TP-Link T1500G-10PS T1500G-10PSUN V1 Intallation Guide
TP-Link T1500G-10PS Manual
 |
View all TP-Link T1500G-10PS manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1500G-10PS manual content summary:
- TP-Link T1500G-10PS | T1500G-10PSUN V1 Intallation Guide - Page 1
address is 192.168.0.x ("x" is any number from 2 to 254). Subnet Mask is 255.255.255.0. For details, please refer to Appendix B in the User Guide on the resource CD. 2. Enter admin for both the User Name and Password in the lower case letters. Then click the Login button or press - TP-Link T1500G-10PS | T1500G-10PSUN V1 Intallation Guide - Page 2
5 because of the overload. For technical support and other information, please visit http://www.tp-link.com/support FCC STATEMENT This equipment has been tested and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
-
1 -
2
 |
 |
7106506648
REV1.0.0
JetStream 8-Port Gigabit Smart PoE Switch with 2 SFP Slots
T1500G-10PS (TL-SG2210P)
Ethernet Ports (1-8)
1. To access the GUI of the switch, open a browser and type the default
management address http://192.168.0.1 in the address field of the
browser, then press the Enter key.
Note:
To log in to the switch, the IP address
of your PC should be set in the same
subnet as that of the switch. The IP
address is 192.168.0.x (”x” is any
number from 2 to 254). Subnet Mask
is 255.255.255.0. For details, please
refer to Appendix B in the User Guide
on the resource CD.
2. Enter admin for both the User Name
and Password in the lower case
letters. Then click the Login button
or press the Enter key.
3. After a successful login, the main
page will appear as follows, and you
can click the menu on the left side
to configure the corresponding
functions.
Note:
For more details about how to configure the switch, see the User Guide on
the resource CD.
PC
SFP Slots
IP Camera
AP
IP Phone
PoE Devices
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. Maximum PoE power is 15.4W for each PoE port and 53W for all PoE ports.
DC Power Adapter
AC Power Cord
1
2
3
LED Explanation
Installation Guide
Configuration
Connection
On:
Power on
Off:
Power off
Power
Power
SPF1/SFP2
On(Green):
Connected to a 1000Mbps
device
On(Yellow):
Connected to a 100Mbps
device
Flashing:
Transmitting/receiving data
SPF1
SPF2
Flashing:
System running normally
On/Off:
System running abnormally
System
System
On:
46W≤Total power supply<53W
Flashing:
Total power supply keeps≥
46W more than 2 minutes
Off:
Total power supply<46W
PoE MAX
PoE MAX
PoE Status (port 1-8)
On:
Providing PoE power
Flashing:
Current-overload/Short-circuit/
Connected to a Non-standard PD/Power
exceeded the user-defined value
Off:
Not providing PoE Power
PoE Status
Link/Act (port 1-8)
On(Green):
Connected to a 1000Mbps device
On(Yellow):
Connected to a 10/100Mbps
device
Flashing:
Transmitting/receiving data
Link/Act
Internet