Stihl HOS Instruction Manual

Stihl HOS Manual

Get Stihl HOS PDF manuals and user guides View all Stihl HOS manuals
Add to My Manuals
Save this manual to your list of manuals

Stihl HOS manual content summary:

  • Stihl HOS | Instruction Manual - Page 1
    STIHL HOS STIH) Instruction Manual
  • Stihl HOS | Instruction Manual - Page 2
    ANDREAS STIHL AG & Co. KG, 2004 0458 522 0121. M0,1. F4. T. Printed in Germany Printed on chlorine-free paper. Printing inks contain vegetable oils; paper can be recycled. BA_SE_016_002_01_04.fm Contents Guide to Using this Manual 2 Safety Precautions 3 Applications 4 Assembling the Sharpener
  • Stihl HOS | Instruction Manual - Page 3
    English Guide to Using this Manual Pictograms All the pictograms attached to the machine are shown and explained in this manual. The operating and handling instructions are supported by illustrations. Symbols in text The individual steps or procedures described in the manual may be marked in
  • Stihl HOS | Instruction Manual - Page 4
    . Only perform the adjustments and maintenance operations described in this manual. All other maintenance and repairs should be carried out by your STIHL dealer. Only use original STIHL replacement parts. In the interests of your own safety, never modify your electric sharpener in any way. HOS 3
  • Stihl HOS | Instruction Manual - Page 5
    KN 523BA046 KN English Applications Assembling the Sharpener The STIHL HOS sharpens all STIHL Oilomatic saw chains with the exception of carbide-tipped chains (RD, RDS). All the necessary setting data and grinding wheels are listed in the instruction sheet 0457 717 0000. A 1 2 1 : Loosen the
  • Stihl HOS | Instruction Manual - Page 6
    up the holes. : Insert M4x12 screws (13) in the holes and fit the M4 nuts (14). : Tighten down the screws firmly. : Refit the guard plate. HOS 5
  • Stihl HOS | Instruction Manual - Page 7
    in the spacer (4). Push the onto the motor shaft (5) (spacer flange must face away from motor). : Fit the required grinding wheel (6) - see instruction sheet or "Special Accessories" - with its rounded side facing the motor : Fit the thrust washer (7) on the shaft with its raised side facing away
  • Stihl HOS | Instruction Manual - Page 8
    -hand thread. : Remove the locking pin. : Refit the guard plate. 1 4 2 5 6 : Engage pin (1) on underside of swivelling tool rest in hole (2) in sharpener's base. : Insert M8 x 60 round head square neck bolt (3) through the slot (4). : Fit the washer (5) and tighten moderately with the M8 wingnut
  • Stihl HOS | Instruction Manual - Page 9
    in each case. : Insert the two M6x8 pan head screws (2) through the clamping rail and screw them into the guide rail. : Push clamping lever's screw (6) through the center hole in the swivelling tool rest and the thrust pad (7). : Fit the nut (8) and tighten down the clamping lever firmly. 8 HOS
  • Stihl HOS | Instruction Manual - Page 10
    Preparations for Sharpening English 523BA012 KN 523BA061 KN 523BA062 KN 4 2 3 1 Do not switch on the motor yet. : Replace cutters with severely worn or (2) downward, in the clamping rail (3) - cutting edges must point to the left. : Pull the master cutter back against the stop (4). HOS 9
  • Stihl HOS | Instruction Manual - Page 11
    7 The stop's pivot pin (5) moves backward and forward in the arm. : To sharpen the left-hand row of cutters: Pull the stop in the direction of arrow. Set the scale (6) on the swivelling tool rest to the specified sharpening angle (see separate data sheet). : Tighten down the wingnut (7). Lateral
  • Stihl HOS | Instruction Manual - Page 12
    adjusting screw in position with the knurled nut. Initial Adjustment of Grinding Depth : Use the handle (10) to move the motor arm down until the HOS 11
  • Stihl HOS | Instruction Manual - Page 13
    and readjust - see "Lateral Adjustment" in chapter "Preparations for Sharpening". : Sharpen the side plate by applying the wheel several times - do not sharpen in a single pass. : When result is satisfactory, check the to its neutral position. : Put on safety glasses. : Switch on the motor. 12 HOS
  • Stihl HOS | Instruction Manual - Page 14
    English 523BA022 KN 523BA070 KN 523BA071 KN 1 : Use a filing gauge to check sharpening data. The travel limiting screw must now butt against the stop lug and the side plate angle (1) should clamping lever. Pull the chain to the left until the stop is behind the next cutter but one. HOS 13
  • Stihl HOS | Instruction Manual - Page 15
    stop if necessary. : Now sharpen the second row of cutters. Checking Depth Gauge Setting : Select the filing gauge (special accessory) that matches the chain pitch (see separate instruction sheet). 523BA072 KN : on the swivelling tool rest to "0" and tighten down the M8 wingnut firmly. 14 HOS
  • Stihl HOS | Instruction Manual - Page 16
    1 Fitting the Grinding Wheel : Select grinding wheel (see separate instruction sheet). : Perform ringing test. : Mount the grinding wheel Lateral Stop : Swing the motor arm down. : Slide the chain along the guide rail until the profile (1) of the grinding wheel is centered above the depth . HOS 15
  • Stihl HOS | Instruction Manual - Page 17
    the depth gauges are too low. On PM1 and RM2 chains the rear hump of the tie strap (with service mark) is lowered at the same time as the depth gauge. The other parts of the triple-humped tie rest to "0". : Use dressing stone (special accessory) to correct the profile of the grinding wheel. 16 HOS
  • Stihl HOS | Instruction Manual - Page 18
    wheel Cooling air inlets Accessible screws and nuts Shield Clamp and guide rail Stop and lock 1) Have work performed by qualified X X X X X X before starting work after finishing work or daily weekly monthly if problem if damaged as required English X X X X X X X X X X X X X HOS 17
  • Stihl HOS | Instruction Manual - Page 19
    -observance of the safety precautions, operating and maintenance instructions in this manual. This includes in particular: - Alterations or modifications to the product not approved by STIHL. - Using attachments or sharpening tools not approved by STIHL. - Using the product for purposes for which it
  • Stihl HOS | Instruction Manual - Page 20
    Main Parts of Sharpener 7 4 11 2 1 10 8 65 3 Specifications English Motor Type: Single-phase AC, KN 1 Motor 2 Switch box 3 Swivelling tool rest 4 Motor arm 5 Clamping lever 6 Thrust pad HOS 7 Travel limiting screw 8 Stop 9 Adjusting screw 10 Grinding wheel 11 Stop lug 1) according to EN
  • Stihl HOS | Instruction Manual - Page 21
    maintenance operations described in this manual. Other repair work may be performed only by an authorized STIHL dealer. Warranty claims following an authorized STIHL dealer using original STIHL replacement parts. Original STlHL parts can be identified by the STIHL part number, the STIHl logo and
  • Stihl HOS | Instruction Manual - Page 22
    identification: Universal sharpener STIHL HOS 5202 Technical documents deposited at: Andreas Stihl AG & Co. KG Product Licensing Done at Waiblingen, September 1,2003 Andreas Stihl AG & Co 61000-3-3 and EN 60204-1 Steinhauser Director Group Product Management Engineering Services English HOS 21
  • Stihl HOS | Instruction Manual - Page 23
    comply with the highest quality standards. An independent organization has certified that all products manufactured by STIHL meet the strict requirements of the ISO 9001 standard for quality management systems in terms of product development, materials purchasing, production, assembly, documentation
  • Stihl HOS | Instruction Manual - Page 24
    English HOS 23
  • Stihl HOS | Instruction Manual - Page 25
    English 24 HOS
  • Stihl HOS | Instruction Manual - Page 26
    0458 522 0121 englisch / English
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Instruction Manual
STIH)
STIHL HOS