Sub-Zero UC-15I Ice Maker Installation Guide
Sub-Zero UC-15I Manual
 |
View all Sub-Zero UC-15I manuals
Add to My Manuals
Save this manual to your list of manuals |
Sub-Zero UC-15I manual content summary:
- Sub-Zero UC-15I | Ice Maker Installation Guide - Page 1
INSTALLATION GUIDE Undercounter Ice Machine - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 2
Contents Undercounter Ice Machine 3 Ice Machine Specifications 4 Ice Machine Installation 8 Installation Checklist 14 Service Information 15 Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-todate information. IMPORTANT NOTE: - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 3
Undercounter Ice Machine 3 subzero.com/specs Sub-Zero Undercounter Ice Machine IMPORTANT NOTE: The importance of the installation of the Sub-Zero ice machine cannot be overemphasized. Installation must be completed by a qualified installer. Read this entire installation guide prior to installation - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 4
Ice Machine Specifications 4 Ice Machine Specifications OVERALL DIMENSIONS 143/4" (375) 23" (584) 335/8" (854) 4" (102) INSTALLATION 24" (610) OPENING DEPTH Ice Storage Capacity Shipping Weight 26 lbs (12 kg) 117 lbs (53 kg) IMPORTANT NOTE: It is recommended that the electrical and water - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 5
within the opening, additional cabinet depth may be required. Refer to the illustration below. Models UC15IO and UC-15IPO are designed and safe for use in outdoor applications. When installed outdoors, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 6
Specifications 6 Plumbing Requirements The ice machine must be installed with adequate clearance for water and drain connections at the rear of the unit. Prepare the water supply line and drain connection before installing the ice machine. Improper water supply and drain connections can result - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 7
Ice Machine Specifications 7 subzero.com/specs Plumbing Requirements DRAIN CONNECTION Models UC-15I and UC-15IO are gravity drain models that require a drain tube that is pitched down from the outlet at the back of the unit to the sanitary sewer connection. Models UC-15IP and UC-15IPO have a built - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 8
the ice maker into position near the installation opening. Remove and discard all packing materials. Remove the literature packet and drain hose from inside the ice machine. The bin thermostat clip is shipped with tape holding it in position. Remove the tape. Also, remove the tape securing the water - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 9
Ice Machine Installation 9 subzero.com/specs Installation INSTALL THE ICE MACHINE 1) Adjust the leveling legs close to the desired height. Refer to the illustration below. 2) Reverse the door swing if needed. Refer to steps outlined on the following pages. 3) Gravity drain models: Install the - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 10
Ice Machine Installation 10 Reverse Door Swing The hinged side of the door may be reversed to the other side if needed. The ice machine is the two screws that secure it to the door. Refer to the illustration below. Replace it with the left-hand upper trim. 4) Transfer the hinges to the left - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 11
Ice Machine Installation 11 subzero.com/specs Reverse Door Swing 5) Remove the ice machine top cover by removing the two screws along the back of the unit. Refer to the illustration below. 6) Remove four screws from the front top - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 12
Ice Machine Installation 12 Panel Installation DOOR PANEL INSTALLATION You should be sure of the door panel size and placement before proceeding with the installation. Refer to the chart for panel specifications. If you have questions, contact your authorized Sub-Zero dealer or cabinet supplier. - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 13
Ice Machine Installation 13 subzero.com/specs Panel Installation Exercise caution when drilling holes for mounting hardware. This is especially grit sandpaper. Wipe with alcohol to ensure that the surface is clean and dry. Use an appliance or industrial grade, oil base, high gloss enamel paint. - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 14
been installed in accordance with all applicable electrical codes? Is the water supply turned on? Have water supply and drain connections been examined for leaks? Is the ice machine drain line routed to an open site drain for gravity drains and according to instructions for drain pump models? Has - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 15
your ice machine by calling Sub-Zero factory certified service. For the name and number of Sub-Zero factory certified service nearest you, check the contact & support section of our website, subzero.com or call Sub-Zero customer care at 800-222-7820. When calling for service, you will need the model - Sub-Zero UC-15I | Ice Maker Installation Guide - Page 16
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7023608 REV-A 8/2011
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Undercounter Ice Machine
INSTALLATION GUIDE