manual content summary:
- Sony WI-SP600N | Reference Guide - Page 1
estéreo inalámbricos con función de supresión de ruido Reference Guide Manuel de référence Guía de referencia WI-SP600N ©2018 Sony Corporation Printed in Malaysia 4-730-312-13(1) FCC ID: AK8WISP600N IC: 409B-WISP600N English FOR UNITED STATES CUSTOMERS. NOT APPLICABLE IN CANADA, INCLUDING IN - Sony WI-SP600N | Reference Guide - Page 2
pourrait ne pas se connecter à votre iPhone ou -bruit ou le Mode sonore ambiant pourrait Configuration requise pour la charge de la batterie via USB Adaptateur CA la unidad y el dispositivo Bluetooth. -- Hay un dispositivo con Wi-Fi o un horno de en este manual, consulte a su distribuidor Sony más
-
1 -
2
 |
 |
FCC ID: AK8WISP600N
IC: 409B-WISP600N
English
FOR UNITED STATES CUSTOMERS. NOT APPLICABLE
IN CANADA, INCLUDING IN THE PROVINCE OF
QUEBEC.
POUR LES CONSOMMATEURS AUX ÉTATS-UNIS.
NON APPLICABLE AU CANADA, Y COMPRIS LA
PROVINCE DE QUÉBEC.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
This equipment must not be co-located or operated in
conjunction with any other antenna or transmitter.
Note
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
–
Reorient or relocate the receiving antenna.
–
Increase the separation between the equipment and
receiver.
–
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
–
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Industry Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference;
and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
This equipment complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines and
RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed
to comply without testing of specific absorption rate (SAR).
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the countries
EEA (European Economic Area).
The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth SIG, Inc. and any use of
such marks by Sony Corporation is under license.
The N-Mark is a trademark or registered trademark of NFC
Forum, Inc. in the United States and in other countries.
Windows is a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
Apple, iPhone, iPod, iPod touch, macOS and Mac are
trademarks of Apple Inc., registered in the U.S. and other
countries.
Use of the Made for Apple badge means that an accessory
has been designed to connect specifically to the Apple
product(s) identified in the badge, and has been certified by
the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
Android is a trademark of Google LLC.
Other trademarks and trade names are those of their
respective owners.
Precautions
On BLUETOOTH® communications
•
Bluetooth wireless technology operates within a range of
about 10 m (30 feet). Maximum communication range may
vary depending on obstacles (human body, metal, wall,
etc.) or electromagnetic environment.
•
Bluetooth communications may be disabled, or noise or
audio dropout may occur under the following conditions.
–
There is a human body between the unit and the
Bluetooth device.
This situation may be improved by placing the Bluetooth
device facing the antenna of the unit.
–
There is an obstacle, such as metal or a wall, between
the unit and the Bluetooth device.
–
A Wi-Fi device or microwave oven is in use, or
microwaves are emitted near the unit.
–
The antenna is built into the unit as illustrated in the
dotted line.
The sensitivity of the Bluetooth communications will
improve by removing any obstacles between the
connected Bluetooth device and the antenna of this unit.
•
Because Bluetooth devices and Wi-Fi (IEEE802.11b/g/n) use
the same frequency (2.4 GHz), microwave interference may
occur resulting in noise or audio dropout or
communications being disabled if this unit is used near a
Wi-Fi device. In such a case, perform the following.
–
Use this unit at least 10 m (30 feet) away from the Wi-Fi
device.
–
If this unit is used within 10 m (30 feet) of a Wi-Fi device,
turn off the Wi-Fi device.
–
Install this unit and the Bluetooth device as near to each
other as possible.
•
Microwaves emitting from a Bluetooth device may affect
the operation of electronic medical devices. Turn off this
unit and other Bluetooth devices in the following locations,
as it may cause an accident:
–
where inflammable gas is present, in a hospital, or a
petrol station
–
near automatic doors or a fire alarm.
•
Due to the characteristic of the wireless technology, the
sound played on this unit is delayed from the sound and
music played on the sending device. Therefore, the image
and sound may be misaligned when viewing a movie or
playing a game.
•
This product emits radio waves when used in wireless
mode.
When used in wireless mode on an airplane, follow flight
crew directions regarding permissible use of products in
wireless mode.
•
This unit supports security capabilities that comply with
the Bluetooth standard to provide a secure connection
when the Bluetooth wireless technology is used, but
security may not be enough depending on the setting. Be
careful when communicating using Bluetooth wireless
technology.
•
We do not take any responsibility for the leakage of
information during Bluetooth communications.
•
Connection with all Bluetooth devices cannot be
guaranteed.
–
A device featuring Bluetooth function is required to
conform to the Bluetooth standard specified by
Bluetooth SIG, Inc. and be authenticated.
–
Even if the connected device conforms to the above
mentioned Bluetooth standard, some devices may not
be connected or work correctly, depending on the
features or specifications of the device.
–
While talking on the phone hands free, noise may occur,
depending on the device or communication
environment.
•
Depending on the device to be connected, it may require
some time to start communications.
If sound skips frequently during playback
•
The situation may be improved by setting the sound
quality mode to “priority on stable connection.” For details,
refer to the Help Guide.
•
The situation may be improved by changing the wireless
playback quality settings or fixing the wireless playback
mode to SBC on the transmitting device. For details, refer
to the operating instructions supplied with the
transmitting device.
•
If you are using a smartphone, the situation may be
improved by shutting down unnecessary applications or
rebooting the smartphone.
On the use of calling apps for smartphones and
computers
•
This unit supports normal incoming calls only. Calling apps
for smartphones and computers are not supported.
On charging the unit
•
This unit can be charged using USB only. Personal
computer with USB port is required for charging.
•
This unit cannot be turned on, nor can the Bluetooth and
noise canceling functions be used, during charging.
•
If you do not use the unit for a long time, the rechargeable
battery may not be able to keep sufficient charge. The
battery will be able to keep a charge properly after
repeatedly discharging and charging several times.
•
If you store the unit for a long time, charge the battery
once every half year to prevent over-discharge.
•
If the length of time you can use the unit became
extremely short, the rechargeable battery should be
replaced with a new one. Please contact your nearest Sony
dealer for a battery replacement.
•
Make sure to close the micro-USB port cover securely after
charging.
Note on static electricity
•
Static electricity accumulated in the body may cause mild
tingling in your ears. To minimize the effect, wear clothes
made from natural materials.
If the unit does not operate properly
•
Reset the unit.
Press the
and – buttons simultaneously while charging.
The unit will be reset. Pairing information is not deleted.
–
•
If the problem persists even after the resetting operation
above, initialize the unit as follows.
Disconnect the micro-USB cable from the micro-USB port,
turn off the unit, then hold down the
and
buttons
simultaneously for more than 7 seconds.
The indicator (blue) flashes 4 times, and the unit is reset to
the factory settings. All pairing information is deleted.
•
After the unit is initialized, it may not connect to your
iPhone or computer. In this case, delete the pairing
information of the unit from the iPhone or computer, and
then pair them again.
What is noise canceling?
•
The noise canceling circuit actually senses outside noise
with built-in microphones and sends an equal-but-
opposite canceling signal to the unit.
–
The noise canceling effect may not be pronounced in a
very quiet environment, or some noise may be heard.
–
Depending on how you wear the unit, the noise
canceling effect may vary or a beeping sound (howling)
may occur. In these cases, take off the unit and put it on
again.
–
The noise canceling function works for noise in the low
frequency band primarily. Although noise is reduced, it is
not canceled completely.
–
When you use the unit in a train or a car, noise may
occur depending on street conditions.
–
Mobile phones may cause interference and noise.
Should this occur, locate the unit further away from the
mobile phone.
–
Do not cover the microphones of the unit with your
hands. The noise canceling function or the Ambient
Sound Mode may not work properly, or a beeping sound
(howling) may occur. In these cases, take your hands off
of the microphones of the unit.
Microphones
On wearing the unit
•
After use, remove the headphones slowly.
•
Because the headphones are of a high density enclosure,
forcing them against your ears may result in eardrum
damage.
Pressing the headphones against your ears may produce a
diaphragm click sound. This is not a malfunction.
Water resistant performance of this unit
•
The water resistant specifications of this unit are
equivalent to IPX4
1)
in IEC 60529 “Degrees of protection
against ingress of water (IP Code)”, which specifies the
degree of protection provided against the entry of water.
(Make sure that the micro-USB port cover is closed
securely when you use the unit.) However, the unit
cannot be used in water. Unless the unit is used
correctly, water may get into the unit and cause fire,
electrocution, or malfunctions.
Note the following cautions carefully and use the unit
correctly.
1)
IPX4 (degree of protection against splashing water):
Protected against water splashing from any direction.
Liquids that the water resistant performance
specifications apply to
Applicable:
Fresh water, tap water, perspiration
Not applicable:
Liquids other than those above
(examples: soapy water, detergent water, water with
bath agents, shampoo, hot spring water, pool water,
seawater, etc.)
Water resistant performance of the unit is based on
Sony measurements under the conditions described
above. Note that malfunctions as a result of water
immersion caused by misuse by the customer are not
covered by the warranty.
To maintain water resistant performance
Note the following cautions carefully and use the unit
correctly.
•
The micro-USB port cover is important for maintaining
water resistant performance. Make sure the micro-USB
port cover is closed securely when you use the unit. If
the cover has any foreign objects on it or is not
completely closed, water resistant performance cannot
be maintained. In addition, water may get into the unit
and cause malfunctions.
•
Do not splash water forcibly against the cylindrical part
from which sound is emitted. Doing so may deteriorate
the water resistant performance of the unit.
•
Do not put the unit in water or use it in a humid place
such as a bathroom.
•
Do not drop the unit or expose it to mechanical shock.
Doing so may deform or damage the unit, resulting in
deterioration of water resistance performance.
•
Wipe off with a soft dry cloth any water that gets on the
unit. If water remains in the earbud holes, the sound
may seem low or not be audible at all. In this case,
remove the earbuds, face the sound conduit downward,
and shake the sound conduit a couple of times.
•
Do not leave the unit with water on it in cold places as
the water may freeze. In order to avoid malfunctions,
make sure that you wipe off water after use.
•
If the unit is cracked or deformed, refrain from using the
unit near water or contact your nearest Sony dealer.
Others
•
Do not place this unit in a place exposed to humidity, dust,
soot or steam, or subject to direct sunlight. Do not leave
the unit in a car for a long time. It may cause a
malfunction.
•
Using the Bluetooth device may not function on mobile
phones, depending on radio wave conditions and location
where the equipment is being used.
•
High volume may affect your hearing.
•
For traffic safety, do not use while driving or cycling.
•
Do not use the unit in places where it would be dangerous
if you are unable to hear ambient sound, such as at
railroad crossings, train station platforms, and construction
sites.
•
Keep earbuds clean. To clean the earbuds, wash them with
a mild detergent solution.
•
Do not subject the unit to excessive shock.
•
Clean the unit with a soft dry cloth.
•
Do not expose the unit to water.
Remember to follow the precautions below.
–
Be careful not to drop the unit into a sink or other
container filled with water.
–
Do not use the unit in humid locations or bad weather,
such as in the rain or snow.
•
If you experience discomfort after using the unit, stop
using the unit immediately.
•
Install the earbuds firmly. If an earbud accidentally
detaches and is left in your ear, it may cause injury.
•
Since children may swallow small parts such as an earbud,
keep the unit out of reach of children.
•
If you have any questions or problems concerning this unit
that are not covered in this manual, please consult your
nearest Sony dealer.
Long Hybrid silicone rubber earbuds are consumables. If
they are damaged or deteriorated, consult your nearest
authorized Sony retailer or www.sony.com to replace
them.
Optional replacement arc supporters can be ordered from
your nearest authorized Sony retailer or www.sony.com.
Compatible iPhone/iPod
models
You can use the unit with only the following models. Update
your iPhone or iPod to the latest software before use.
•
iPhone 7
•
iPhone 7 Plus
•
iPhone SE
•
iPhone 6s
•
iPhone 6s Plus
•
iPhone 6
•
iPhone 6 Plus
•
iPhone 5s
•
iPhone 5c
•
iPhone 5
•
iPod touch (6th generation)
(As of December 2017)
Specifications
General
Communication system:
Bluetooth Specification version 4.1
Output:
Bluetooth Specification Power Class 2
Maximum communication range:
Line of sight approx. 10 m
(30 ft)
1)
Frequency band:
2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Compatible Bluetooth profiles
2)
:
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HFP (Hands-free Profile)
HSP (Headset Profile)
Supported Codec
3)
:
SBC
4)
, AAC
5)
Supported content protection method:
SCMS-T
Transmission range (A2DP):
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
Included items:
Wireless noise canceling stereo headset (1)
Micro-USB cable (approx. 50 cm (19 3/4 in.)) (1)
Long Hybrid silicone rubber earbuds (SS/S/M/L 2 each)
Arc supporters (M/L 2 each)
Reference Guide (this sheet) (1)
Operating Instructions (1)
Other documents (1 set)
1)
The actual range will vary depending on factors such as
obstacles between devices, magnetic fields around a
microwave oven, static electricity, reception sensitivity,
antenna’s performance, operating system, software
application, etc.
2)
Bluetooth standard profiles indicate the purpose of
Bluetooth communications between devices.
3)
Codec: Audio signal compression and conversion format
4)
Subband Codec
5)
Advanced Audio Coding
Wireless noise canceling stereo
headset
Power source:
DC 3.7 V: Built-in lithium-ion rechargeable battery
DC 5 V: When charged using USB
Mass:
Approx. 21 g (0.74 oz)
Operating temperature:
0 °C to 40 °C (32 °F to 104 °F)
Usage hours:
When connecting via the Bluetooth device
Music playback time:
Max. 6 hours (NC ON), Max. 6 hours (NC OFF)
Communication time:
Max. 6.5 hours (NC ON), Max. 6.5 hours (NC OFF)
Standby time:
Max. 10 hours (NC ON), Max. 200 hours (NC OFF)
Note: Usage hours may be shorter depending on the
Codec and the conditions of use.
Charging time:
Approx. 1.5 hours
(About 60 minutes of music playback is possible after
15 minutes charging.)
Note: Charging hours may be different depending on
the conditions of use.
Charging temperature:
5 °C to 35 °C (41 °F to 95 °F)
Receiver
Type:
Closed, Dynamic
Driver unit:
6 mm
Microphone
Type:
Electret condenser
Directivity:
Omni directional
Effective frequency range:
50 Hz - 8,000 Hz
System requirements for battery
charge using USB
USB AC adaptor
A commercially available USB AC adaptor capable of feeding
in more than 0.5 A (500 mA)
Personal Computer
(As of December 2017)
Personal Computer with pre-installed with any of the
following operating systems and USB port:
Operating Systems:
(when using Windows)
Windows
®
10 Home / Windows
®
10 Pro
Windows
®
8.1 / Windows
®
8.1 Pro
Windows
®
8 / Windows
®
8 Pro
Windows
®
7
Home Basic / Home Premium / Professional / Ultimate
(when using Mac)
macOS (version 10.9 or later)
Design and specifications are subject to change without
notice.
Français
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Cet équipement est conforme aux limites d’exposition aux
rayonnements énoncées pour un environnement non
contrôlé et respecte les règles les radioélectriques (RF) de la
FCC lignes directrices d’exposition et d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Cet
équipement émet une énergie RF très faible qui est
considérée comme conforme sans évaluation du débit
d’absorption spécifique (DAS).
La validité du marquage CE est limitée uniquement aux pays
dans lesquels il fait force de loi, c’est-à-dire principalement
dans les pays de I’EEE (Espace Économique Européen).
La marque et les logos Bluetooth® sont des marques
déposées de Bluetooth SIG, Inc. qui sont utilisées sous
licence uniquement par Sony Corporation.
N-Mark est une marque commerciale ou une marque
déposée de NFC Forum, Inc. aux États-Unis et dans d’autres
pays.
Windows est une marque déposée ou une marque de
commerce de Microsoft Corporation aux États-Unis et/ou
dans d’autres pays.
Apple, iPhone, iPod, iPod touch, macOS et Mac sont des
marques de commerce d’Apple Inc., déposées aux États-Unis
et dans d’autres pays.
L’utilisation du badge Made for Apple signifie qu’un
accessoire a été conçu pour être raccordé spécifiquement au
produit ou aux produits Apple identifiés dans le badge, et a
été certifié par le constructeur pour satisfaire les normes de
performance d’Apple. Apple n’est pas responsable du
fonctionnement de cet appareil ni de sa conformité avec les
consignes et normes de sécurité.
Android est une marque commerciale de Google LLC.
Les autres marques commerciales et noms commerciaux
appartiennent à leurs propriétaires respectifs.
Précautions
Communications BLUETOOTH®
•
La technologie sans fil Bluetooth fonctionne dans un rayon
d’environ 10 m (30 pieds). La portée de communication
maximale peut varier en fonction des obstacles
(personnes, objets métalliques, murs, etc.) ou de
l’environnement électromagnétique.
•
Les communications Bluetooth peuvent être désactivées
ou du bruit ou une diminution sonore peut survenir dans
les conditions suivantes.
–
Une personne se trouve entre l’appareil et le
périphérique Bluetooth.
Vous pourriez améliorer la situation en plaçant le
périphérique Bluetooth face à l’antenne de l’appareil.
–
Un obstacle, par exemple un objet métallique ou un mur,
se trouve entre l’appareil et le périphérique Bluetooth.
–
Un périphérique Wi-Fi ou un four micro-ondes est utilisé
ou des hyperfréquences sont émises à proximité de
l’appareil.
–
L’antenne est intégrée dans l’appareil, comme illustré à
l’aide de la ligne pointillée.
La sensibilité des communications Bluetooth peut être
améliorée par le retrait des obstacles entre le
périphérique Bluetooth connecté et l’antenne de cet
appareil.
•
Comme les périphériques Bluetooth et Wi-Fi (IEEE802.11b/
g/n) utilisent la même fréquence (2,4 GHz), des
interférences en hyperfréquences peuvent se produire et
entraîner des parasites, des pertes de niveau audio ou
l’interruption des communications si cet appareil est utilisé
à proximité d’un périphérique Wi-Fi. En pareil cas, prenez
les mesures suivantes.
–
Utilisez cet appareil à une distance d’au moins 10 m (30
pieds) du périphérique Wi-Fi.
–
Si cet appareil est utilisé à moins de 10 m (30 pieds) d’un
périphérique Wi-Fi, éteignez le périphérique Wi-Fi.
–
Installez cet appareil et le périphérique Bluetooth aussi
près que possible l’un de l’autre.
•
Les émissions d’hyperfréquences d’un périphérique
Bluetooth peuvent perturber le fonctionnement des
appareils médicaux électroniques. Pour éviter de causer un
accident, éteignez cet appareil et les autres périphériques
Bluetooth dans les endroits suivants :
–
en présence de gaz inflammable, dans un hôpital ou une
station-service
–
à proximité de portes automatiques ou d’un avertisseur
d’incendie.
•
En raison des caractéristiques de la technologie sans fil, le
son reproduit sur cet appareil est décalé par rapport au
son et à la musique en cours de lecture sur le périphérique
émetteur. Par conséquent, l’image et le son peuvent être
désalignés lorsque vous visionnez un film ou jouez à un
jeu.
•
Ce produit émet des ondes radio lors de l’utilisation en
mode sans fil.
Lors de l’utilisation en mode sans fil dans un avion, suivez
les instructions de l’équipage concernant l’utilisation
permise des produits en mode sans fil.
•
Cet appareil prend en charge les caractéristiques de
sécurité conformes à la norme Bluetooth pour offrir une
connexion sécurisée lors de l’utilisation de la technologie
sans fil Bluetooth; cependant, la sécurité pourrait être
insuffisante selon le réglage. Soyez prudent lorsque vous
communiquez au moyen de la technologie sans fil
Bluetooth.
•
Nous ne pouvons être tenus responsables de la fuite
d’informations survenant lors de communications
Bluetooth.
•
La connexion ne peut pas être garantie avec tous les
périphériques Bluetooth.
–
Un périphérique doté de la fonction Bluetooth est
nécessaire pour la conformité à la norme Bluetooth
spécifiée par Bluetooth SIG, Inc. et pour
l’authentification.
–
Même si le périphérique connecté est conforme à la
norme Bluetooth mentionnée précédemment, certains
périphériques peuvent ne pas se connecter ou ne pas
fonctionner correctement, selon leurs caractéristiques ou
spécifications.
–
Selon le périphérique ou l’environnement de
communication, des parasites peuvent se produire lors
des communications téléphoniques en mains libres.
•
Selon le périphérique à connecter, le démarrage des
communications peut prendre un certain temps.
Si le son est fréquemment saccade pendant la lecture
•
Vous pourriez améliorer la situation en réglant le mode de
qualité sonore à « priorité à la connexion stable ». Pour plus
de détails, reportez-vous au manuel d’aide.
•
Vous pourriez améliorer la situation en modifiant les
réglages de qualité de lecture sans fil ou en réglant le
mode de lecture sans fil à SBC sur le périphérique
émetteur. Pour plus de détails, reportez-vous au mode
d’emploi fourni avec le périphérique émetteur.
•
Si vous utilisez un téléphone intelligent, vous pourriez
améliorer la situation en fermant des applications inutiles
ou en redémarrant le téléphone intelligent.
À propos de l’utilisation d’applications d’appel pour
les téléphones intelligents et ordinateurs
•
Cet appareil prend uniquement en charge les appels
entrants normaux. Les applications d’appel pour les
téléphones intelligents et ordinateurs ne sont pas prises
en charge.
Chargement de l’appareil
•
Cet appareil peut être chargé uniquement par USB. Un
ordinateur personnel avec port USB est requis pour le
chargement.
•
Lors du chargement, il n’est pas possible de mettre cet
appareil en marche ni d’utiliser les fonctions Bluetooth et
de réduction de bruits.
•
Si vous n’utilisez pas l’appareil pendant une période
prolongée, la batterie rechargeable risque de ne pas
fournir une charge suffisante. La batterie pourra fournir
une charge adéquate après plusieurs chargements et
déchargements.
•
Si vous rangez l’appareil pendant une période prolongée,
chargez la batterie tous les six mois pour éviter un
déchargement excessif.
•
Si la durée d’utilisation de l’appareil devient très courte,
vous devez remplacer la batterie rechargeable par une
nouvelle. Veuillez contacter votre détaillant Sony le plus
proche afin de remplacer la batterie.
•
Vérifiez que le couvercle du port micro-USB est bien fermé
après le chargement.
Remarque à propos de l’électricité statique
•
L’électricité statique accumulée dans votre corps peut
causer de légers fourmillements dans vos oreilles. Vous
pouvez atténuer cet effet en portant des vêtements en
matière naturelle.
Si l’appareil ne fonctionne pas correctement
•
Réinitialisez l’appareil.
Appuyez sur les boutons
et – simultanément pendant le
chargement. L’appareil sera réinitialisé. Les informations de
jumelage ne sont pas supprimées.
–
WI-SP600N
©2018 Sony Corporation
Printed in Malaysia
4-730-312-
13
(1)
Wireless noise canceling stereo headset
Casque stéréo sans fil réducteur de bruits
Auriculares estéreo inalámbricos con función de supresión de ruido
Reference Guide
Manuel de référence
Guía de referencia