TP-Link T1600G-18TSTL-SG2216 T1600G-18TSUN V1 Installation Guide
TP-Link T1600G-18TSTL-SG2216 Manual
 |
View all TP-Link T1600G-18TSTL-SG2216 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1600G-18TSTL-SG2216 manual content summary:
- TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 1
Business Networking Solution Installation Guide JetStream Gigabit Smart Switch T1600G-18TS (TL-SG2216) T1600G-28TS (TL-SG2424) / T1600G-52TS (TL-SG2452) T1600G-28PS (TL-SG2424P) / T1600G-52PS (TL-SG2452P) - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 2
- TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 3
connection of the switch. Chapter 5 Configuration. This chapter instructs you to configure the switch via Web Interface and CLI commands. Appendix A Troubleshooting. Appendix B Specifications. Audience This Installation Guide is for: Network Engineer Network Administrator Conventions • Some - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 4
20 4.3 Verify Installation 20 4.4 Power On 21 4.5 Initialization 21 Chapter 5 Configuration 22 5.1 Configure the Switch via GUI 22 5.2 Configure the Switch Using CLI 23 Appendix A Troubleshooting--------- 24 Appendix B Hardware Specifications----- 25 II Contents - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 5
and L2+ management features. It provides a variety of service features and multiple powerful functions with high security. The EIA Power Sourcing Equipment (PSE*). All the Ethernet RJ45 ports on the switch support Power over Ethernet (PoE*) function, which can automatically detect and supply power - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 6
has a corresponding Link/Act LED and a 1000Mbps LED. SFP Port Designed to install the SFP module. T1600G-18TS features 2 individual SFP ports and supports 1000M SFP module connection only. The front panel of T1600G-28TS is shown as the following figure. Figure 1-2 Front Panel of T1600G-28TS LEDs - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 7
has a corresponding Link/Act LED and a 1000Mbps LED. SFP Port Designed to install the SFP module. T1600G-28TS features 4 individual SFP ports and supports 1000M SFP module connection only. The front panel of T1600G-52TS is shown as the following figure. Figure 1-3 Front Panel of T1600G-52TS Reset - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 8
or 1000Mbps. Each has a corresponding 10/100/1000Mbps LED. SFP Port Designed to install the SFP module. T1600G-52TS features 4 individual SFP ports and supports 1000M SFP module connection only. The front panel of T1600G-28PS is shown as the following figure. Figure 1-4 Front Panel of T1600G-28PS - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 9
JetStream Gigabit Smart Switch LEDs T1600G-28PS has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission status. When the PoE LED is on, the port LED is indicating the power supply status. By default, - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 10
has a corresponding Speed or PoE LED. SFP Port Designed to install the SFP module. T1600G-28PS switch features 4 features 4 individual SFP ports and supports 1000M SFP module connection only. The front panel of T1600G-52PS is shown as the following figure. Figure 1-5 Front Panel of T1600G-52PS - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 11
JetStream Gigabit Smart Switch When the Speed LED is on, the port LED is indicating the data transmission status. LED Status Indication On The switch is powered on PWR Off The switch is powered off or power supply is abnormal Flashing Power supply is abnormal Flashing SYS On/Off The - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 12
or 1000Mbps. Each has a corresponding Speed or PoE LED. SFP Port Designed to install the SFP module. T1600G-52PS switch features 4 individual SFP ports and supports 1000M SFP module connection only. ■■ Rear Panel The rear panel of T160 0G -18TS/ T160 0G -28TS/ T160 0G -52TS/ T160 0G -28PS/ T1600G - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 13
any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Business Networking Solution Installation Guide Two mounting brackets, eight One Resource CD screws and four rubber feet 2.2 Safety Precautions To avoid any device - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 14
, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table. Environment Operating Storage - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 15
the device on a rack or a flat workbench, please note the following items: ■■ The rack or workbench is flat and stable, and sturdy enough to support the weight of 5.5kg at least. ■■ The rack or workbench has a good ventilation system. The equipment room is well ventilated. ■■ The rack is well - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 16
the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the grounding and stability of the rack. 2. - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 17
Figure 2-9 Rack Installation JetStream Gigabit Smart Switch Rack Caution: ■■ Please set 5~10cm gaps around the device for air circulation. ■■ Please avoid any heavy thing placed on the device. ■■ Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 18
JetStream Gigabit Smart Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 19
small as possible. ■■ Requirements for the distance between Ethernet cable and other pipelines are shown in the table. Other Pipelines Down-conductor PE Service pipe Compressed air pipe Thermal pipe (not wrapped) Thermal pipe (wrapped) Gas pipe Ethernet Cable Min Parallel Net Length L (mm) 1000 50 - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 20
which is also a necessary measure to protect the body from electric shock. In different environments, the device may be grounded differently. The following will instruct you to connect the device to the ground in two ways, connecting to the ground via the power supply or connecting to the ground via - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 21
Figure 3-1 Connecting to the Ground via Power Supply JetStream Gigabit Smart Switch Switch (Rear Panel) AC Power Cord (with PE cable) Note: ■■ The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 22
JetStream Gigabit Smart Switch Equipotential Bonding Equipotential Bonding is the practice of intentionally electrically connecting all earthed systems to the same grounding grid or connecting the grounding grids of all the earthed systems together through the ground or overground metal so as to - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 23
JetStream Gigabit Smart Switch Signal lightning arrester is used to protect RJ45 ports of the device from lightning. When cabling outdoors, please install a signal lightning arrester before connecting the cable to the device. When purchasing or using a signal lightning arrester, please observe the - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 24
JetStream Gigabit Smart Switch Chapter 4 Connection 4.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown. Figure 4-1 Connecting the RJ45 Port RJ45 Port RJ45 Cable 4.2 SFP Port Connect the SFP port to a SFP module as shown below. - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 25
4.4 Power On JetStream Gigabit Smart Switch Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector into a power outlet as the following figure shown. Figure 4-3 Connecting to Power Supply 2 1 Note: The figure is to illustrate the - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 26
is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B in the User Guide on the Resource CD. 2. Enter admin for the default User Name and Password, both in lower case letters. Then - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 27
Figure 5-3 Main Page of the Switch JetStream Gigabit Smart Switch 5.2 Configure the Switch Using CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 28
JetStream Gigabit Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? Press the Reset button for at least 5 seconds be set as 192.168.0.x ("x" is any number from 2 to 254) and Subnet Mask as 255.255.255.0. 24 Appendix A Troubleshooting - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 29
Appendix B Specifications JetStream Gigabit Smart Switch Item Content Standards IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3z, IEEE 802.3x, IEEE 802.1p, IEEE 802.1q, IEEE 802.1x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w IEEE 802.3af/at (T1600G-28PS/T1600G-52PS) - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 30
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in electric shock and voiding the limited warranty. If you need service, please contact us. • Avoid water and wet locations. - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 31
BSMI Notice 1 2 3 4 5 6 7 Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) Explanation of the symbols on the product label Symbol Explanation AC voltage Indoor use only RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). - TP-Link T1600G-18TSTL-SG2216 | T1600G-18TSUN V1 Installation Guide - Page 32
other information, please visit http://www.tp-link.com/support, or simply scan the QR code. The products products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
T1600G-18TS (TL-SG2216)
T1600G-28TS (TL-SG2424)
/
T1600G-52TS (TL-SG2452)
T1600G-28PS (TL-SG2424P)
/
T1600G-52PS (TL-SG2452P)
Business Networking Solution
Installation Guide
JetStream Gigabit Smart Switch