TASCAM IF-FW/DM Installation and Use v 2.0 Manual Addendum

TASCAM IF-FW/DM Manual

Get TASCAM IF-FW/DM PDF manuals and user guides View all TASCAM IF-FW/DM manuals
Add to My Manuals
Save this manual to your list of manuals

TASCAM IF-FW/DM manual content summary:

  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 1
    DM-24 Digital Mixing Console 9101446901 Version 2.0 - RELEASE NOTES
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 2
    Fade 23 Motorized faders 23 Miscellaneous changes 24 High-speed digital format restored 24 Flattening an EQ band 24 External switch (footswitch) functionality ...24 Block diagram (normal 25 Block diagram (high-speed 26 Level diagram 27 Acknowledgements 28 2 TASCAM DM-24 Reference Manual
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 3
    of the DM-24 software and the earlier version as explained in the manual. You should keep this page together with the existing manual for easy TASCAM recommends that you take your DM-24 to a TASCAM service center to be upgraded. If you are upgrading the firmware yourself, note that TASCAM supports
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 4
    of the tape returns to the stereo buss (and hence the monitoring). Aux 1-6 can be used as six mono, or three stereo, studio cue feeds. 4 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 5
    the main manual). On-screen fader adjustment It is now possible to move the cursor to the on-screen fader representation in the module screen and use POD 4 to adjust the level of the fader. This allows you to make the smallest possible increments to the fader supported by the DM-24. You may
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 6
    DM-24 version 2.0-Release notes-Module screens Channel selection following solo In the PREFERENCES page, it is now possible to set a new option prefader Aux sends may be muted along with the rest of the channel. This is available from the OPTION PREFERENCES screen: 6 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 7
    slot interface card. An example DM analog I/O slot card. This leaves the assignable I/O free for insert purposes. This could be used for six effect sends in analog format, or to drive headphone amplifiers, etc. Note that only six of the outputs are used here (7 and 8 are not used). TASCAM DM-24
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 8
    here. Support of TDIF optional slot card The TDIF optional slot card is now supported for use with the DM-24. However, This can be useful when working with a DAW fitted with a TDIF interface. Additionally, this stereo mix can also be output from the ADAT and time). 8 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 9
    other uses. For example, at mixdown, using an IF-AN/DM slot card, you could assign the eight buss outputs to the analog outputs provided by the card, and then route these back to channels 25-32, where value! Use the ASSIGN BUSS screen to make these assignments. TASCAM DM-24 2.0 release notes 9
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 10
    DM-24 version 2.0-Release notes-I/O setup changes 1 Navigate to the bottom line of the screen, and select the appropriate effect return or assignable return. 2 1-2 as a tape return path, and frees up the aux sends for use as multiple cue mixes and effect sends. 10 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 11
    2.0-Release notes-I/O setup changes No assignment to a channel When you are making assignments to the DM-24, as described in "Assigning inputs to channels" on page 40, a new "source" has 000). These "new" channels are perfect for use as MIDI instrument channels. TASCAM DM-24 2.0 release notes 11
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 12
    DM-24 version 2.0-Release notes-I/O setup changes If an optional IF-AN/DM analog card is fitted, (see "New output assignment had to be paired (1-2, etc.,) in order to output them from the digital outputs. 12 TASCAM DM-24 2.0 release notes You can use the AUX 1-2 LEVEL and AUX 1-2 PAN/BAL screens to
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 13
    DM-24 version 2.0-Release notes-Surround mode It is now possible to select individual (mono) Aux send busses for output in this way. In for these effect tracks (an on-screen switch is also provided). The switch and percentage level are shown in the screen above. TASCAM DM-24 2.0 release notes 13
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 14
    DM-24 version 2.0-Release notes-Surround mode Circle and square patterns (using the dial) Note that you can now use the dial of the room Right center Left front Center Right front L-F C R-F + L-C Room R-C middle R-L R-C R-R Note that these moves can be automated. 14 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 15
    DM-24 version 2.0-Release notes-Effects (TC Works reverb) Effects (TC Works reverb) A new setting has been added to the previous three settings the EFFECT Settings box means that the values chosen for the effects will remain when the new snapshot is loaded. TASCAM DM-24 2.0 release notes 15
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 16
    DM-24 playback or recording when you are leaning over the DM-24 adjusting parameters. Track arming On the MIDI/MC the Mackie HDR-24/96 and MDR-24/ 96 require the MASKED(41h) setting. The DM-24 is now fully popup changes Internal MIDI Time Code generator The DM-24 now has its own generator, which can
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 17
    24 of the main manual for full details. GPI functionality This release of the software added GPI functionality to the DM-24 DM-24, or they can be time events, triggered when the timecode source reaches a preset point. The DM-24 port for any manual events. If available from the manual events. • MUTE
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 18
    Fader Pulses Fader Transitions Fader movement in either direction can also be used to trigger pulse events (as shown in the illustration below): 18 TASCAM DM-24 2.0 release notes Fader movement (pulses) Time events When a port type has been set as a TIME EVENT on the SETUP half of the screen, it
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 19
    messages are sent by each DM-24 control. This screen shows the faders and pan settings: NOTE The following MIDI controllers may not be assigned to DM-24 controls: 0, 6, 32, 38, and 96 through 127. Warning messages are shown if duplicate assignments are attempted. TASCAM DM-24 2.0 release notes 19
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 20
    headed arrow usually used to denote a closed loop device. There is one parameter which may be set here-the MIDI channel (from 1 through 16). 20 TASCAM DM-24 2.0 release notes The setup enables MIDI to be received by the HUI emulation as well as setting the ID of the device. HUI transport emulation
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 21
    four characters of the names on the DM-24 display. Note that this may produce some problems if you are not careful with the names, so you should use the first four characters to identify tracks, for example, BasD and BasG rather than Bass Drum and Bass Guitar. TASCAM DM-24 2.0 release notes 21
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 22
    ) to begin writing or overwriting at the control's current value. While moving the con- Auto or Manual Revert trol, you can release the TOUCH key. Write mode is still enabled for this control. 3 Make as well as its previous "undo all mix moves" function. 22 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 23
    DM-24 the TRIM ALL function (also described in the main manual): 1 Enable TRIM ALL in the AUTO MAIN screen functionality described in the manual (for example, the operation is performed, the DM-24 waits until the timecode stops has been improved. Auto Fade Problems were occasionally reported when an
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 24
    to audio and slate (TO STUDIO AND SLATE) Note that in the 1.60 software release, this mode was not supported. • Talkback to studio only (TO STUDIO) • Talkback to slate only (TO SLATE) • Punch in and punch on the currentlyselected channel (EQ On/Off for Current CH) 24 TASCAM DM-24 2.0 release notes
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 25
    1- 8 DIRECT 9- 16 STEREO L STEREO R BUSS 1 BUSS 2 BUSS 3 BUSS 4 BUSS 5 BUSS 6 BUSS 7 BUSS 8 AUX 1 AUX 2 AUX 3 AUX 4 AUX 5 AUX 6 SOLO SENSE TASCAM DM-24 2.0 release notes 25 TASCAM DM-24 Block Diagram Ver 2.00 INPUT SOURCE OUTPUT SOURCE MIC/LINE 1-16 +48V MIC OL INST -2dBu -56dBu to -2dBu LINE
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 26
    1-4 RTN-B 1-4 RTN-C 1-4 STEREO L STEREO BRUSS 1 BUSS 2 BUSS 3 BUSS 4 BUSS 5 BUSS 6 BUSS 7 BUSS 8 AUX 1 AUX 2 AUX 3 AUX 4 CROOM L CROOM R DIRECT 1- 4 DIRECT 5- 8 TASCAM DM-24 HS Block Diagram Ver 2.00 INPUT SOURCE OUTPUT SOURCE MIC/LINE 1-8 OL +48V INST MIC -2dBu -56dBu to -2dBu LINE -42dBu to
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 27
    2.0-Release notes-Level diagram Level diagram TASCAM DM-24 2.0 release notes 27 +20 (dBV) +10 0 (dBu) +20 LINE +12dBu +10 MIC 0 -2dBu MIC/LINE IN 1-16 (H.ROOM -20 -13.3dBu -30 (dBu) (dBV) +20 +20 +10 +10 0 0 -10dBV -10 -10 STUDIO OUTPUT -20 -20 TASCAM DM-24 Level Diagram Ver 2.00
  • TASCAM IF-FW/DM | Installation and Use v 2.0 Manual Addendum - Page 28
    Acknowledgements HUI™ is a trademark of Mackie Designs Inc. All other brand names are trademarks or registered trademarks of their respective owners. DM-24 TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: (323) 726-0303
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
DM-24
Digital Mixing Console
Version 2.0 — RELEASE NOTES
9101446901